Table of Contents
Advertisement
KingKORG NEO Parameter Guide
Example: Ribbon controller
MIDI Controller
MIDI Value
0
KingKORG NEO
Virtual Patch Modulation
"CC#16"
0
"CC#16±"
–63
If you assign "CC#16±," "CC#17±," "CC#19±," "CC#20±," or "CC#21±" for
MIDI1–3, the value received via CC#16, 17, 19, 20, or 21 will automatically be
converted before being used for modulation.
g22~26: MIDI Filter
Here is where you can adjust MIDI filter settings. For each type of MIDI
message you can enable or disable reception on the KingKORG NEO.
ProgChg (Program Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Disable, Enable]
This selects whether program changes will be transmitted and received.
Disable:
Program changes will not be transmitted or received.
Enable:
Program changes will be transmitted and received.
BankChg (Bank Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Disable, Enable]
This selects whether bank select messages will be transmitted and received.
Disable:
Program changes will not be transmitted or received.
Enable:
Program changes will be transmitted and received.
CtrlChg (Control Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Disable, Enable]
This selects whether control change messages will be transmitted and
received.
Disable:
Program changes will not be transmitted or received.
Enable:
Program changes will be transmitted and received.
P .Bend (Pitch Bend) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Disable, Enable]
This selects whether pitch bend messages will be transmitted and received.
Disable:
Program changes will not be transmitted or received.
Enable:
Program changes will be transmitted and received.
SysEx (System Exclusive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Disable, Enable]
This selects whether MIDI system exclusive messages will be transmitted and
received.
Disable:
Program changes will not be transmitted or received.
Enable:
Program changes will be transmitted and received.
127
64
127
0
63
g27: MIDI CC#Map (MIDI Control Change Map)
Here is where you can assign control change messages to the principal
parameters.
Parameters that are assigned to an incoming control change will change
together. When you use a knob or button that corresponds to a parameter, the
control change that's assigned here will be transmitted. For some parameters
that have no corresponding knob or button, only reception is supported
(→ p.31 "MIDI messages"
* Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [Porta .Time...VcE .F .Sens]
This selects the parameter that will be assigned
* Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[Off...#119]
This specifies the MIDI control change number (CC#) for the parameter
selected in Parameter.
Editing the CC#Map
1.
Hold down the SHIFT/EXIT button and press the PROGRAM
(GLOBAL) button to switch to Global mode.
2.
Use the PAGE+/– buttons to access the "g27:MIDI CC#Map" page.
TIP:
At this time you can turn the VALUE dial to step through the parameters and view
their status.
3.
Press the VALUE dial.
4.
Use the PAGE+/– buttons to select a parameter, and turn the
VALUE dial to specify the value .
TIP:
If the specified value is also used by another parameter, an asterisk "*" is shown
at the right of the value (Value).
5.
Press the VALUE dial to return to the previous page.
TIP:
The MIDI channel for vocoder parameters will be the same MIDI channel as for timbre A.
8 .
Foot parameters
Here is where you can adjust settings for a foot pedal and foot switch that's
connected to the rear panel. When connecting a foot pedal for the first time,
use the GLOBAL "g34: Foot Pedal" page to perform the calibration
"Calibration"
).
g28: Foot Damper
Polarity (Damper Polarity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [+, –/KORG]
This specifies the polarity of a damper pedal that's connected to the DAMPER
jack.
With the factory settings, this is set to "–/KORG". Use this setting if you're
connecting a damper pedal or pedal switch made by Korg.
TIP:
Use the "–/KORG" setting if a damper pedal switch is not connected.
g29: Foot Assign
Type (Assignable Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[Pedal, Switch]
This specifies the option that's connected to the ASSIGNABLE SW jack.
Pedal:
Choose this setting if a volume pedal or foot controller is connected.
Switch:
Choose this setting if a pedal switch is connected.
- 20 -
).
(→
p.34).
Parameters
(→ p.21
Advertisement
Table of Contents
