Technical Data; Drill Safety Warnings - Milwaukee M18BLPDRC-502C Original Instructions Manual

TECHNICAL DATA

Type
Production code
Voltage battery pack
No-load speed, 1st gear
No-load speed, 2nd gear
Impact range, 1st gear
Impact range, 2nd gear
Torque
Drilling capacity in wood
with fl at bit
with auger bit
with hole saw
with selfeed bit
Drilling capacity in brick and tile
Wood screws (without pre-drilling)
Drill chuck range
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12.0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise information: Measured values determined according to
EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Always wear ear protectors!
Vibration information: Total vibration values (vector sum in the
three axes) determined according to EN 62841.
Vibration emission value a / Uncertainty K
h
Impact drilling into concrete
Drilling into metal
Screwing
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN
62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING
Read all safety warnings, instructions,
illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
Wear ear protectors when impact drilling. Exposure to noise can
cause hearing loss.
Brace the tool properly before use. This tool produces a high
output torque and without properly bracing the tool during operation,
loss of control may occur resulting in personal injury.
20
470 868 - M18BLDDRC, M18BLPDRC.indd 20 470 868 - M18BLDDRC, M18BLPDRC.indd 20
M18 BLDDRC
Cordless Drill Driver
4817 09 01 XXXXXX MJJJJ 4817 46 01 XXXXXX MJJJJ
18 V
0-550 min
0-1700 min
–
–
60,5 Nm
32 mm
25,4 mm
51 mm
1-3/8" (35 mm)
–
13 mm
1,6 – 13 mm
1,5 kg...2,8 kg
79,32 dB(A) / 3 dB(A)
87,32 dB(A) / 3 dB(A)
–
1,64 m/s / 1,5 m/s
2
1,44 m/s / 1,5m/s
2
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed rated
of the drill bit. At higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece, resulting the personal
injury.
Always start drilling at low speed and with the bit tip in contact
with the workpiece. At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting the workpiece, resulting
the personal injury.
Apply pressure only in direct line with the bit and do not apply
excessive pressure. Bits can bend causing breakage or loss of
control, resulting in personal injury.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
WARNING To reduce the risk of injury in applications that produce
a considerable amount of dust, use a Milwaukee dust extraction
solution in accordance with the solution's operating instructions.
ENGLISH
M18 BLPDRC
Cordless percussion drill/driver
18 V
0-550 min
-1 -1
-1 0-1700 min -1
: 0-8250 min
0-25000 min
60,5 Nm
32 mm
25,4 mm
51 mm
1-3/8" (35 mm)
10 mm
13 mm
1,6 – 13 mm
1,5...2,8 kg
-18...+50 °C
M18B...; M18HB...
M12-18...; M1418C6
90,66 dB(A) / 3 dB(A)
98,66 dB(A) / 3 dB(A)
8,31 m/s / 1,5m/s
2
1,64 m/s / 1,5m/s
2 2
1,44 m/s / 1,5 m/s
2 2
05.06.2023 09:24:34 05.06.2023 09:24:34
-1
-1
2
2
2