Rating And Performance - Omron F3SP-U3P-TGR Datasheet

Rating and Performance

Sensors
E3FS-10B4 series
Sensing method
Controller
Supply voltage
Effective aperture angle (EAA)
Current consumption
Sensing distance
Standard sensing object
Response time
Control output
Test input (Emitter)
Power supply reset time
Ambient light intensity
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Malfunction
Vibration resistance
Operating limit
Malfunction
Shock resistance
Operating limit
Degree of protection
Light source
Operation indicators
Protection
Weight (in packaging)
Applicable standard
Accessories
Parallel Operating Range
600
Emitter
Y
400
X
Receiver
200
0
−200
−400
−600
0 2 4 6 8
E3FS
Through-beam
F3SP-U3P-TGR, F3SP-U5P-TGR
24 VDC ± 10% (ripple p-p 10% max.)
±5° (at 3 m)
Emitter:50 mA max.
Receiver:25 mA max.
10 m
Opaque object: 11 mm min. in diameter
2.0 ms (E3FS only) Response time of controller = Response time of the system
PNP transistor output, load current: 100 mA max., residual voltage: 2 V max. (Except for volta-
ge drop due to cable extension)
21.5 to 24 VDC: Emitter OFF (source current: 3 mA max.)
Open or 0 to 2.5 V: Emitter ON (leakage current: 0.1 mA max.)
100 ms
Incandescent lamp: 3.000 lx max. (light intensity on the receiver surface)
Sunlight: 10,000 lx max. (light intensity on the receiver surface)
Operating: -10 to 55°C, storage: -30 to 70°C (with no icing or condensation)
Operating: 35% to 85%, storage: 35% to 95% (with no icing or condensation)
20 MΩ min. (at 500 VDC)
1,000 VAC 50/60 Hz 1 min
10 to 55 Hz, double amplitude: 1.5 mm, 2 h each in the X, Y, and Z directions
10 to 55 Hz, double amplitude: 0.7 mm, 50 min each in the X, Y, and Z directions
500 m/s² (approx. 50 G), 3 times each in the X, Y, and Z directions
100 m/s² (approx. 10 G), 1,000 times in the X, Y, and Z directions
IP67 (IEC standard)
Infrared LED
Emitter: Emitting (orange)
Receiver: Output ON (green), Output OFF (red)
Output short-circuit protection, reverse polarity protection
E3FS-10B4 2M (ABS resin case): approx. 150 g for 1 set (weight without cable: approx. 55 g)
E3FS-10B4-M1-M (metal case): approx. 125 g for 1 set
IEC61496-1, EN61496-1 Type 2 ESPE (Electro-Sensitive Protective Equipment)
IEC61496-2, prEN61496-2 Type 2 AOPD (Active Opto-electronic Protective Devices)
Emitter, Receiver, four nuts for mounting, and an instruction manual
Mutual interference Range
800
Y
600
X
Receiver
400
200
0
−200
−400
−600
−800
10 12 0 2
Distance X (m)
Emitter
4 6 8 10 12
Distance X (m)
Excess Gain Ratio
10
9
8
7
6
5
4
3
2
1
0
0 5 10 15 20 25 30
Distance (m)
G-65