Bosch Professional GWX 18V-10 P Instructions Manual page 24

24 | English
Technical data
Angle Grinder
Article number
Rated voltage
A)B)
Rated no-load speed
Max. grinding disc dia-
meter/rubber sanding pad
diameter
KickBack Control
Restart Protection
Run-out brake
Drop Control
Weight according to EPTA-
C)
Procedure 01:2014
Recommended ambient
temperature during char-
ging
Permitted ambient temper-
D)
ature during operation
and during storage
Recommended re-
chargeable batteries
Recommended chargers
A) Rated no-load speed for the selection of appropriate application
tools in accordance with EN IEC 62841-2-3. The actual no-load
speed must not exceed the rated no-load speed and is therefore
lower.
B) Measured at 20–25 °C with rechargeable battery ProCORE18V
8.0Ah and depending on the battery's state of charge as well as
the power tool's operating temperature
C) Depends on rechargeable battery (5), protective guard ((11),
(10), (14)) and auxiliary handle ((9), (8)) in use
D) Limited performance at temperatures < 0 °C
Values can vary depending upon the product and are subject to ap-
plication and environmental conditions. For further information
www.bosch-professional.com/wac.
Noise/Vibration Information
Noise emission values determined according to
EN IEC 62841-2-3.
Typically the A-weighted noise level of the power tool are:
84 dB(A); sound power level 92 dB(A). Uncertainty K =
3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN IEC 62841-2-3:
Surface grinding (roughing) and cut-off grinding:
2 2
a = 4.2 m/s , K = 1.5 m/s ,
h
1 609 92A 8XG | (04.08.2023)
GWX 18V-10 P
3 601 JJ4 2..
V= 18
–1
min 9000
mm 125
●
●
●
●
kg 2.5–3.3
°C 0 to +35
°C –20 to +50
GBA 18V... ≥ 4.0 Ah
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
a)
Disc sanding:
2 2
a = 2.8 m/s , K = 1.5 m/s .
h
a) determined with medium-hard backing pad
Grinding thin metal sheets or other materials that tend to easily vi-
brate with a large surface area can cause the noise emission value to
increase by up to 15 dB. Suitable, heavy damping mats can reduce
the increased noise emissions. Increased noise emissions must be
taken into consideration, both for the risk assessment of the noise
output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ac-
cessories or is poorly maintained, the vibration level and
noise emission value may differ. This may significantly in-
crease the vibration and noise emissions over the total work-
ing period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and accessories, keeping their hands warm, and
organising workflows correctly.
Kickback stop
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
To restart the tool, set the On/Off switch (4) to the "off" po-
sition and then switch the power tool on again.
Restart protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (4) to the "off" posi-
tion and then switch the power tool on again.
Run-out brake
The power tool is fitted with the electronic
Bosch Brake System. When it is switched off,
the abrasive tool is brought to a complete stop
within a few seconds. This means that the run-
out time is significantly shorter than for angle
grinders without a run-out brake and enables the power tool
to be set down sooner.
Impact shutdown
The integrated impact shutdown switches the power tool off
as soon as it hits the floor. To restart the tool, set the On/Off
Bosch Power Tools