Xerox Corporation may void the authority granted by the FCC to operate this equipment. This Class B Digital apparatus meets all the requirements of the Canadian Interference - Causing Equipment Regulations. ® , the stylized X, XDL23, XDL33, XDL33D, and identifying product names and...
Page 3
Introduction Welcome Congratulations on acquiring your new XEROX copier. The features, ease of operation, and reliability of your copier allow you to concentrate on your business and leave the copying to your new XEROX copier. Supplies To order supplies for your copier, contact your local dealer or call XEROX SupplyNet at 1-800-822-2200.
Copier right side... 10 Identifying the internal parts... 11 Identifying the control panel components ... 12 About the copier information system ... 16 Message display (XDL23/XDL33)... 16 Message display (XDL33D) ... 17 Copier diagram ... 18 Labels ... 18 Normal copy mode ... 19 Power saver mode...
Page 6
Toner cartridge yield ... 77 Cleaning the document glass and cover ... 78 Adding staples ... 79 Cleaning the ADF/DADF belt... 81 Problem sol ving ..82 Problem solving charts ... 83 General ... 83 Misfeeds... 84 ... 58 XDL23/XDL33/XDL33D User Guide...
Page 7
Copy quality ... 85 XDL33D problem solving messages ... 86 Status code list ... 87 Clearing the status codes ... 89 A1-A3 (XDL23/XDL33) ... 89 A1-A3 (XDL33D) ... 91 C1-C4, C8 ... 93 C9 ... 95 E1-E3 ... 96 F1... 98 F9...
Page 8
Table of contents NOTES: XDL23/XDL33/XDL33D User Guide...
Do not place the copier near or over a radiator or heat register. Do not place the copier in a built-in installation unless proper ventilation is provided.
Page 10
Ozone: This product produces ozone during normal operation. The produced ozone depends on the copy volume, and the produced ozone is heavier than air. Providing the correct environmental parameter, such as specified in the XEROX installation procedures, ensures that the concentration levels meet the safe limits.
How to obtain Another paper tray different in size XDL23/XDL33/XDL33D User Guide In order to obtain another paper tray for a different paper size, or to obtain instructions on how to adjust your paper tray, contact your local dealer. Additional paper trays are available in the following sizes: 5.5x8.5in.SEF...
Most information applies to all models. When information applies to a specific model, the model number is shown in parentheses following the unique information. Some copier models may have optional accessories. Any one or more of these accessories may or may not be installed on your copier model.
Page 13
1 sided 1 sided implies that the originals or copies have an image on one side only. 2 sided 2 sided implies that the originals or copies have an image on both sides. XDL23/XDL33/XDL33D User Guide...
Store copy paper on a flat surface in a dry area and in an enclosed cabinet. Tightly wrap any partially used reams of paper. For reliable copier operation and copy quality, XEROX recommends the following: Place your copier in a well-ventilated room.
200mm 62.3 in. 18.5 in. 15.7 in. 55.7 in. XDL23/XDL33/XDL33D User Guide When choosing a new location, specific floor requirements must be met in order to allow room for service. Consider the following guidelines: The new location must provide minimum clearances around the copier.
The following copier components are discussed: External parts Control panel Internal parts Information system Copier Document cover switch Storage Space Serial number (at rear of copier) Control panel Front cover Tray 1 Tray 2 Tray 3 XDL23/XDL33/XDL33D User Guide...
Page 17
ADF (available on some models) 10-bin sorter (available on some models) XDL23/XDL33/XDL33D User Guide Copier DADF (XDL33D) Power on/off switch Tray 5 (available on some models) Getting to know your copier Serial number (at rear of copier) Control panel Front...
Note: To select a feature in the added feature area, press the button below the feature. Special features: Select this feature to access, view, or change the copier default settings. Stapling: Select this feature to automatically staple and collate copy sets; the copy sets are delivered to the sorter/stapler.
Page 21
Tray 5 (available on some models): Select this option when using copy paper from tray 5. Message display: This area displays the following information: copy quantity, icon messages (for XDL23/XDL33) or word messages (for XDL33D), or instructions about the copier operation, copier maintenance, and status codes.
Page 22
(R/E) ratio. reduce/enlarge (R/E) ratio; each press of the button increases or decreases the percentage in 1% increments. XDL23/XDL33/XDL33D User Guide...
Page 23
Clear button: Press this button in order to clear the copy quantity. Clear All button: Press this button in order to clear all current copier selections. Stop button: Press this button in order to stop the operation of the copier.
1. Message display 2. Copier diagram Message display (XDL23/XDL33) The XDL23/XDL33 copier message display above provides the main source of information to you. It displays the copy quantity, provides you with icon information on the copier maintenance and operation. It also displays status codes that assist you with fixing a copier problem.
The current paper tray that is being used has a paper misfeed. Clear the misfeed. There is a paper misfeed inside the copier or in the paper exit area. Clear the misfeed. Turn the original clockwise. Select a reduce or enlarge ratio.
Getting to know your copier Copier diagram XDL33D The copier diagram illustrates the various areas of the copier and contains various location indicators. When a location indicator lights, it informs you of an area that requires attention. The location indicators provide information on the following...
"Please wait...Copier warming up" appears on the message display. During the warm up cycle, the copier does not respond to the Start button. Copying may begin when the message "Ready to Copy" appears on the message display; this message indicates that the copier is in the normal copy mode.
Start button, and the copier enters the warm-up cycle. For detailed information on your specific copier model, refer to the appropriate copier model below. XDL23/XDL33 When the XDL23/XDL33 power saver mode occurs, this symbol " " appears in the copy quantity area of the message display.
ADF/DADF 10-bin sorter stapler Note: Humidity curls paper, and curled paper may cause jams and copy quality problems. For reliable copier operation and good copy quality, XEROX recommends the following: Store paper: on a flat surface. in a low humidity area.
Additional paper tray sizes available, call your local dealer. ** “Other” indicates that odd-size papers can be accommodated. *** XEROX recommends the use of labels and transparencies which are designed for copiers (high temperatures) only. The paper specification chart provides information about the paper size and paper feed direction for each paper tray.
Paper capacity Copy quantity Labels and transparencies Bound books or magazines XDL23/XDL33/XDL33D User Guide This specification chart provides information about the paper types which may be used with the ADF/DADF multisheet feeder. Note: ADF (available on some models) DADF (XDL33D) DADF 5.5x8.5in./A5 to 11x17in./A3...
5.5x8.5in./A5 to 10x14in./B4 15 sheets max 11x17in./A3 10 sheets max Paper size Stapled sheet capacity 5.5x8.5in./A5 to 15 sheets max 8.5x11in./A4 8.5x14in./216x355mm to 15 sheets max 10x14in./B4 11x17in./A3 10 sheets max Paper weights 16-24lb/60-90gm Paper weights 16-24lb/60-90gm XDL23/XDL33/XDL33D User Guide...
Loading the paper trays Paper trays 1, 2 and 3 XDL23/XDL33/XDL33D User Guide When making copies, you can add paper to any tray that is not in use. When a paper tray is empty, the paper tray indicator flashes until the tray is loaded with paper.
LEF. To change the paper size of a tray, contact your local dealer. Procedure: 1. Pull open the paper tray. 2. Place the copy paper into the tray. Note: Do not fill the tray above the MAX line. 3. Close the paper tray. XDL23/XDL33/XDL33D User Guide...
4. Place only the recommended amount of copy paper into the tray. Ensure the copy paper is placed along the paper guide, gently slide the stack into the copier until the stack stops. Note: Do not fill the tray above the MAX line.
4. Fan a small stack of the special paper stock before loading it in the Bypass Tray. 5. Place the small stack of the special paper stock onto the tray, along the paper guide, and then gently slide the sheet into the copier until it stops. XDL23/XDL33/XDL33D User Guide...
Switching the paper trays XDL23/XDL33/XDL33D User Guide Change the paper size of a tray by ordering an additional paper tray that is set to another size and placing that tray into your desired tray location. To order another paper size tray contact your local dealer.
For reliable copier operation, use originals within the following ranges: Paper weight range: 16 to 24 lb. (60 to 90 gsm) Paper size range: 5.5 x 8.5 inch to 11 x 17 inch (A5 to A3) unusual size paper clips XDL23/XDL33/XDL33D User Guide...
Using the document glass XDL23/XDL33/XDL33D User Guide You can use the document glass to make a copy of a delicate or damaged original or to make copies of a reliable original. Note: The ADF is available on some models, the DADF is available with the XDL33D model only.
(Refer to the sections entitled copying features How to use the added copying features.) 7. Enter the copy quantity. Note: 99 maximum 8. Press the Start button, See the specification chart for How to use the basic XDL23/XDL33/XDL33D User Guide...
Using the duplex automatic document feeder (DADF) XDL23/XDL33/XDL33D User Guide Use the duplex automatic document feeder (DADF) to copy a stack of 1 sided or 2 sided originals. Once the Start button is pressed, the originals feed automatically to the document glass from the DADF.
How to use the added copying features.) 6. Enter the copy quantity. Note: 99 maximum for 1 1 and 2 1 copying 30 maximum for 1 2 and 2 2 copying 7. Press the Start button, How to use the basic XDL23/XDL33/XDL33D User Guide...
Using the bypass tray XDL23/XDL33/XDL33D User Guide Use the bypass tray to run short copy jobs, to use a different copy paper size, or to copy onto special paper stock. For detailed information on how to load copy paper into the...
Page 44
Note: Do not fill above the MAX line. 7. If required, select the desired basic copying features. (Refer to the section entitled copying features.) Note: When using the bypass tray the following copier features become inactive: Added copying features Reduce/enlarge auto option Original copy feature 8.
How to use the basic copying features XDL23/XDL33/XDL33D User Guide How to use the basic copying features With the copier default settings you can make copies by loading originals, entering the copy quantity, and pressing the Start button. Before pressing the Start button, you can select various basic copying features that will enhance your copy jobs.
Auto Note: When one of the paper size indicators below becomes lit, it informs you of the paper size that is in your tray selection. When an odd-paper size tray is selected the question mark becomes lit. XDL23/XDL33/XDL33D User Guide...
XDL23/XDL33/XDL33D User Guide How to use the basic copying features Manual Select this option when you require a specific paper tray. This option has the following selections: Bypass tray, Tray 1, Tray 2, Tray 3, Tray 5 , Note: Paper tray 5 is available on some models.
How to use the basic copying features Auto Select this option when you desire the copier to select the appropriate paper tray size. The automatic tray selection depends on the size of the original and the selected reduce/enlarge ratio. Note: With this option you cannot select the reduce/enlarge auto option.
Reduce/enlarge XDL23/XDL33/XDL33D User Guide How to use the basic copying features Use this feature to reduce or enlarge the image on the copies. This feature has the following options: Auto Preset Variable...
How to use the basic copying features Auto Select this option when you desire the copier to automatically select the reduce/enlarge ratio to match the selected paper size. Procedure: 1. Ensure your originals are loaded in the appropriate copier location.
XDL23/XDL33/XDL33D User Guide How to use the basic copying features Preset The preset set option provides you with five preset ratios. Select a preset ratio when your copy job requires one of the five following reduce/enlarge ratios (refer to the preset ratio...
3. If required, select the desired basic and/or added copying features. (Refer to the sections entitled copying features How to use the added copying features.) 4. Enter the copy quantity. 5. Press the Start button, , to the desired How to use the basic XDL23/XDL33/XDL33D User Guide...
Copy density XDL23/XDL33/XDL33D User Guide How to use the basic copying features Originals may be poor in quality or printed on colored paper. Use this feature to improve the copies of these documents. This feature has the following options: Exposure mode...
3. If required, select the desired basic and/or added copying features. (Refer to the sections entitled basic copying features copying features.) 4. Enter the copy quantity. 5. Press the Start button, How to use the How to use the added XDL23/XDL33/XDL33D User Guide...
XDL23/XDL33/XDL33D User Guide How to use the basic copying features Manual Select the manual mode when your originals mainly contain text. The manual mode allows you to adjust the background areas to your desired copy density. Procedure: 1. Ensure your originals are loaded in the appropriate copier location.
How to use the basic copying features Auto exposure When the auto exposure mode is selected the copier automatically adjusts the copy contrast to the copy density of the original. Use this option when copying originals with a colored or dark background.
XDL23/XDL33/XDL33D User Guide How to use the basic copying features Copy lighter/darker You can vary the copy contrast of your copies in small increments. Select this option to lighten or darken the contrast of your copies. Procedure: 1. Ensure your originals are loaded in the appropriate copier location.
How to use the basic copying features Original copy (XDL33D) The XDL33D copier allows you to use 1 or 2 sided originals to create either 1 or 2 sided copies. This feature has the following options: 2 1 two-sided to one-sided...
Page 59
XDL23/XDL33/XDL33D User Guide How to use the basic copying features Select this option when you are copying 2-sided originals to 1- sided copies. Procedure: 1. Ensure your originals are loaded in the DADF. 2. Press the Original copy button, 3. If required, select the desired basic and/or added copying features.
Page 60
3. If required, select the desired basic and/or added copying features. (Refer to the sections entitled copying features How to use the added copying features.) 4. Enter the copy quantity. 5. Press the Start button, , to 2 2, How to use the basic XDL23/XDL33/XDL33D User Guide...
Page 61
XDL23/XDL33/XDL33D User Guide How to use the basic copying features Select this option when you are copying 1-sided originals to 2-sided copies. Procedure: 1. Ensure your originals are loaded in the DADF. 2. Press the Original copy button, 3. Enter the number of the originals.
Page 62
3. If required, select the desired basic and/or added copying features. (Refer to the sections entitled copying features How to use the added copying features). 4. Enter the copy quantity. 5. Press the Start button, , to 1 1, How to use the basic XDL23/XDL33/XDL33D User Guide...
Manual 2 sided copying XDL23/XDL33/XDL33D User Guide How to use the basic copying features Copiers which are equipped with an ADF can produce multiple 2 sided copies from 1 sided originals. The ADF is available on certain models; for more information, call your local dealer.
Page 64
10. Select the paper tray which contains the reordered, even-numbered copies. 11. Select the same copy quantity as you did in Step 5. 12. Press the Start button, 13. Remove your 2 sided copies from the output device. XDL23/XDL33/XDL33D User Guide...
Job interrupt XDL23/XDL33/XDL33D User Guide How to use the basic copying features Select this feature when you need to interrupt the job you are running to perform a different job, and desire to go back to the first running job without reprogramming it.
How to use the added copying features How to use the added copying features Along with the basic copying features, the XDL23/ XDL 33/ XDL 33D copier also provides additional copying features you can include with your copy jobs. This section provides detailed information on how to use the added copying features.
Special features Select this feature to access, view or change the factory default settings. For detailed information about each of the copier default settings and how to change them, refer to the section entitled Customizing your copier. XDL23/XDL33/XDL33D User Guide...
How to use the added copying features Stapling This copier operation allows you to staple copy sets that are sent to the 10-bin sorter stapler. For detailed information about the sorter bin capacity and paper specifications, refer to the sections entitled Technical data.
XDL23/XDL33/XDL33D User Guide How to use the added copying features Manual stapling Select this operation when you need to have the copy sets stapled after the copy job has been completed and the copy sets are still in the sorter bins.
For detail information on the sorter bin capacity refer to the sections entitled Paper Technical data. Note: The collated feature requires the copier to be equipped with the 10-bin sorter stapler. Procedure: 1. Ensure your originals are placed in the ADF/DADF.
Book mode XDL23/XDL33/XDL33D User Guide How to use the added copying features Select this feature to copy facing pages of a book or magazine. To change the fixed paper size of a tray, contact 1-800- TEAM XRX (1-800-832-6979). Note: The paper supply auto or the reduce/enlarge auto options cannot be activated when the book mode feature is selected.
3. If required, select the desired basic and/or added copying features. (Refer to the sections entitled copying features How to use the added copying features.) 4. Enter the copy quantity. 5. Press the Start button, Customizing How to use the basic XDL23/XDL33/XDL33D User Guide...
Edge deletion XDL23/XDL33/XDL33D User Guide How to use the added copying features Select this feature to delete unwanted images on the edge of a copy (example: punched holes). Note: The factory default is set to a 10mm edge deletion. To change the default, refer to the section entitled Customizing your copier.
Identifying the special features Special feature Tray This default sets the tray that is selected when the copier is in the normal copy mode or when the Clear all button is pressed. Automatic clear This default allows you to activate or deactivate the time (60 seconds) it takes the copier to return to the normal copy mode after the copy cycle is complete.
Page 75
Special feature Reduce/enlarge This default sets the reduce/enlarge ratio that is selected when the copier is in the normal copy mode or when the Clear all button is pressed. Original size This default sets the paper tray that is used when no original size is detected by the paper supply auto or reduce/enlarge auto options.
4. Press the Paper supply button, 5. Press the Start button, 6. Press the Special features button, ,or the Clear all button, program the setting and exit to the normal copy mode. , to the desired tray. , to XDL23/XDL33/XDL33D User Guide...
Program Special feature name Option Original Size XDL23/XDL33/XDL33D User Guide Customizing your copier Instructions on how to change the setting 1. Press the Special features button, 2. Enter the program number. 3. Press the Start button, 4. Press the Paper supply button, , and watching the size LED, select the desired original size.
3. Press the Start button, remaining copy life of the cartridge is displayed on the message display. 4. Press the Special features button, or the Clear all button, the normal copy mode. , to , to exit to XDL23/XDL33/XDL33D User Guide...
Program Special feature name Option Power saver Density mode Edge delete Margin shift Reduce/enlarge XDL23/XDL33/XDL33D User Guide Instructions on how to change the setting Number Selection 1. Press the Special features button, deactivate 4min. 2. Enter the program number. 6min.
Total copy counter Total copy counter The XDL23/XDL33/XDL33D copier is equipped with a total copy count meter. The counter allows the operator to access the total number of copies made on the copier. To view the total number of copies made, open the front cover and locate the total copy counter.
Copier care Ordering supplies Replacing the drum cartridge XDL23/XDL33/XDL33D User Guide To order supplies for your copier, contact your local dealer or (in the US and Canada) XEROX supply net toll free at: 800-822-2200 Toner cartridge: 6R918 Drum cartridge: 13R555...
Page 82
5. Hold onto the drum cartridge handle and slide the cartridge out of the copier. Note: Help the environment by recycling your used drum cartridge. Refer to the XEROX green team brochure packed with the drum cartridge for instructions on how to return the used cartridge to XEROX .
6. Slide the cartridge out gently. Note: Help the environment by recycling your used toner cartridges. Refer to the XEROX green team brochure packed with the toner cartridges for instructions on how to return the used cartridges to XEROX . Copier care...
Page 84
Note: You can not rotate the cartridge until it is pushed in all the way. 12. Remove the sheet of paper on the copier front cover. 13. Switch the copier on. 14. Ensure the toner indicator is off, Note: If the toner indicator did not turn off, do not pull the cartridge out and try to reinsert it.
The size of the document being copied. Dark backgrounds. Leaving the platen cover open. The number of times the copier is switched on and off. Double sided copying will use more toner per ream of paper. High humidity. To get the most from your toner cartridge: Always copy with the document cover closed.
Cleaning the document glass and cover Keeping the document glass and document cover clean helps ensure the best possible copies. XEROX suggests that you clean the document glass at the start of each day and during the day as needed.
To order staples for your copier, (in the United States and Canada) call XEROX SupplyNet toll at: 1-800-822-2200 Procedure: Note: XEROX recommends that you use staples which are designed for the 10-bin sorter stapler (reorder part number 8R7907). 1. Switch the copier off.
Page 88
10. Position a sheet of paper along the front edge of the top bin. 11. Press the Manual stapler button, paper is stapled properly. Note: If needed, press the Manual stapler button, , repeatedly until the stapler operates. . Ensure the XDL23/XDL33/XDL33D User Guide...
Cleaning the ADF/DADF belt XDL23/XDL33/XDL33D User Guide Keeping the ADF/DADF belt clean helps prevent ADF/DADF misfeeds. XEROX suggests that you clean the belt as needed. Note: This procedure is for copiers which are equipped with the ADF/DADF. Caution: Do not pour or spray water directly on the belt.
Problem solving Problem solving This section provides you with copier problems that may occur, their recommended solutions, and other information to assist you when solving problems. The following topics are discussed: Problem solving charts XDL33D problem solving messages Status code list...
Copies are not copied on the desired paper size. XDL23/XDL33/XDL33D User Guide The problem solving charts list copier problems that may occur and their suggested solutions. Follow the suggested solutions until the problem is corrected. If the problem persists, call for service.
Documents misfed repeatedly when using the ADF/DADF. Misfeeds Suggested solutions If a status code appears (XDL23/XDL33) or a message (XDL33D), refer to the appropriate section entitled Clearing the status codes (XDL23/XDL33) problem solving messages (XDL33D). Ensure the paper trays and bypass trays are firmly in place.
Page 93
Problem Copies appear dark. Copies are light overall. Copy images are partially deleted. Copy images are distorted or skewed. XDL23/XDL33/XDL33D User Guide Suggested solutions Clean the document glass. Ensure the proper exposure mode is selected, refer to the section entitled How to use the basic copying features.
Clearing the status solve the copier problem. Note: When the status code appears, use the first two characters to identify the status code. (Example F1-1, you would go to the F1 status code procedure.) codes to XDL23/XDL33/XDL33D User Guide...
Clearing the status E1-E3 There is a paper misfeed inside the copier or in the paper exit area, refer to the E1-E3 status code procedure in the section entitled The copier front cover is open. Close the cover. The copier right upper or right lower cover is open. Close the cover.
Page 96
J7, drum cartridge, 13R555 is installed. XEROX card or key counter is not loaded. Install the XEROX card or key counter. U1-U4, U6-U8 Switch the copier off. Wait approximately one (1) minute, then switch the copier on. If the status code continues, call for service.
Clearing the status codes XDL23/XDL33/XDL33D User Guide Refer to the appropriate procedure to clear the displayed status code. If the problem persists, call for service. A1-A3 (XDL23/XDL33) A codes appear whenever the ADF has trouble feeding an original. 1. Raise the original catch tray.
Page 98
Make a new copy of any damaged original. 13. Ensure the ADF guide is touching the edge of the originals. 14. Lower the original catch tray. 15. Ensure the Ready to copy lamp on the ADF is lit. XDL23/XDL33/XDL33D User Guide...
XDL23/XDL33/XDL33D User Guide A1-A3 (XDL33D) A codes appear whenever the DADF has trouble feeding an original. 1. Open the left DADF cover. 2. Remove any misfed original. 3. Open the left inside cover. 4. Raise the original catch tray. 5. Remove all the originals.
Page 100
Make a new copy of any damaged original. 16. Ensure the DADF guide is touching the edge of the originals. 17. Lower the original catch tray. 18. Ensure the Ready to copy lamp on the DADF is lit. XDL23/XDL33/XDL33D User Guide...
XDL23/XDL33/XDL33D User Guide C1-C4, C8 C codes appear whenever the copier has trouble feeding a sheet of paper from a paper tray. For XDL23/XDL33/XDL33D 1. If one of the right cover indicators is flashing, open the appropriate cover. Note: If the paper is not accessible from the right upper cover opening, open the copier front cover and remove the misfed paper.
Page 102
Open the metal cover (on left side of tray). Remove any misfed paper. Close the metal cover. Open the plastic cover (on right side of tray). Remove any misfed paper. Close the plastic cover. Close tray 4. XDL23/XDL33/XDL33D User Guide...
Page 103
2. Open the copier front cover. 3. Lift up on the copier release lever and open the copier. 4. If there is any misfed paper inside the copier, pull it out toward the copy output device. 5. Close the copier.
1. Open the copier front cover. 2. Lift up on the copier release lever and open the copier. 3. If the lead edge of the misfed paper is accessible from the copy output tray, pull the paper out toward the tray.
Page 105
6. If the misfed paper is shown in the figure to the left, pull it out toward the copy output tray. 7. Open the copier right upper cover or right lower cover, remove any misfed paper. 8. Close the copier.
Page 106
1. Pull back the sorter release lever, then slide the sorter to the left until it stops. 2. Remove any misfed paper in the exit area of the copier. 3. Remove any misfed paper in the sorter. 4. Pull back the sorter release lever and slide the sorter to its original position.
Page 107
XDL23/XDL33/XDL33D User Guide F codes appear whenever the 10-bin sorter stapler has trouble with the stapler or trouble with feeding paper. The F9 code appears when there is a problem with the sorter stapler. 1. Remove all paper from the sorter bins.
Page 108
9. Position a sheet of paper along the front edge of the top bin. 10. Press the Manual stapler button, the paper is stapled properly. Note: If needed, press the Manual stapler button, , repeatedly until the stapler operates. , and ensure XDL23/XDL33/XDL33D User Guide...
Before moving the machine unlock the four castors and then relock the castors after placing the machine to the new location. If you need to relocate the machine to a different floor level (example: up the stairs), XEROX recommends that you call your local dealer. Problem solving...
64%, 77%, 100%, 129%, 154% Variable: 61%-163% 99 copies 99 copies for 1 1 and 2 1 copying 30 copies for 1 2 and 2 2 copying 250 sheets 250 sheets 250 sheets 30 sheets 1000 sheets 50 sheets XDL23/XDL33/XDL33D User Guide...
Page 111
Power consumption Machine dimensions XDL23/XDL33 XDL33D XDL23/XDL33 with ADF XDL33D with DADF XDL23/XDL33 with ADF and 10-bin sorter stapler XDL33D with DADF and 10-bin sorter stapler 1 tray module (Stand - XDL23/XDL33) 2 tray module (Stand - XDL23/XDL33) Duplex module (Stand - XDL33D)
Page 112
XDL33 XDL33D XDL23 with ADF XDL33 with ADF XDL33D with DADF XDL23 with ADF and 10-bin sorter stapler XDL33 with ADF and 10-bin sorter stapler XDL33D with DADF and 10-bin sorter stapler 1 tray module (Stand - XDL23/XDL33) 2 tray module (Stand - XDL23/XDL33)
Page 113
10-bin sorter stapler Top bin sheet capacity staple capacity Bins 2-10 sheet capacity staple capacity Dimensions Weight Power XDL23/XDL33/XDL33D User Guide 5.5x8.5in./A5 to 11x17in./A3 16-24lb./60-90gm² 50 sheet maximum 25.1in.x24.2in.x3.4in./640x615x86mm 35.24lbs./16kg 120 watts or less 100 sheets of 5.5x8.5in./A5 to 11x17in./A3 16-24lbs./60-90gm²...
Repair Is Your Only Remedy Your only remedy under limited warranty is the repair of your copier as described herein. Xerox will not be liable for any incidental or consequential damages resulting from your use of, or inability to use, your copier even if we know such damages are possible.
Page 115
90 day limited warranty If You Have a Problem The first step is to call the Xerox Authorized Dealer from whom you purchased your copier. Your Xerox Authorized Dealer, if service authorized, is responsible for your satisfaction and equipment repairs for copiers sold in his/her local service authorized territory. If the unit is in an area not serviced by the Xerox Authorized Dealer, then call the Xerox Customer Support Representative at 1-800-TEAM- XRX (1-800-832-6979).
Copyright Office, Library of Congress, Washington, D.C. 20550, or telephone the Copyright Office at (202) 707-9100 and ask for circular 21. Copying of other items may be prohibited. If you have any questions, seek legal advice. XDL23/XDL33/XDL33D User Guide...
Xerox Authorized Dealer Total Satisfaction Guarantee At Xerox, we are committed to the highest quality in the design, manufacturer and service of what we sell. We measure our success by one standard: Total Customer Satisfaction. Taking this commitment one step further, we now offer this exclusive Xerox Total Satisfaction...
Material safety data sheet Material safety data sheet XDL23/XDL33/XDL33D User Guide...
Page 119
Material safety data sheet XDL23/XDL33/XDL33D User Guide...
Page 120
Material safety data sheet XDL23/XDL33/XDL33D User Guide...
Page 121
Material safety data sheet This MSDS may not be the latest version. To obtain the latest version you may call 1-800-828-6571, or visit their Web site at: http://ids.xbs.xerox.com/ehs/msds/ XDL23/XDL33/XDL33D User Guide...