Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Swann Smith's Caspian EC Series
Summary of Contents for Swann Smith's Caspian EC Series
- Page 1 Caspian - EC variants ® with Smart Controls Installation, commissioning and user manual 60 | 90 | 120 | 150 | 180 EC Series Fan Convectors Issue 003 | August 2020 ENGLISH | UK | IRL | SmithsEP.co.uk Issue 003 - August 2020 | SmithsEP.co.uk | 1...
-
Page 2: Table Of Contents
Contents Introduction Introduction These heaters must not be installed in wet rooms or other high humidity areas. Declaration of conformity Symbols used in this guide These heaters are designed for use on standard two-pipe pumped central heating systems with Important safety and installation instructions a maximum water temperature of 86°C and a maximum pressure of 6 bar (88lbs/in.). -
Page 3: Declaration Of Conformity
Declaration of conformity Symbols EC Declaration of conformity This manual contains information and prescriptions marked by the following symbols. We, Smith’s Environmental Products Limited 1-2 Blackall Industrial Estate South Woodham Ferrers Ignoring these safety provisions Chelmsford marked by the symbol “caution: Essex CM3 5UW hazard”... -
Page 4: Important Safety And Installation Instructions
Important safety and installation instructions Prior to installation, read these installation and operating instructions. The installation and operation should also be in accordance with national regulations and accepted codes of good practice. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. - Page 5 8. Electrical connection Important: Connection to the power supply must be effected by means of a fixed power cable via a two pole isolating switch (fused spur) with a minimum contact opening of 3mm. The fused spur must not be directly below the heater but should be accessible after completion of the installation.
-
Page 6: Product Dimensions
Product dimensions Caspian UV Caspian SL Electrical supply in this side Electrical supply in this side Pipe centres Pipe centres Model Model 1195 1195 1495 1495 1795 1795 Caspian FF Caspian TT Electrical supply in this side Electrical supply in this side Pipe centres Pipe centres Model... - Page 7 Caspian EXT 1800 Model 1195 1495 1795 Electrical supply Pipe centres in this side Issue 003 - August 2020 | SmithsEP.co.uk | 7...
-
Page 8: Control Mounting
Control mounting options/configurations Predetermined at time of order Flush mounted Internally mounted (tamper proof) Wall mounted (remote) 8 | SmithsEP.co.uk | Issue 003 - August 2020... -
Page 9: Wiring Diagrams
Wiring diagram RELAY HF105F-4 NO NC WHITE WHITE BROWN BLACK BLACK BLACK GREY GREY GREY BLUE BLACK BLACK PSU(230VAC/24VDC) DRIVER BROWN BROWN WHITE BLUE BLUE BLUE WAGO Series Connection 862 Block BROWN GREEN BLUE BROWN BROWN BLACK GREEN BLUE GREEN GREEN BROWN BROWN... -
Page 10: Product Performance
Product performance Heat output - EC Model Control 40°C 45°C 50°C 55°C 60°C 65°C 70°C 75°C 80°C Reference Speed Voltage VDC 0.85 1.20 1.45 1.80 2.16 2.35 2.73 3.08 3.40 1.02 1.53 1.92 2.37 2.76 3.18 3.58 4.05 4.38 EC 60 High 1.18 1.85... - Page 11 Model Hydraulic Water Nominal Weight (KG) Reference Speed Resistance (KPA) Capacity (L) 1.38 1.69 EC 60 23.00 0.92 High 2.00 4.70 5.85 EC 90 36.00 1.50 High 7.00 17.78 20.59 EC 120 45.00 2.08 High 23.40 22.23 29.46 EC 150 60.00 2.58 High...
-
Page 12: Mounting Options
Mounting options ➠ ➠ Ceiling (edge) Ceiling (centre) Wall Wall ➠ ➠ Floor Floor Caspian SL Caspian UV ➠ ➠ Ceiling (centre) ➠ Ceiling (edge) ➠ ➠ Wall Wall ➠ ➠ CEILLING Floor Floor CASPIAN EXT Caspian FF Caspian TT Control options depend upon the product location. - Page 13 Notes Issue 003 - August 2020 | SmithsEP.co.uk | 13...
-
Page 14: Installation
Installation 1. Unlock the front access panel Unlock and lower the front access panel using the keys supplied. The keys come cable tied to the back of the heater. Note: The system must be flushed prior to fitting this heater. Failure to comply with this may effect the warranty. -
Page 15: Installation - Remote Smart Controller
5. Electrical supply and electrical 5. Fasten body of thermostat and the mounting plate. See Fig 5. connection 6. When using external pattress box assemble as shown. See Fig 6. Electrical supply to the unit must be nominal 230VAC 50~Hz. Electrical connection to the product is via a 3 way terminal block inside the product (L, N, E), on electrical panel. -
Page 16: Commissioning
Commissioning Connecting remote smart controller to the heater 1. Turn on the electrical supply at the fused spur. 1. Feed the connector end of the wire harness 2. Set the thermostat to maximum using the increase button on the controller. through the cut outs in the back or underside of the unit. -
Page 17: User Guide For Wi-Fi Thermostat
Quick user guide for Wi-Fi Button functions Thermostat Function Increase Button Decrease Button Fan Speed Low, Medium, High, Auto, Off Long press Short press (2sec) Heat/Cool/Eco Digital Offset, Time Mode selection Button Permanent override Programmable Program- AUTO scedule mable Heat/Cool/Eco Offset selection Time&Date... -
Page 18: Getting Started - Programming
LCD Icon descriptions Getting started All units are factory configured in off-line stand alone mode and tested for function when built. Should your unit require setup from storage or reconfiguration to “Smart Home” App control follow the steps below to ensure successful setup and operation. - Page 19 1. When powered for the first time the control 5. Select the thermostat mode, although this unit is heating only by setting heating and cooling will boot (Software version will appear) after a allows the use of fan only/ventilation sort time the display will change to show if required.
- Page 20 Changing from offline Scan for equipment Press from the App and mode to online mode follow the on screen instructions. If you want to use the internet App and the Universal Gateway Hub UG600 (available as an accessory product code: HACA33130), you need to change your thermostat settings from offline mode to online mode.
- Page 21 Factory reset User Guide If you have made an error or need to change For further information and to view detail of set your system parameters, or want to return to up, operation and parameters, please consult the the factory settings, please follow steps below. full manual at: By performing this action you will lose all your https://salus-controls.com/uk/product/fc600/#downloads...
-
Page 22: Maintenance
Maintenance Warning! Isolate from the electrical supply The fan(s) and motors should not require servicing. before performing any work on the unit. Please contact your supplier if damaged. The internal air filter is removable for servicing. To replace filter use reverse the removal To gain access to the filter unlock and lower the instructions and ensure the lower front access front access panel, remove the 2 screws from the... -
Page 23: Accessories
Accessories Disposal As part of the policy of continuous product Air inlet filters for all models improvement, Smith’s Environmental Products LTD Universal Gateway Hub UG600 for use with reserves the right to alter specification without internet App control prior notice. For accessories or spares please refer to our price Products with this symbol (crossed out wheelie list, contact your supplier or Smith’s Environmental... - Page 24 Happy to help To view the full product information download the datasheet at: Smith’s Environmental Products Ltd is one of the leading manufacturers of heating and cooling www.SmithsEP.co.uk products in the UK. We are committed to achieving the highest standards and our faith is For product information, customer services or supported by a free parts and labour guarantee sales support call us on +44 (0) 1245 324900...