Via eden low power
15” panel pc system (102 pages)
Summary of Contents for Protech Systems SG-G151
Page 1
USER MANUAL SG-G151 15” Intel Atom x7-E3950 / ® Celeron J3455 Processor ® Fanless and all-around IP66 Panel PC SG-G151 M1...
Page 2
SG-G151 ® ® 15” Intel Atom x7-E3950 / Celeron J3455 Processor Fanless and all-around IP66 Panel PC COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in Jan. 2023. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
Page 3
FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Introduction This chapter provides the introduction for the SG-G151 system as well as the framework of the user manual. The following topic is included: • About This Manual SG-G151 USER MANUAL Page: 1-1...
Chapter 1 Introduction About This Manual Thank you for purchasing our SG-G151 system. The SG-G151 is an updated system designed to be comparable with the highest performance of IBM AT personal computers. The SG-G151 provides faster processing speed, greater expandability and can handle more tasks than before.
Getting Started This chapter provides the information for the SG-G151 system. It describes how to set up the system quickly and outlines the system specifications. The following topics are included: • Package List • System Overview • System Specification • Safety Precautions Experienced users can go to Chapter 3 System Configuration on page 3-1 for a quick start.
Chapter 2 Getting Started Package List If you discover any of the items listed below are damaged or lost, please contact your local distributor immediately. Item Q’ty SG-G151 Manual / Driver DVD Quick Guide M12 Power Supply Cable SG-G151 USER MANUAL Page: 2-2...
Avoid direct sunlight exposure for a long period of time (for example, in a closed car in summer time. Also avoid the system from any heating device.). Or do not use SG-G151 when it has been left outdoors in a cold winter day. •...
• External I/O Ports Diagram • Connector & Jumper Quick Reference Table • System Main Board Component Locations • How to Set Jumpers • Setting Main Board Connectors and Jumpers • External M12 waterproof Connector SG-G151 USER MANUAL Page: 3-1...
CAUTION: Observe precautions while handling electrostatic sensitive components. Make sure to ground yourself to prevent static charge while you are working on the connectors and jumpers. Use a grounding wrist strap and place all electronic components in any static-shielded devices. SG-G151 USER MANUAL Page: 3-4...
Take special cares while you are holding electronic circuit boards by the edges only. Do not touch the mainboard components. 3.3.2 Bottom View of System Main Board Figure 3-2 Main Board Component Location (Rear View) SG-G151 USER MANUAL Page: 3-5...
2 to create one setting and shorting. You can also select to connect pins 2 and 3 to create another setting. The format of the jumper picture will be illustrated throughout this manual. The figure below shows different types of jumpers and jumper settings. SG-G151 USER MANUAL Page: 3-6...
Page 24
Chapter 3 System Configuration Jumper diagrams Jumper settings SG-G151 USER MANUAL Page: 3-7...
ASSIGNMENT ASSIGNMENT COM2(RS485) Connector Pin Assignment: ASSIGNMENT ASSIGNMENT Notes: COM2 is selectable as RS232, RS422, RS485 by BIOS setting. Default setting is RS232. Please see Chapter 5 “Advanced – Onboard Device Configuration” for selection details. SG-G151 USER MANUAL Page: 3-9...
Page 27
COM4_TX COM4_CTS COM4_DTR COM4_RI_SEL Note: COM3, COM4: Pin 9 is selectable for RI, +5V or +12V by jumper setting. Default setting is RI, please see “COM3 and COM4 PIN9 Definition Selection Guide” for selection details. SG-G151 USER MANUAL Page: 3-10...
Color Status Description Right Side LED Yellow Blink LAN Message Active No LAN Message Active Left Side LED Green 10/100Mbps LAN connection is enabled. Orange Giga LAN connection is enabled. No LAN switch/hub is connected SG-G151 USER MANUAL Page: 3-12...
Default setting is GPI every time when system AC power is re-applied from power failure state Configuration can still be kept even in S5 state unless system AC power is lost. 3.5.10 I2C WAFER JI2C1: I2C Wafer PIN ASSIGNMENT VCC5 I2C0_SCL_33 I2C0_SDA_33 JI2C1 SG-G151 USER MANUAL Page: 3-14...
Default BIOS setting is “Auto Duty-Cycle Mode”. Please see Chapter 5 or check API document for more details. 3.5.13 DC POWER INPUT CONNECTOR PWR2: DC Power Input Connector PIN ASSIGNMENT PIN ASSIGNMENT VCC12 VCC12 PWR2 Note: The voltage of input power should be 12V or 16~24V. SG-G151 USER MANUAL Page: 3-15...
Mini PCI Express is the successor of the Mini PCI card and provides an increased data throughput. The cards have a detached network interface and are equipped with one lane. They are used in particular in embedded designs or compact box PCs. SG-G151 USER MANUAL Page: 3-16...
Jumper Name: SW1 Description: Slide Switch for LVDS Resolution/Channel/Color Bit Selection SELECTION SETTING 800 x 600 1CH/18bit (Default Setting) 1024 x 768 1CH/18bit 1024 x 768 1CH/24bit 1280 x 768 1CH/18bit 1280 x 800 1CH/18bit SG-G151 USER MANUAL Page: 3-19...
Page 37
Chapter 3 System Configuration SELECTION SETTING 1280 x 960 1CH/18bit 1280 x 1024 2CH/24bit 1366 x 768 1CH/18bit 1366 x 768 1CH/24bit 1440 x 900 2CH/24bit 1400 x 1050 2CH/24bit SG-G151 USER MANUAL Page: 3-20...
Page 38
Chapter 3 System Configuration SELECTION SETTING 1600 x 900 2CH/24bit 1680 x 1050 2CH/24bit 1600 x 1200 2CH/24bit 1920 x 1080 2CH/24bit 1920 x 1200 2CH/24bit SG-G151 USER MANUAL Page: 3-21...
POWER LED+ HDD LED- JFP1 RESET BTN POWER BTN 3.5.19 HD AUDIO CONNECTOR AUDIO1: HD Audio Connector for Line In/Line Out/Mic In. ASSIGNMENT ASSIGNMENT LINE-OUT-L LINE-OUT-L HD_GND HD_GND HD_LINE-IN-R HD_LINE-IN-L HD_GND HD_GND HD_MIC1-R HD_MIC1-L AUDIO1 SG-G151 USER MANUAL Page: 3-22...
JINV1: Panel Inverter Connector ASSIGNMENT VCC12 VCC12 JINV1 LVDS_BKLCTL LVDS_BKLTEN 3.5.21 SATA 3.0 CONNECTOR SATA1: Serial ATA 3.0 Connector ASSIGNMENT SATA_TXP0 SATA_TXN0 SATA1 SATA_RXN0 SATA_RXP0 3.5.22 SATA Power CONNECTOR SATA_PWR1: Serial ATA Power Connector ASSIGNMENT VCC5 SATA_PWR1 SG-G151 USER MANUAL Page: 3-23...
SELECTION JUMPER SETTING JUMPER ILLUSTRATION 3.3V (Default Setting) Note 1: Users can change the setting according to panel specification Note 2: Please refer to PANEL INVERTER CONNECTOR for more details about pin definition of JINV1. SG-G151 USER MANUAL Page: 3-24...
Description: Voltage selection jumper for selecting PIN1, PIN29, PIN30 (LVDS_VCC) voltage of LVDS1. JUMPTER SELECTION JUMPER ILLUSTRATION SETTING 3.3V (Default Setting) JP_VDD1 JP_VDD1 Note: Please refer to PANEL INVERTER CONNECTOR for more information about pin definition of JINV1. SG-G151 USER MANUAL Page: 3-25...
Normal (Default Setting) Clear CMOS* 3.5.27 USB POWER SOURCE SELECTION Jumper Name: JP_USBSW1 Description: USB Power Source Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION S5 USBPWR is OFF (Default Setting) JP_USBSW1 S5 USBPWR is ON JP_USBSW1 SG-G151 USER MANUAL Page: 3-26...
Description: External USB 2.0 connector. Pin Assignment: ASSIGNMENT USB0_VCC5 USB0_P1_DN USB0_P2_DP USB0_GND USB1_VCC5 USB1_P1_DN USB1_P2_DP USB 2.0 USB1_GND 3.6.2 Power Button Connector Location: Power Button Description: Power Button ASSIGNMENT Power BTN Power LED + Power Button SG-G151 USER MANUAL Page: 3-27...
Chapter 4 Software Utilities Introduction Enclosed with SG-G151 Series package is our driver utilities contained in a DVD-ROM disk. Refer to the following table for driver locations: Filename (Assume that Purpose DVD- ROM drive is D :) D: \Driver\Platform\1_Main ®...
Page 49
Note: Install the driver utilities immediately after the OS installation is completed. It is strongly recommended that you follow the WARNING: installation sequence below: (1) Chipset Driver (2) Graphics Driver (3) TXE Driver (4) Other Drivers SG-G151 USER MANUAL Page: 4-3...
10 series, and it should be installed immediately after the OS installation is finished. Please follow the steps below: Connect the USB DVD-ROM device to SG-G151 and insert the driver disk. Enter the Main Chip folder where the Chipset driver is located.
Installation Instructions for Windows 10 To install the utility, simply follow the following steps: Connect the USB DVD-ROM device to SG-G151 and insert the driver disk. Enter the Hotfix folder where the driver is located.
Chapter 4 Software Utilities 4.2.3 Installing Graphics Driver Utility The GRAPHICS interface embedded in SG-G151 can support a wide range of display types. You can have dual displays via LVDS interfaces and make the system work simultaneously. To install the Graphics driver utility, follow the steps below: Connect the USB DVD-ROM device to SG-G151 and insert the driver disk.
Windows 10 series. To install the Sound Driver, follow the steps below: Connect the USB DVD-ROM device to SG-G151 and insert the driver disk. Open the Sound folder where the driver is located. Select Win10 2016 (64Bit) or Win10 2019 (64-Bit) for your OS platform.
Enhanced with LAN function, SG-G151 supports various network adapters. To install the LAN Driver, follow the steps below: Connect the USB DVD-ROM device to SG-G151 and insert the driver disk. Enter the LAN Chip folder where the driver is located.
4.2.6 Installing Intel Serial I/O Driver Utility To install the Serial I/O Driver, follow the steps below: Connect the USB DVD-ROM device to SG-G151 and insert the driver disk. Open the Serial IO folder where the driver is located. Select Win10 2016 (64Bit) or Win10 2019 (64-Bit) for your OS platform.
Windows 10, detects the system's capabilities and installs the relevant drivers and applications. Installation Instructions for Windows 10 Connect the USB DVD-ROM device to SG-G151 and insert the driver disk. Open the TXE folder where the driver is located.
The BIOS Setup Utilities consist of the following menu items: Accessing Setup Utilities • Main Menu • Advanced Menu • Chipset Menu • Security Menu • Boot Menu • Save & Exit Menu • SG-G151 USER MANUAL Page: 5-1...
Chapter 5 BIOS Setup Introduction The SG-G151 System uses an AMI (American Megatrends Incorporated) Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the built-in BIOS setup program, Power-On Self-Test (POST), PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
Page 59
After the system is powered on, users can access the BIOS setup menu by pressing <Del> or <Esc> immediately while the POST message is running before the operating system is loading. All the menu settings are described in details in this chapter. SG-G151 USER MANUAL Page: 5-3...
Self-Test (POST) routines and the POST message will be displayed: Figure 5-2. POST Screen with AMI Logo Press <Del> or <Esc> to access the Setup Utility program and the Main menu of the Aptio Setup Utility will appear on the screen as below: SG-G151 USER MANUAL Page: 5-4...
Page 61
US English. You may use <↑> or <↓> key to select among the items and press <Enter> to confirm and enter the sub-menu. The following table provides the list of the navigation keys that you can use while operating the BIOS setup menu. SG-G151 USER MANUAL Page: 5-5...
Page 62
<F2> Load the previous configuration values. <F3> Load the default configuration values. <F4> Save the current values and exit the BIOS setup menu. <Esc> Close the sub-menu. Trigger the confirmation to exit BIOS setup menu. SG-G151 USER MANUAL Page: 5-6...
Displays the date of current BIOS version. Time Access Level No changeable options Displays the current access level. BXT SOC No changeable options Displays the SOC stepping. MRC Version No changeable options Displays the MRC version. SG-G151 USER MANUAL Page: 5-7...
Page 64
The “Day” is automatically changed. Sets the system time. The format is [Hour: Minute: Second]. Users can directly enter System Time Hour, minute, second values or use <+> or <-> arrow keys to increase/decrease it. SG-G151 USER MANUAL Page: 5-8...
F81964 Watchdog Sub-Menu Watchdog timer parameters. S5 RTC Wake Settings Sub-Menu RTC wake parameters. CPU Configuration Sub-Menu CPU configuration parameters. F81964 Super IO Sub-Menu System Super IO chip parameters Configuration USB Configuration Sub-Menu USB configuration parameters. SG-G151 USER MANUAL Page: 5-9...
- Disabled Hibernate (OS/S4 Sleep State). This Enable Hibernation (S4) Enabled (default) option may be not effective with some - Disabled Enables or Disables System ability to Enable Sleep (S3) Enabled (default) Sleep (OS/S3 Sleep State). SG-G151 USER MANUAL Page: 5-10...
Displays the voltage level of VCC12V No changeable options VCC12V in supply. Displays the voltage level of VCC3V VCC3V No changeable options in supply. Displays the voltage level of VSB3V VSB3V No changeable options in supply. SG-G151 USER MANUAL Page: 5-12...
• Fixed Time: The system will wake - Disabled (default) Wake system from S5 - Fixed Time on the time (hr::min::sec) specified. - Dynamic Time • Dynamic Time: The system will wake on the current time + increased minute(s). SG-G151 USER MANUAL Page: 5-14...
(Numeric) from 0 to 23 power-on event. Sets a minute for a scheduled Wake up minute (Numeric)from 0 to 59 power-on event. Sets a second for a scheduled Wake up second (Numeric)from 0 to 59 power-on event. SG-G151 USER MANUAL Page: 5-15...
S5 RTC Wake Setting Screen (Dynamic Time) BIOS Setting Options Description/Purpose Sets a period of time (in minutes) to Wake up minute increase (Numeric) from 1 to 5 wake up the system after it enters S5 state. SG-G151 USER MANUAL Page: 5-16...
CPU Power Management Sub-Menu CPU power management options. When enabled, a VMM can utilize Intel Virtualization - Disabled the additional hardware capabilities Technology Enabled (default) provided by Vanderpool Technology. Disabled (default) VT-d Enables/Disables CPU VT-d. - Enabled SG-G151 USER MANUAL Page: 5-17...
Menu Path Advanced > CPU Configuration > CPU Power Management Configuration CPU Power Management Configuration Screen BIOS Setting Options Description/Purpose Enables/Disables Intel Speed Step - Disabled EIST feature for dynamic scaling processor Enabled (default) frequency. SG-G151 USER MANUAL Page: 5-19...
Advanced > F81964 Super IO Configuration F81964 Super IO Configuration Screen BIOS Setting Options Description/Purpose Displays the super I/O chip Super IO Chip (F81964) No changeable options model. Serial Port Configuration Sub-Menu The serial port parameters. SG-G151 USER MANUAL Page: 5-20...
Page 77
Allows user to change - IO=2F8h; IRQ=3 Device's Resource settings. - IO=3F8h; IRQ=3,4,5,7,9,10,11,12; Change Settings New settings will be reflected - IO=2F8h; IRQ=3,4,5,7,9,10,11,12; on This Setup Page after - IO=3E8h; IRQ=3,4,5,7,9,10,11,12; System restarts. - IO=2E8h; IRQ=3,4,5,7,9,10,11,12; SG-G151 USER MANUAL Page: 5-21...
- Floppy to their media format. Optical drives MASS STORAGE - Forced FDD are emulated as 'CD-ROM', drives with DEVICES: [drive(s)] - Hard Disk no media will be emulated according to - CD-ROM a drive type. SG-G151 USER MANUAL Page: 5-22...
This menu allows users to configure advanced Chipset settings such as North Bridge and South Bridge configuration parameters.. Chipset Screen BIOS Setting Options Description/Purpose North Bridge Sub-Menu North Bridge Parameters. South Bridge Sub-Menu South Bridge Parameters. SG-G151 USER MANUAL Page: 5-23...
"8192 MB( LPDDR3)". Memory Speed No changeable options Displays memory speed. Displays the current amount and type of Memory Slot0 No changeable options memory on each memory slot, e.g. "8192 MB (LPDDR3)". SG-G151 USER MANUAL Page: 5-24...
Chipset SATA - Enable SATA Controller. Displays SATA drive branding SATA Port 0 No changeable options information if the device exists on port 0. - Disabled Port 0 Enables or Disables SATA Port 0 Enabled (default) SG-G151 USER MANUAL Page: 5-30...
(WOL). - Disabled Win 8/8.1/10 don't support WOL from Wake On Lan Enabled hybrid shutdown state (S4). If user (default) needs WOL from classic shutdown state (S5), please turn off 'fast startup' feature in OS. SG-G151 USER MANUAL Page: 5-31...
Specifies the administrator password. Password alphanumeric characters. Password can be 3-20 User Password Specifies the user password. alphanumeric characters. Enter sub-menu with option to enabled HDD Security Sub-Menu password protected HDD/SSD Configuration (if supported by SATA device). SG-G151 USER MANUAL Page: 5-32...
Page 89
Security menu and press <Enter>, and the password dialog entry box appears. 2. Select the configured Administrator Password or User Password that you want to delete. Leave the dialog box blank and press <Enter>. 3. Press <Enter> again when the password confirmation box appears. SG-G151 USER MANUAL Page: 5-33...
• Specifies the power-on state of the NumLock State - Off NumLock Key. When quite boot is enabled, it displays -Disabled (default) AMI or OEM logo (if implemented) Quiet Boot -Enabled instead of POST messages during the boot. SG-G151 USER MANUAL Page: 5-34...
Page 91
Options Description/Purpose -Disabled (default) Fast Boot Enabled or Disabled Fast Boot Options. -Enabled -Windows (default) OS Selection Selects the target OS. -Intel Linux Boot Option - [Drive(s)] Sets the system boot order. #1~#n - Disabled SG-G151 USER MANUAL Page: 5-35...
Discard Changes and Reset to discard any changes you have made and restore the factory BIOS defaults. Load User Defaults You may simply press F3 at any time to load the Optimized Values which resets all BIOS settings to the factory defaults. Save & Exit Screen SG-G151 USER MANUAL Page: 5-36...
Page 93
Save the changes done so far as User No changeable options Defaults Defaults. Restore User Restore the User Defaults to all the setup No changeable options Defaults options. Boot Override - [Drive(s)] Forces to boot from selected [drive(s)]. SG-G151 USER MANUAL Page: 5-37...
System Exploded Diagram Component Name P/N No. Q’ty Heatsink O Ring Circle (ψ260.15x3mm) 30-013-06200426 TP PCBA Round Washer Head Screw 22-242-30005311 M3x0.5Px5mm Fillister Head Screw #2 / M3x0.5Px7mm 22-270-30007011 Waterproof Screw O Ring (OD=φ 23-680-36156507 6.5mm,ID=φ3.6mmx1.5T) SG-G151 USER MANUAL Page: A-2...
27-008-41505081 HDD Square Ring (82.05x22.29x2.4mm) 30-013-06100426 HDD Tray (w/Paint) (Silver) 20-054-03061426 SATA HDD SG-G151 Heatsink For PWR 21-002-12312002 (23.1x11.7x15.2mm) SG-G151 Heatsink For Super I/O 21-002-12726001 (26.7x26.2x17.8mm) SG-G151 Heatsink For LAN 21-002-12312001 (23.1x11.7x18mm) Heatsink CPU (37.2x24x14.73mm) 21-002-13724001 SG-G151 USER MANUAL Page: A-4...
Page 98
Appendix A System Diagrams Component Name P/N No. Q’ty Main PCBA Fillister Head Screw #2 / M3x0.5Px5mm 22-272-30049015 Flat Head Screw #2 / M3x0.5Px4mm 22-215-30004311 Fillister Head Screw #2 / M3x0.5Px6mm 82-275-30006018 Theraml - PAD Waterproof Film 34-034-06201426 SG-G151 USER MANUAL Page: A-5...
Round Head With Spring Washer Screw 22-232-40008211 M4x0.7Px8mm Fillister Head Screw #2 / M3x0.5Px7mm 22-270-30007011 Flat Head Screw #2 /ψ6/M4x0.7Px6mm 22-212-40006011 Note: The tube import adapter is designed for Stand Installation with 48 mm tubes. SG-G151 USER MANUAL Page: A-6...
This appendix will give you a brief introduction of the allocation maps for the system resources. The following topics are included: • BE-0986 Block Diagram • Interrupt Map • I/O Map • Memory Map • Configuring WatchDog Timer • Flash BIOS Update SG-G151 USER MANUAL Page: B-1...
USB2.0 RS232 F81964 RS-232 LOW PIN COUNT COM3/4 support 5V/12V (Super IO) SATA x1 COM 2 SATA3.0 RS232/422/485 BOARD ID SATA3.0 mSATA x1 FOR BIOS VERSION DETECT Mini PCI-E Slot (BE-0986RC default : 0001) USB2.0 SG-G151 USER MANUAL Page: B-2...
IRQ 77 Microsoft ACPI-Compliant System IRQ 78 Microsoft ACPI-Compliant System IRQ 79 Microsoft ACPI-Compliant System IRQ 80 Microsoft ACPI-Compliant System IRQ 81 Microsoft ACPI-Compliant System IRQ 82 Microsoft ACPI-Compliant System IRQ 83 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-3...
Page 104
IRQ 112 Microsoft ACPI-Compliant System IRQ 113 Microsoft ACPI-Compliant System IRQ 114 Microsoft ACPI-Compliant System IRQ 115 Microsoft ACPI-Compliant System IRQ 116 Microsoft ACPI-Compliant System IRQ 117 Microsoft ACPI-Compliant System IRQ 118 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-4...
Page 105
IRQ 147 Microsoft ACPI-Compliant System IRQ 148 Microsoft ACPI-Compliant System IRQ 149 Microsoft ACPI-Compliant System IRQ 150 Microsoft ACPI-Compliant System IRQ 151 Microsoft ACPI-Compliant System IRQ 152 Microsoft ACPI-Compliant System IRQ 153 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-5...
Page 106
IRQ 182 Microsoft ACPI-Compliant System IRQ 183 Microsoft ACPI-Compliant System IRQ 184 Microsoft ACPI-Compliant System IRQ 185 Microsoft ACPI-Compliant System IRQ 186 Microsoft ACPI-Compliant System IRQ 187 Microsoft ACPI-Compliant System IRQ 188 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-6...
Page 107
IRQ 268 Microsoft ACPI-Compliant System IRQ 269 Microsoft ACPI-Compliant System IRQ 270 Microsoft ACPI-Compliant System IRQ 271 Microsoft ACPI-Compliant System IRQ 272 Microsoft ACPI-Compliant System IRQ 273 Microsoft ACPI-Compliant System IRQ 274 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-7...
Page 108
IRQ 303 Microsoft ACPI-Compliant System IRQ 304 Microsoft ACPI-Compliant System IRQ 305 Microsoft ACPI-Compliant System IRQ 306 Microsoft ACPI-Compliant System IRQ 307 Microsoft ACPI-Compliant System IRQ 308 Microsoft ACPI-Compliant System IRQ 309 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-8...
Page 109
IRQ 338 Microsoft ACPI-Compliant System IRQ 339 Microsoft ACPI-Compliant System IRQ 340 Microsoft ACPI-Compliant System IRQ 341 Microsoft ACPI-Compliant System IRQ 342 Microsoft ACPI-Compliant System IRQ 343 Microsoft ACPI-Compliant System IRQ 344 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-9...
Page 110
IRQ 373 Microsoft ACPI-Compliant System IRQ 374 Microsoft ACPI-Compliant System IRQ 375 Microsoft ACPI-Compliant System IRQ 376 Microsoft ACPI-Compliant System IRQ 377 Microsoft ACPI-Compliant System IRQ 378 Microsoft ACPI-Compliant System IRQ 379 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-10...
Page 111
IRQ 408 Microsoft ACPI-Compliant System IRQ 409 Microsoft ACPI-Compliant System IRQ 410 Microsoft ACPI-Compliant System IRQ 411 Microsoft ACPI-Compliant System IRQ 412 Microsoft ACPI-Compliant System IRQ 413 Microsoft ACPI-Compliant System IRQ 414 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-11...
Page 112
IRQ 443 Microsoft ACPI-Compliant System IRQ 444 Microsoft ACPI-Compliant System IRQ 445 Microsoft ACPI-Compliant System IRQ 446 Microsoft ACPI-Compliant System IRQ 447 Microsoft ACPI-Compliant System IRQ 448 Microsoft ACPI-Compliant System IRQ 449 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-12...
Page 113
IRQ 478 Microsoft ACPI-Compliant System IRQ 479 Microsoft ACPI-Compliant System IRQ 480 Microsoft ACPI-Compliant System IRQ 481 Microsoft ACPI-Compliant System IRQ 482 Microsoft ACPI-Compliant System IRQ 483 Microsoft ACPI-Compliant System IRQ 484 Microsoft ACPI-Compliant System SG-G151 USER MANUAL Page: B-13...
Page 115
IRQ 4294967293 Express Root Port - 5AD9 Intel(R) Celeron(R)/Pentium(R) Processor PCI IRQ 4294967294 Express Root Port - 5AD8 Note: These resource information were gathered using Windows 10 (the IRQ could be assigned differently depending on OS) SG-G151 USER MANUAL Page: B-15...
Page 117
Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 0x0000E000-0x0000EFFF 5AD8 Intel(R) HD Graphics 0x0000F000-0x0000F03F Intel(R) Celeron(R)/Pentium(R) 0x0000F040-0x0000F05F Processor SMBUS - 5AD4 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F090-0x0000F097 Standard SATA AHCI Controller SG-G151 USER MANUAL Page: B-17...
To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. SG-G151 USER MANUAL Page: B-20...
Page 121
;---------------------------------Enable Watch dog feature ------------------------------ ; ---------------- Set timeout interval as 30seconds and start counting -------------- ;------------------------------- Enable Watch PME-------------------------------------------- ;-------------------------- Set second as counting unit -------------------------------------- ;-------------------------- Start the watchdog timer -------------------------------------- ;---------------------------------Exit the extended function mode ------------------------- SG-G151 USER MANUAL Page: B-21...
(2) Turn on the computer and press <ESC> or <DEL> key during boot to enter BIOS Setup. (3) Select [Boot] menu and set USB bootable device as the 1 boot device. (4) Press <F4> key to save configuration and exit the BIOS setup menu. SG-G151 USER MANUAL Page: B-22...
Page 123
BIOS ROM may be crashed and the system will be unable to boot up next time. After the BIOS update procedure is completed, the following messages will be shown: SG-G151 USER MANUAL Page: B-23...
Page 124
5. Restart the system and boot up with the new BIOS configurations. 6. The BIOS Update is completed after the system is restarted. 7. Reboot the system and verify if the BIOS version shown on the initialization screen has been updated. SG-G151 USER MANUAL Page: B-24...