Safety Precautions; Installation Site; Precautions For Safe Use; Precautions For Correct Use - Omron V680 Product Manual

Safety Precautions

Do not use this product as a detection device to protect
people.
Note: This catalog is intended only to help select the appropriate
product. Be sure to read the User's Manual for usage
precautions prior to using the product.

Precautions for Safe Use

To ensure safety, be sure to follow the following precautions:
1. Do not operate this product in any flammable, explosive, or corro-
sive gas environment.
2. Do not disassemble, repair, or remodel this product.
3. Tighten the base lock screws and terminal block screws com-
pletely.
4. Be sure to use wiring crimp terminals of the specified size.
5. If any cable has a locking mechanism, be sure to check that it has
been locked before using it.
6. The DC power supply must be within the specified rating (24 VDC
+10%/ − 15%).
7. Do not reverse the power supply connection.
8. Do not insert water, wire, etc., into any of the gaps in the case.
Doing so may cause fire or electric shock.
9. Turn OFF the Controller or ID Sensor Unit power before attaching
or removing the Read/Write Antenna.
10.In the event that the product exhibits any abnormal condition,
immediately stop using the system, turn OFF the power, and con-
tact your OMRON sales representative.
11.Dispose of this product as industrial waste.
12.Be sure to follow any other warnings, cautions, and notices given
in this document.

Precautions for Correct Use

Please observe the following precautions to prevent failure to
operate, malfunctions, or undesirable effects on product
performance.

Installation Site

Install the product at a location where:
• It is not exposed to corrosive gases, dust, metal chips, or salt.
• The ambient operating temperature is within the range stipulated in
the specifications.
• There are no sudden variations in temperature (no condensation).
• The ambient operating humidity is within the range stipulated in the
specifications.
• No vibration or shock exceeding the values stipulated in the
specifications is transmitted directly to the body of the product.
• It is not subject to splashing water, oil, or chemical substances.
Installation
• The product uses the 13.56-MHz frequency band to communicate
with ID Tags. Some devices, such as some motors, inverters, and
switching power supplies, generate electromagnetic waves (i.e.,
noise) that can affect communications with ID Tags. If any of these
devices are nearby, communications with ID Tags may be affected
or ID Tags may be destroyed. If the product is to be used near such
devices, check the effects on communications before using the
product.
• To minimize the general influence of noise, observe the following
precautions:
1. Ground any metallic material located around this device to
100 Ω or less.
2. Keep the product away from high voltage and heavy current.
WARNING
• Do not use products that are not waterproof in misty environments.
• Do not subject the products to chemicals that adversely affect
product materials.
• When installing the product, tighten screws to the following torque:
Controller:
ID Sensor Unit:
V680-HS51 Read/Write Antenna: 6 N·m
V680-HS52 Read/Write Antenna: 40 N·m
V680-HS63 Read/Write Antenna: 1.2 N·m
V680-HS65 Read/Write Antenna: 1.2 N·m
• When Read/Write Antennas are mounted side-by-side, mutual
interference may reduce the transmission performance. Refer to
the RFID System Amplifier and Antennas/ID Tags User's Manual to
mount them in a way that will prevent mutual interference.
Storage
Store the product at a location where:
• It is not exposed to corrosive gases, dust, metal chips, or salt.
• The ambient storage temperature is within the range stipulated in
the specifications.
• There are no sudden variations in temperature (no condensation).
• The ambient storage humidity is within the range stipulated in the
specifications.
• No vibration or shock exceeding the values stipulated in the
specifications is transmitted directly to the body of the product.
• It is not subject to splashing water, oil, or chemical substances.
Cleaning
Do not use thinner, benzene, acetone, or kerosene for cleaning.
Using these substances may dissolve the resin material and the
case.
V680 Series
1.2 N·m max.
0.4 N·m
35
RFID System