Page 1
I n s t a l l a t i o n Gu i d e MX S O1 7 0 0 S a u n a S h o u l d y o u r e q u i r e a d d i t i o n a l a s s i s t a n c e wi t h t h e i n s t a l l a t i o n o f y o u r p r o d u c t , p l e a s e c a l l 0 1 9 0 8 3 1 7 5 1 2 o r e ma i l...
Page 2
www.insigniashowers.com Last Modified: 29/06/2022 INSTALLATION MANUAL MXOS1700 Outdoor Sauna Series 30 Day Technical Support: Call 01908 317512 and request technical support for aiding your installation. Replacements Parts: Inside of your warranty period visit: https://www.insigniashowers.com, click support and make a warranty claim. Spares/Replacements Parts: Outside of your warranty period visit https://www.insigniashowers.com/replacement-parts.html...
www.insigniashowers.com Last Modified: 29/06/2022 Contents Thank you for your purchase Bench seat install Electrical & Tool requirements Back rest install Box contents Installing the fixed glass panel Creating the base Installing the inner roof Installing the back right upright Installing the big roof Installing the back panel Installing the heater and heater guard Installing the back left upright...
Last Modified: 29/06/2022 Thank you for your recent purchase of an Insignia Sauna. Please read this booklet with great care to ensure you get the best out of your build and have a Sauna that will last for many years to come! Like everything, in order to obtain a first class product that will serve you well for many years, the effort and correctness put into the assembly will reflect in the quality of your finish.
www.insigniashowers.com Last Modified: 29/06/2022 Tools Required Electrics 4.5KW Power Rating • Scissors • Knife Always consult a qualified Electrician before connection as to suitability • Spirit Level Your electrical contractor will understand ALL legal requirements of connection before • Tape Measure undertaking any work or installation.
Sauna Heater Screw Pack Heater Guard VERY IMPORTANT Have you got everything? If not please contact the Insignia directly on 01908 317 512. Remember NEVER book your tradesman until everything has arrived, been checked and is present. No replacement/missing parts can be obtained free of charge during or after the build.
www.insigniashowers.com Last Modified: 29/06/2022 Step 1 — Creating the base Create a square using the 4 bottom struts. Note: The front strut has a groove cut out for the front fixed glass panel. Make sure this strut is at the front of the square.
www.insigniashowers.com Last Modified: 29/06/2022 Step 2 — Installing rear right upright There will be 3 screw connections on two faces of the upright. They should face towards the back bottom strut and right bottom strut.
www.insigniashowers.com Last Modified: 29/06/2022 Step 3 — Installing the back panel Lift the back panel and slide the brackets over the screw fixings and lock into position. Also ensure you push the panel down onto the back bottom strut and ensure they lock together.
www.insigniashowers.com Last Modified: 29/06/2022 Step 4 — Installing the back left upright Tilt the back panel up in order to get the back left upright to slot into the brackets. Connect and push the right back upright down and secure into position. There will be 3 screw connections on two faces of the upright.
www.insigniashowers.com Last Modified: 29/06/2022 Step 5 — Installing the right side panel Lift the side panel and slide the brackets over the screw fixings and lock into position. Also ensure you push the panel down onto the right bottom strut and ensure they lock together.
www.insigniashowers.com Last Modified: 29/06/2022 Step 7 — Installing the right front upright Slot the front right upright onto the side panel and push down to secure in position.
www.insigniashowers.com Last Modified: 29/06/2022 Step 8 — Installing the left side panel Lift the left side panel and slot down onto the back left upright and locking in place on the bottom left strut.
www.insigniashowers.com Last Modified: 29/06/2022 Step 9 — Installing the front left upright Slot the front left upright onto the side panel and push down to secure in position.
www.insigniashowers.com Last Modified: 29/06/2022 Step 10 — Electric box The electrical box (below) should be housed in the sauna, underneath the back bench on the floor. Install electrical connections. Partner up all corresponding wires which are denoted by matching stickers from the box to the back/ right panels.
www.insigniashowers.com Last Modified: 29/06/2022 Step 19 — Installing the top frame Locate the top framework into position. Secure loosely, as you need manoeuvrability of the framework to insert the fixed glass panel.
www.insigniashowers.com Last Modified: 29/06/2022 Step 11 — Placing the floor in position The cut-outs in each front corner go around the front uprights. Ensure you place the floor in it’s correct orientation.
www.insigniashowers.com Last Modified: 29/06/2022 Step 17 — Placing under seat support frame ST40 x 26 • Using ST40 Screws locate the large frame support to the back of the sauna. • From the inside screw the base of all bench front to the adjoining panels.
www.insigniashowers.com Last Modified: 29/06/2022 Step 18 — Placing the bench seat in position Locate the bench seat into position by placing it onto the under support frame.
www.insigniashowers.com Last Modified: 29/06/2022 Step 18 — Installing the back rests Locate the back rest and place along the back wall of the sauna. Align using a spirit level and screw I in position using ST50 Screws.
www.insigniashowers.com Last Modified: 29/06/2022 Step 20 — Installing the fixed glass panel Overhead view (right) With the framework in position tighten the nut and washer from above. Note: Be careful not to drop the hex nut and washer down the upright. Insert the fixed glass into the groove cut-outs in the framework, lift the top framework up, then slot back down once it is in position.
www.insigniashowers.com Last Modified: 29/06/2022 Step 21 — Installing the inner roof Locate the inner roof and lift into position. Once in position, take all cabling from the back and side panel and connect on top of the inner roof. Locate the thermos probe and feed through the inner roof.
www.insigniashowers.com Last Modified: 29/06/2022 Step 22 — Installing the big roof Lift the roof into position and position the square locaters into the top of all uprights. Caution: Roof is heavy, Minimum 2 person lift advised.
www.insigniashowers.com Last Modified: 29/06/2022 Step 22 — Installing the heater and heater guard Locate the heater backplate and screw into position using the screws provided in the heater box. Connect the heater hood by clipping it into the heater. Take the heater and locate it onto the backplate, resting the bottom within the grooves and securing it in position with a screw through a pre-made hole in the hood.
www.insigniashowers.com Last Modified: 29/06/2022 Step 22 — Installing the door handle Locate the door handle and separate before attaching it to the door. The metal handle is designed to be on the outside of the sauna. The door will be positioned here.
www.insigniashowers.com Last Modified: 29/06/2022 Step 23 — Installing the door Unscrew bolts and separate Side View Lift the door into position and then fix the door into the Front View hinges. To realign the door, loosen the bolts slightly, reposition and then retighten. Repeat this process until alignment is perfect.
www.insigniashowers.com Last Modified: 29/06/2022 Step 25 — Accessories Installation 40mm Screws Connect the light from the wire fed through the pre drilled hole in the back panel. Screw into position. Place a screw into the back wall and hang the Use two screws through the backplate and position hygrometer.
www.insigniashowers.com Last Modified: 29/06/2022 Control Panel Instructions Button 1 (Lights) Turn the 12V light on or off. Button 2 (Return) Press to return to the menu after a change is made. Button 3 (Mode button/Scroll) Press and hold for 3 seconds to power the panel on or off. Press to change the control panel function, then scroll left or right to change settings.
Page 30
www.insigniashowers.com Last Modified: 29/06/2022 Coloured Lights FM Radio Volume To operate the lights, press To operate the FM Scroll (Button 3) until you (Button 3) until you see the Radio, Scroll (Button see the interface (left). Once interface (left). Once here 3) until you see the here, press (Button 3) to press (Button 3) and scroll...
Page 31
www.insigniashowers.com Last Modified: 29/06/2022 Settings Scroll (Button 3) until you see the interface (left). Once here, press (Button 3) to enter the settings mode. Here you can set the clock which operates on a 24 hour system. You can also change the temperature display to Celsius or Fahrenheit.
www.insigniashowers.com Last Modified: 29/06/2022 BEFORE FIRST USE — IMPORTANT Ensure the rocks have been thoroughly washed before loading in to the heater. Ensure you place the rocks loosely between the heating elements. Don’t over fill the heater, ensure sufficient airflow can be achieved for maximum output. ...
www.insigniashowers.com Last Modified: 29/06/2022 Sauna Usage & Safety Guide When you turn it on, you MUST pour water over the rocks as it’s the vapour that creates the heat not the rocks. The rocks alone will never heat up the sauna. Failure to do this could cause the rocks to split and break. Never leave children unattended in the Sauna.
(EEE) have to fulfil certain obligations. Under the WEEE directive Insignia is considered the producer of certain products we supply and in line with the demands of the legislation we are pleased to offer the op- portunity to return these products to us for treatment and recycling.
Page 35
www.insigniashowers.com Last Modified: 29/06/2022...