DeWalt DXV30SAPTA Original Instructions Manual page 10

EN
WARNING: Use the vacuum cleaner's socket
outlet only for connection of an external power tool.
The vacuum cleaner is automatically switched on
and off via the connected power tool.
The connected load of the power tool may not
exceed the maximum connected load PA of the
vacuum cleaner's socket outlet. Please also observe
the operating instructions and safety warnings of the
power tool being connected to the socket outlet of
the vacuum cleaner.
RECOMMENDATION: Always operate the vacuum
cleaner via a residual current device (RCD) with
a rated residual current of 200mA or less. Please
ensure that the power tool switch is in the 'Off'
position before connecting the tool to the vacuum.
After switching off a power tool connected to
the vacuum cleaner's socket outlet, the vacuum
cleaner will run on for approx. 15 seconds and then
automatically switch off.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. lf operating a power tool in a damp location
is unavoidable, use a residual current
device(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
7. The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate. lf
the supply cord is damaged, it must be replaced
only by DEWALT or an authorised service
organisation.
MAINS PLUG REPLACEMENT
(U.K.&IRELAND ONLY)
lf a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the
plug.
• Connect the blue lead to the neutral terminal.
• Connect the yellow/green lead to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13A.
WARNING: Never use a light socket. Never
connect the live (L) or neutral (N) wires to the earth
pin marked E or.
USING AN EXTENSION CABLE
lf an extension cable is required, use an approved
3-core extension cable suitable for the power input
of this tool (see Technical Data). The minimum
conductor size is 1.5 mm²; the maximum length is
30 m. When using a cable reel, always unwind the
cable completely.
BLOWING FEATURE (Fig. C)
WARNING: To avoid injury to bystanders, keep
them clear of blowing debris.
The vacuum contains a blowing feature. It has the
capability to blow sawdust and other debris. It can be
used to blow dust and debris out of garages or off
patios and driveways. Follow the steps below to use
the vacuum as a blower.
1. Locate blowing port on the vacuum.
2. Insert one end of the hose into the blowing port.
3. Turn vacuum "ON".
STORAGE (Fig. A)
1. Empty dust tank, refer to TO EMPTY DUST TANK
instructions.
2. Clean the vacuum inside and outside. refer to
CLEANING.
3. Clean or replace filters, refer to FILTER.
4. Store the hose and the power cord, as shown in
the Fig. A. Place the appliance in a dry room and
secure it from unauthorized use.
OPTIONAL ACCESSORIES
WARNING: Since accessories, other than those
offered by DEWALT, have not been tested with this
product, use such accessories with the appliance
could be hazardous. To reduce the risk of injury, only
DEWALT recommended accessories should be used
with this product.
CLEANING
To keep the wet/dry vacuum looking its best, clean
the outside with a cloth dampened with warm water
and mild soap.
To clean the tank:
1. Dump out debris.
2. Wash tank thoroughly with warm water and mild
soap.
3. Wipe with dry cloth.
10