Advertisement
VARIOUS OPERATIONS
To search for the peak volume level within
a
|
With this function, the peak level of CD can easily be searched
for. This is convenient for adjusting the proper recording level.
To search for the peak level of the entire disc:
During stop mode, press PEAK SEARCH.
@
The player scans the entire disc and searches for the peak level.
Ittakes about 1 minute with a 60-minute CD. While searching,
the PEAK indicator blinks on the display.
e
To cancei the peak search function, press @.
To search for the peak level of the programmed tracks:
Pragrarn the desired tracks beforehand and press PEAK SEARCH.
The player scans ail of the programmed tracks and searches for the
peak level between them.
To adjust the recording level
1. When the piayer detects the peak level, a 6-second (approximate)
portion of the disc including the peak level is played repeatedly.
2. Adjust the recording level on the tape deck.
3. Set the tape deck to recording mode and start CD play by
pressing ».
1
mo
2
ji
a
(PD-202)
Ve
PD.102
i
ce
Ce
AS
NOTES:
@
Theplayersometimes detects the different peak level even when
the peak search function is carried out an one disc.
@
With some discs, the player cannot detect the proper peak level.
This is not a malfunction.
e@ When the peak level exists an the beginning or end of the track,
the section which contains the peak fevel is played repeatedly for
about 3 seconds.
Sf 9 (PD-202)
Press OUTPUT LEVEL "—" or "+" to adjust the output level.
e@ The output level can be adjusted between 0 dB and -25 dB in
steps of 1 dB.
@
The ATT display shows the selected level.
@ The output level at the OUTPUT jacks and PHONES jack will be
adjusted simultaneously,
@
If the disc is in the player, the setting of the OUTPUT
LEVEL
button is not erased even when the power is turned off
However, if the power is turned off with an audio tirner or by
unplugging the power cord, the setting of the OUTPUT LEVEL
button will be erased
co
ts gH (PD-202)
(PO-202)
| Program playback - To program tracks in
desired order
Pragramming is possible during stop or playback mode.
Only during stop mode, the dialog display appears in each step to
facilitate programming.
1 Press PROGRAM.
@ "TRACK?" appears on the display
2 Enter the desired track numbers in a desired order
with the digit button.
®
Up to 24 tracks (steps) can be programmed.
3 Press &.
The tracks are played in the programmed
order.
When
all
prograrnmed tracks have been played, the player enters stop
mode
To stop Program playback, press B.
@ Togo to the previous or next step in a program, press Kid <<
(OF ft} OF Be ed (Or Bi),
@
Each time a track is programmed, the display. will show the
programmed number
e@ If the disc is in the player, the program contents will not be
erased even if the power is turned off.
Programming while listening to playback
During norma! playback or program playback, you can program the
desired tracks.
During
normal
playback
or Hi-Lite sean
playback
(Direct
program):
The track being played can be programmed.
1. During playback, press PROGRAM to enter the program mode
2. Whenever a irack to be programmedis played, press PROGRAM,
You can repeat step 2 until up to 24 steps are programmed
3. After programming, press ®. The current playback is cleared and
the tracks are played in the programmed order,
During program piayback:
Enter the desired tracks without pressing PROGRAM.
The program
contents are added to the prograrn being played
Notes on time display
@
ff the total playing time ar total remaining time exceeds
100
minutes, the corresponding time will not be displayed.
®
ff track No. 30 or above is programmed, total remaining time or
total playing time will not be displayed.
iS]
<PRB1182>
En
Advertisement
