Contents Introduction Introduction The following items are included in the carton: Declaration of conformity • Product complete with grille Symbols used in this guide • Grille fixing screws (9) Important safety and installation instructions 3/4 • Wireless wall controller Application Note: This heater must be used with the Product Information HHPS01 wireless controller (supplied) It will not...
Symbols This manual contains information and prescriptions marked by the following symbols: Ignoring these safety High temperature Ignoring these safety provisions marked by surface. provisions marked by the symbol “caution: Take utmost care the symbol “caution: electricity” may to prevent people hazard”...
Important safety and installation instructions Prior to installation, read these installation and operating instructions. The installation and operation should also be in accordance with national regulations and accepted codes of good practice. 6. Electrical connection IMPORTANT: Connection to the power supply must be effected by means of a fixed power cable which is fitted with a plug-type connection or a two pole isolating switch with a minimum contact opening of 3 mm.
Product performance Installation Preparation Power a) Ensure the mounting surface is capable of Supply Cable supporting this heater appliance and that the area can provide the installation clearances shown in diagram 1. Suspension chains 508 490 or threaded rods Choice of mounting positions b) If installing this heater appliance into a false PROG MODE...
Page 6
This heater appliance may 6. Replace the fascia and ensure it is secured with all the original screws. be mounted in the following methods Unit Operation To mount the heater appliance direct to Please note: This heater will NOT function without the ceiling the wall mounted wireless controller (supplied) .
HHPS01 Wireless Controller – Quick Set Up 1. Ensure the heater is installed and connected to the mains power supply. DO NOT TURN THE MAINS POWER ON AT THE WALL UNTIL ASKED IN THE INSTRUCTIONS BELOW. Note: Failure to switch on the power and initiate pairing within 20 seconds will result in the heater 2.
Page 8
5. To set the required thermostat temperature press the TEMP button to bring up the adjustment icon on the screen. Use the + and – buttons to select the required temperature. The radiator symbol will appear when heating is demanded. 6.
Electrical Connection 6. With the electrical connections made ensure that the mains cable does not obstruct any Heat Emitter moving parts of the fan Connect the mains electrical supply cable (3 core, stranded 2.5mm²) via a switched fused isolator, fused at 20A to the heating appliance. Do not energise the supply until the panels described have been returned and secured.
Fault finding In the event of any difficulty, please contact us on +44 (0) 1245 324560. Fault Checking/Solution Check the power supply is switched ON Check fuse in fused spur Check the fan is switched on Fan does not run/no heat output Check the battery in the controller and replace if necessary Check the wireless controller thermostat is calling for heat Check the wireless controller is paired to the heater...
Important safety and installation instructions Please read this user manual before operating this appliance. The operation should also be in accordance with national regulations and accepted codes of good practice. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
How it works How to operate Cooler air is drawn in by the fan and heated as it 1. Before switching the heater on, please ensure passes through the heating element before being the fascia grille is free from obstruction. discharged gently back into the room.
Fault finding This product is covered by a free 5-year parts and labour guarantee. Please refer to the Fault finding table below for advice. In the event of difficulty, please contact us on +44 (0) 1245 324560. Fault Checking/Solution Check the power supply is switched ON Check fuse in fused spur Check the fan is switched on Fan does not run/no heat output...
HHPS01 Controller Installation and control user manual PROG MODE TIME TEMP HHPS01 WIRELESS CONTROLLER Issue 007 | April 2024 ENGLISH | UK | IRL | SmithsEP.co.uk Issue 007 - April 2024 | SmithsEP.co.uk | 17...
Contents Introduction Introduction In the event of items missing or visible damage please contact us on 01245 324560. Declaration of conformity Product dimensions Keep the batteries out of reach of children • Do NOT use if the battery compartment is Pairing the heater to the HHPS01 not secure Basic Operation...
Declaration of conformity Product dimensions In accordance with UK Government Guidance. THE APPLIANCES DETAILED HEREON HAVE BEEN INSPECTED AND TESTED, AND CONFORM TO THE REQUIREMENTS OF THE FOLLOWING UK STATUTORY INSTRUMENTS WHERE APPLICABLE: Electrical Equipment (Safety) Regulations 2016 SI. 2016 1101 Electromagnetic Compatibility Regulations 2016 PROG MODE...
Overview The HHPS01 wireless controller can control an unlimited number products provided they are within range. To do this, the controller must be paired with each heater. The heater will not operate until it has been paired to the controller. Pairing the heater to the HHPS01 In order to pair your appliance with the controller you must:...
Boost mode The boost feature increases the room temperature for 15 minutes. To amend the set temperature when in BOOST mode, activate the display and then press TEMP. Next, use the + and - buttons to change the temperature. Once the temperature is set, you Auto mode can leave the display to return to the main screen and the settings will be saved.
Displaying the time/temperature Keys locking The HHPS01 can display either the time & day Press and hold TIME and TEMP together for 5 or the room temperature when in one of the 4 seconds. The display will show the symbol. standard operating modes.
Setting the automatic program schedule An example of one day program on HHPS01 PROGRAM 1 PROGRAM 2 PROGRAM 3 PROGRAM 4 PROGRAM 5 PROGRAM 6 °C 19°C 22°C 22°C 16°C 10°C 4°C 06.00 08.00 12.00 14.00 16.00 22.00 Logic diagram for setting program on HHPS01 Step 3: Press the PROG button.
Set program inactive Step 8: Press the PROG button. The temperature If you do not require the use of all 6 programs should flash. Use the they can be deactivated. When in programming + and - buttons to mode select the program you want to make select a frost protection inactive and press the TIME button.
Step 4: Use the + and - 5 - Set maximum buttons to select the day temperature to copy the programs to. Step 5: Press the TIME 6 - Enable/disable open window button to copy the detection programs. The ‘TO’ will flash to confirm the programs have been copied.
B - Program mode select. Choose between a 7-day, 5-day 2-day or a 24 hour timer. C - Select operating mode: 1 = temperature control 2 = manual control The bracket acts as a holder for the controller. The controller can be removed from the D - Enable/disable SL bracket easily to...
Registering your product Disposal As part of the policy of continuous product Thank you for purchasing a Smith’s product. It has improvement, Smith’s Environmental Products LTD been designed and manufactured to the highest reserves the right to alter specification without quality standards to ensure it gives you efficient prior notice.
Page 28
Happy to help To view the full product information download the datasheet at: Smith’s Environmental Products Ltd is one of the leading manufacturers of heating and cooling www.SmithsEP.co.uk products in the UK. We are committed to achieving the highest standards and our faith is For product information, customer services or supported by a free parts and labour guarantee sales support call us on +44 (0) 1245 324900...