Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Belkin F5U501
Summary of Contents for Belkin F5U501
- Page 1 Belkin Components ® FirePath ™ IEEE 1394 Instruction Manual F5U501 P73289...
-
Page 2: Introduction And System Requirements
™ IEEE 1394 card. Now, you can add three 400Mbps FireWire ® ports to your Windows ® 98 system, and enjoy the blazing speed and Plug-and-Play ease of next-generation FireWire ® devices. System Requirements: • 486 processor or faster •... -
Page 3: Installation
2. Open up the case of your computer. Refer to your computer user manual for details on how to do this. Be sure to touch any bare metal portion of your computer case to discharge yourself of any static electricity, which can damage your computer, or the FireWire ®... - Page 4 (continued) 3. Locate the PCI slots on your computer’s main circuit board. The PCI slots are white in color, and are made of hard plastic. Locate a free PCI slot. Any slot will do. Remove the metal plate that covers the rear slot corresponding to the PCI slot you had selected.
- Page 5 4. Remove the FireWire ® card from its protective static bag. Handle it by the metal bracket only, and do not touch the gold edge connectors. Insert the card into the PCI slot, carefully aligning the rear bracket to the computer case.
- Page 6 Installation (continued) 5. Fasten the card securely using the screw that was used to hold the rear bracket. 6. Re-attach the case of your computer.
- Page 7 As Windows ® boots up, it will recognize the new FireWire ® card in your system. Click on “Next”. 8. In the next dialog as shown below, select "Display a list of …" then click on “Next”.
- Page 8 “Next”. NOTE: If Texas Instruments is not one of the choices, click on “Show all hardware”. On the screen that appears, under manufactures, select Texas Instruments then under models, select Texas Instruments OHCI Compliant IEEE 1394 Host Controller.
- Page 9 CD-ROM drive of your computer if necessary. Click “Next” to proceed: 11. When Windows is done copying and installing the proper ® driver files, it will show you the final dialog below. Click on “Finish” to end.
- Page 10 Installation (continued) That’s it! You’re all done. Now you can enjoy all the benefits of super fast 400Mbps FireWire devices on your computer. If you have a DV Digital camcorder, you can install the Belkin DVcam Driver and the MGI Video Wave III SE. The Belkin DVcam software will allow the 1394 FirePath card to capture amazing video and sound using the MGI video-editing program.
- Page 11 MGI Video Wave III SE requires 800X600 or higher video resolution and 16-bit color depth or higher. 5. To install MGI Video Wave III click on “START” then “RUN”. Enter "D:\Autorun.exe" in the blank where "D:" is the drive letter of your CD-ROM drive as shown above, and click OK.
- Page 12 10. After Launching Video Wave, click on the capture icon (see diagram below). Capture Icon 11. On the next screen that appears, click on the "Settings" button located on at the bottom right hand corner (refer to diagram below). Settings button...
- Page 13 13. Once you are back on the "Capture Screen"(Video Wave Main screen), click the "Video+Audio" button to begin capturing. 14. If you are in VideoWave and want to turn off the camcorder, you will need to exit VideoWave and then turn off the camcorder.
-
Page 14: Fcc Statement
Belkin Components warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. - Page 15 Fax: +44 (0) 1604678330 Belkin Components B.V. Diamantlaan 8 • 2132 WV Hoofddorp • The Netherlands Tel: +31 (0) 235698765 Fax: +31 (0) 235612694 © 2000 Belkin Components. All rights reserved. All trade names are registered trademarks of respective manufacturers listed.