Table of Contents
Advertisement
aa
TTT
gD
ae
nen
nN
* When you select this parameter, the Monitor indicator will
blink. To execute the selected type of bulk dump, press the
Enter button.
* Since a large volume of data is transmitted, you should first
check the memory capacity of the receiving MIDI device
before you execute the bulk dump. If there is insufficient mem-
ory to receive the data, transmission will be interrupted. If all
data is transmitted, the M-GS64 transmits a bulk dump of
approximately 26 Kbytes.
* Be aware that if MIDI OUT/THRU
Select is set to THRU, the
data will not be transmitted.
@ Prevw Noje (Preview Note Name) : C-1 - G9
This sets the note that will be sounded by the Preview function
(p. 20). The 'A' note in the center of the keyboard is A4.
* If the Key Shift parameter has been set, the pitch will be shift-
ed.
:
@ Prevw Velo (Preview Velocity) : 0 - 127
This sets the velocity value of the note that will be sounded by
the Preview function. Normally, higher velocity values will
result in a louder volume.
@ SysOutMode (System Output Mode)
: Selected/Fixed
This determines whether the Output Assign setting (p. 10) will
be valid or not.
Selected The sound of each Part will be output as specified by
the Output Assign settings.
The output of each Part will be fixed as follows, regard-
less of the Output Assign settings.
Fixed
For Mode 1:
Both Parts A and B wil) be output in stereo with the
effect sound from the Output 1 jacks.
Outputt (Includes effects)
For Mode 2:
The Parts of group A will be output in stereo with the
effect sound from the Output 1 jacks, and the Parts of
group B similarly from the Output 2 jacks.
A Part ———
Outputi (Includes effects)
B Part —-—-» Output2 (includes effects)
In this case only, the Output 2 jacks will output sound
that includes the effect sound.
18
* The headphone jack will output the sound that is sent to
Output 1. This means that the sound of the Parts assigned to
Output 2 will not be heard in the headphones.
" At the factory settings, this parameter is set to "Selected."
@ OUT/THRU
(MIDI OUT/THRU
Select) : OUT/THRU
The "MIDI OUT/THRU" connector located on the back panel of
the M-GS64 functions either as a MIDI OUT or a MIDI THRU.
When the OUT/THRU Select parameter is set to OUT the con-
nector functions as MIDI] OUT, and when set to THRU
it func-
tions as MIDI THRU.
THRU: Data received at MIDI IN A is retransmitted from MIDI
OUT/THRU without change. Data received at MIDI IN B
will not be thru-ed even if THRU
is selected. Also,
regardless of the In Mode setting, MIDI IN B data will not
be thru-ed.
OUT: Exclusive data can be transmitted from the MIDI
OUT/THRU connector.
* When you change this setting, the display will blink. In order
to make the new setting valid, you must turn the power on
once again.
@ Mute Lock : On/Off
When you re-play song data that has already been played back,
Mute settings (p. 6) that you made may sometimes be canceled.
This happens because the beginning of the song contains data
that resets the M-GS64 (General MIDI System On, GS Reset). If
you turn Mute Lock on, the Mute settings will not be Jost even if
GS Reset or General MIDI System On messages are received, so
you will not need to reset the Mute settings.
@ EQ Lock (Equalizer Lock) : On/Off
When a GS Reset or General MIDI System On message is
received, the equalizer settings will normally be reset to the fac-
tory settings. However if the EQ Lock is on, the equalizer set-
tings will be preserved.
@ Out Asgn Lock (Output Assign Lock) : On/Off
The Output Assign and System Output Mode settings will nor-
mally be reset to the factory settings when a GS Reset or GM
System On messages are received. However if Out Assign Lock
is on, these settings will not change.
@ Rx Mode (Rx Sys Mode: System Mode Receive Switch) :
On/Off
The selection of either Single Module Mode or Double Module
Mode (p. 8) is referred to as the System Mode. The Rx Sys Mode
parameter is the receive switch for MIDI messages (System
Mode Set, p. 42) that switch the System Mode. If Rx Sys Mode is
turned off, the mode will not change when a System Mode Set
message is received. If it is turned on, the made will change.
Advertisement
Table of Contents
