High performance taping heads 2 and 3 inch (50 pages)
Summary of Contents for 3M 3M-Matic 7000a Pro
Page 1
Instructions and Parts List 3M-Matic ™ 7000a-7000a3 Pro Type 22100 Adjustable Case Sealer with AccuGlide 3 Taping Heads ™ Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 2
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page ii...
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic ™ /AccuGlide ™ /Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® Tapes. Included with each machine is an Instructions and Parts List Manual.
Page 4
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page iv...
Page 5
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic ™ /AccuGlide ™ /Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® tapes. If any problems occur when operating this equipment and you desire a service call or phone consultation, call, write, or fax the appropriate number listed below.
Page 6
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page vi...
Page 8
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page viii...
Page 9
Column Repositioning ........26 – 27 NA - ENG 3M-Matic ™...
Page 10
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page x...
Page 11
Drawings and Parts Lists ......43 – End of Manual Taping Head Information ™ Manual 2: AccuGlide 3 Taping Heads — 2 Inch or 3 Inch (See Manual 2 or 3 for Table of Contents) NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page xi...
Page 12
AccuGlide ..Trademark of 3M St. Paul, MN 55144-1000 Scotch ..Trademark of 3M St. Paul, MN 55144-1000 Drw... . Drawing Ex.
1. Introduction Manufacturing Speci cations / Description / Intended Use The 3M-Matic ™ 7000a-7000a3 Pro Adjustable Case Sealer with AccuGlide ™ Taping Heads is designed to apply a “C” clip of Scotch ® pressure-sensitive lm box sealing tape to the top and bottom center seam of regular slotted containers.
2. General Information 2.1 Data Identifying Manufacturer and Machine For Commercial Use Only Data for Technical Assistance and Service Agent/Distributor or Local After Sale Service: NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 3...
Page 16
3M. A part will be presumed to have become defective after its warranty period unless the part is received or 3M is noti ed of the problem no later than ve (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M at its option, will replace the equipment or refund the purchase price.
Indicates a potentially hazardous situation, which, if not Warning avoided, could result in death or serious injury and/or property damage. NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 5...
Never put your hands inside any part the machine is running. of the machine while it is working. Serious injury may occur (Figure 3-4). NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 6...
Page 19
- Keep hands, hair, loose clothing, and jewelry away from box compression rollers and all moving parts. - Always feed boxes into the machine Figure 3-8 by pushing only from the end of box. NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 7...
- Allow only properly trained and qualifi ed - The operator must pay attention personnel to operate and service this to the blades during the tape equipment. replacement. NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 8...
Page 21
Extraordinary mechanical maintenance protections disabled Extraordinary electrical maintenance Stopped by pressing Adjusting box size the EMERGENCY STOP Tape replacement button Blade replacement Electric power Drive belt replacement disconnected Ordinary maintenance NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 9...
Stop Handle Switch Upper Machine Head Assembly Adjustable Side Guides Lower Tape Roll Mount Power (not shown) Switch Assembly Figure 3-9 7000a-7000a3 Pro Case Sealer Components (Left Front View) NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 10...
The machine is equipped with two 1/4 HP gearmotors and comes with an 2.4m [8 foot] standard neoprene covered power cord and a grounded plug. Contact your 3M Rep- resentative for power requirements not listed above. Contact your 3M Representative for power requirements not listed above.
“Special Set-Up Procedure” section of this manual. Refer to illustration/chart for box height range possibilities by adjusting machine upper frame and/or outer column positioning. NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017...
Page 27
Note: interference. Special modi cations may be available for carton sizes. Contact your 3M Representative for information. However, if the box length (in direction of seal) to box height ratio is .6 or less, then several boxes should be test run to assure proper machine performance.
- Do not stack anything over the machine. - It is possible to stack a maximum Figure 5-4 of 2 machines (if they are in their original packing). NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 17...
(sea freight package only) - Polyethylene protective material For the disposal of the above materials, please follow the environmental directives or the law in your country. . Figure 6-5 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 18...
4 - Repeat the operation for all legs. (It is not necessary to x or anchor the machine to the oor). 5 - For Outer Column Repositioning- See Special Set-up Procedure (Section 11). Figure 7-3 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 19...
Connect the power cord supplied with the end of the lower frame machine to a wall socket using a plug which (as shown in Figure 7-9). complies with the safety regulations of your country. NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 21...
8.3.2 Emergency Stop The LATCHING EMERGENCY STOP BUTTON is located on the top center of the machine (Figure 8-3). Belt Direction Figure 8-3 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 22...
Allow only properly trained and quali ed • Have wire size 1.5mm dia. [AWG 16] personnel to operate and service this • Have a max. length 30.5m [100 ft] equipment. • Be properly grounded. NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 24...
6. Refer to Manual 2, “Adjustments—Changing Tape Leg Length”, for taping head setup. 7. Replace taping heads in the reverse order of disassembly. Taping Heads - Important! Turn o Electric Power NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017...
Page 38
Note: You may also need to loosen the two set screws in the nut plate bracket (located above bottom two column screws). (continued on next page) Note: Loosen but do not Remove Column Screws Figure 11-7 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 26...
Page 39
An additional adjustment can be made to reach Maximum Height. This additional height adjustment can be made by moving the Upper Assembly Crossbar up to the top holes - (Figure 11-8). Figure 11-8 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 27...
1. Taping units blade guard the machine by turning OFF (O) switch on the main and disconnect 2. Latching emergency stop button electric power (Figure 12-3). 3. STOP (OFF) (O) main switch NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 28...
Page 41
Replace friction rings Drive belt tension too low Adjust belt tension Electrical disconnect Check power and electrical plug Motor not turning Evaluate problem and correct (continued on next page) NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 29...
The blade is not cutting tape properly Refer to tape cutting problems The tape is threaded incorrect Rethread tape Applying mechanism spring Move spring hook to next has too little tension tighter hole NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 30...
13. Maintenance and Repairs (continued) 13.8 Box Drive Belt Replacement Note – 3M recommends the replacement of drive belts in pairs, especially if belts are unevenly worn. Lower Drive Belts (Figure 13-1) 1. Remove and retain center plate (A) and four (4) screws.
Box Drive Belt 3.5kg (7lbs) Pull Force with 25mm (1 inch) at Mid span Infeed End Discharge End Figure 13-4 Box Drive Belt Tension Adjustment NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 33...
Page 46
Machine Frame) Figure 13-5 Lower Drive Front Pan Hd Screw Cover Drive Belts Lock Wrench Hex Hd Infeed End Tension Screw Figure 13-6 Upper Drive NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 34...
Use a re extinguisher that is rated for electrical res - (Figure 14-2). Figure 14-2 15. Additional Information 15.1 Statement of Conformity 15.2 Emission of Hazardous Substances Nothing to report NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 37...
Page 53
• Figure Number In the event that any labels are damaged • Position or destroyed, they must be replaced to • 3M Part Number (11 Digits) ensure operator safety. A label kit, • Description part number 78-8137-7538-0 , is available •...
Page 54
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 40...
Page 55
Options and Accessories Case Sealer, Type 11500 21500 For additional information on the options and Frame Assemblies accessories listed below - contact your 3M Representative. To Order Parts: Part Number Option / Accessory 1. Refer to rst illustration, Frame Assemblies, for the...
Page 56
NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 42...
Page 57
7000a-7000a3 Pro Figure 15950 Figure 15967 Figure 15947 Figure 15843 Figure 15946 Figure 15842 Figure 15845 Figure 15948 (not shown) Figure 15950 Figure 15978 (not shown) Frame Assemblies NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 43...
Page 58
7000a-7000a3 Pro Figure 15842 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 44...
Page 62
3” Taping Head only This page needs changed and the parts list corrected on the next page Note: See Parts List for Accuglide 2” and 3” information Figure 15967 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 48...
Page 68
7000a-7000a3 Pro 26 27 31 30 78-8137-6366-7 Cover Assembly - Drive Belt Right 78-8137-6367-5 Cover Assembly - Drive Belt Left 52 51 Figure 15947 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 54...
Page 70
7000a-7000a3 Pro Items 1-8 & 12,13 = 78-8137-7950-7 Pulley Assy Figure 15948 NA - ENG 3M-Matic ™ 7000a-7000a3 Pro March 2017 Page 56...
Page 71
7000a-7000a3 Pro Figure 15948 Figure 15948 Ref. No. 3M Part No. Description 15948-1 78-8060-8416-2 Nut - M20X1 Special 15948-2 78-8076-5105-0 Driving Pulley 15948-3 78-8052-6713-1 Ring - Polyurethane 15948-4 78-8070-1529-8 Support - Shaft 15948-5 78-8070-1530-6 Radial Ball Bearing - 6205-2RS 15948-6...
Page 72
7000a-7000a3 Pro 7000r-7000r3 HS Pro Figure 16054 North American - ENG 3M-Matic 7000r-7000r3 HS Pro - Type 11800 ™ Date Released: Page 86 10-19-20 44-0009-2152-6 / ECO# 0078045...
Instructions and Parts List 3M-Matic Accuglide ™ ™ Type 10800 Upper and Lower High Speed Taping Heads 2 Inch Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 78
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page ii...
Page 79
Minimum billing on parts orders will be $50.00. Replacement part prices available on request. There will be a 15% restocking fee per invoice on returned parts. Note: Outside the U.S. contact the local 3M subsidiary for parts ordering information NA - ENG 3M-Matic ™...
Page 80
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page iv...
Page 81
Replacement Parts and Service Information (continued) To Our Customers: ™ ™ ® This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set up and tested in the factory with Scotch ® tapes. If any problems occur when operating this equipment and you desire a service call or phone consultation, call, write, or fax the appropriate number listed below.
Page 82
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page vi...
Page 83
Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head...
3M to its factory or other authorized service station designated by 3M. If 3M is unable to repair or replace the part within a reasonable time after receipt thereof, 3M, at its option, will replace the equipment or refund the purchase price.
These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™...
Page 86
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 2...
(ELV), a glossary with a de nition of symbols, plus a parts list of the 3M-Matic™ Accugllide 3 (2 inch) 3M Industrial Adhesives and Tapes Division 3M Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA) Edition April 2017/ Copyright 3M 2017.
The blades are extremely sharp. system is running (Important Safeguards continued on next page) NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 4...
Page 89
See "Replacement Parts Illustrations and Parts Lists" for label part numbers. Upper Taping Head Label 78-8137-3317-3 Lower Taping Head Label 78-8137-3316-5 78-8070-1335-0 Figure 1-1 Replacement Labels/3M Part Numbers NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head...
5. Box Size Capacities: For use with center seam regular slotted containers. When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual speci cations for box weight and size capacities. 6. Operating Rate: Conveyor speeds up to 0.5 m/s [100 feet per minute].
* This dimension can be reduced to 90mm [3-1/2 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 7...
Taping Head is supplied with a bu ng the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.
Spring One-Way Tension Roller Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head (Left Side View) NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 9...
2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 10...
Page 95
Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 11...
Silicone. Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 12...
Insert a 4mm hex key wrench into this socket after removing one screw to hold the shaft for removal of the second screw. See Figure 4-2. NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 13...
- Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 14...
- Never attempt to work on the taping Figure 5-5 One-Way Tension Roller head or load tape while the box drive system is running (Adjustments continued on next page.) NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 15...
- Never attempt to work on the taping cuto blades under orange blade guards. head or load tape while the box drive The blades are extremely sharp. system is running NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 16...
Make sure one-way bearing is contacting the taping head frame below the surface of the tension roller. If not, press bearing further into roller or replace roller. NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 17...
Page 102
Reposition tape drum Tape not centered on box seam Centering guides not centered Adjust centering guides Box aps not of equal length Check box speci cations NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 18...
Roller – Buffi ng 78-8113-7030-9 Spring – Torsion Replacement Parts and Service Refer to the fi rst page of this instruction manual “Replacement Parts and Service Information". NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 19...
Page 104
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 20...
Page 105
Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to con rm item availability. NA - ENG 3M-Matic ™...
Page 106
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 22...
Page 107
Tape Head Figures AccuGlide ™ 3 - 2 inch Figure 10401 Figure 10925 Figure 10924 Figure 10923 Figure 10922 Figure 10919 Figure 10921 Figure 10920 NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 23...
Page 108
™ AccuGlide 3 - 2" Figure 10925 – Upper Head NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 24...
Page 122
™ AccuGlide 3 - 2" Figure 10920 – Lower Head NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 38...
Page 123
™ AccuGlide 3 - 2" Figure 10920– Lower Head Ref. No. 3M Part No. Description 10920-1 78-8137-3300-9 Buffi ng Arm – Sub Assembly 10920-2 78-8137-3301-7 Buffi ng Arm – Sub Assembly 10920-3 78-8052-6575-4 Shaft – Roller 10920-4 78-8137-1398-5 Roller - Buffi ng Assembly...
Page 124
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 40...
Page 125
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 41...
Page 126
NA - ENG 3M-Matic ™ Accuglide 3 - 2 Inch Taping Head April 2017 Page 42...
Page 127
It is recommended you immediately order the spare parts listed in the “Spare Parts/Service Information” section. These parts are expected to wear through normal use, and should be kept on hand to minimize production delays. NA - ENG ™ 3M-Matic 7Accuglide 3 - 3 Inch Taping Head April 2017 Page i...
Page 128
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page ii...
Page 129
Minimum billing on parts orders will be $50.00. Replacement part prices available on request. www.combi.com There will be a 15% restocking fee per invoice on returned parts. Note: Outside the U.S. contact the local 3M subsidiary for parts ordering information 45>D9 31D9?> <1D5 ?B ?==5B391< %C5 ><I...
Page 130
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page iv...
Page 131
"5@<135=5>D 1BDC 1>4 #5BF935 >6?B=1D9?> (continued) $? EB ECD?=5BC ™ ™ ® This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set up and tested in the factory with Scotch ® tapes. Included with each machine is an Instructions and Parts List Manual.
Page 132
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page vi...
Page 133
Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head...
Page 134
3M to its factory or other authorized service station designated by 3M. If 3M is unable to repair or replace the part within a reasonable time after receipt thereof, 3M, at its option, will replace the equipment or refund the purchase price.
Page 135
These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™...
Page 136
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 2...
Page 137
Accugllide 3 (3 inch) 3M Industrial Adhesives and Tapes Division 3M Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA) Edition April 2017/ Copyright 3M 2017. All rights reserved The manufacturer reserves the right to change the product at any time without notice.
Page 138
The blades are extremely sharp. system is running (Important Safeguards continued on next page) NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 4...
Page 139
See "Replacement Parts Illustrations and Parts Lists" for label part numbers. %@@5B $1@9>7 514 125< ?G5B $1@9>7 514 125< 97EB5
"5@<135=5>D 125<C 1BD E=25BC NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 5...
Page 140
For use with center seam regular slotted containers. 9>9=E= 1H9=E= Length – 150mm [6 inches] Unlimited Height – 120mm [4-3/4 inches] (most “3M-Matic” Case Sealers) Limited by 90mm [3-1/2 inches] (with optional 2 inch leg length) Case Sealer Width – 150mm [6 inches]...
Page 141
* This dimension can be reduced to 90mm [3-1/2 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 7...
Page 142
Taping Head is supplied with a bu ng the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. >CD1<<1D9?> E945<9>5C 4.
Page 143
5381>9C= #@B9>7 >5
'1I $5>C9?> "?<<5B $1@5 485C9F5 #945 $1@5 #E@@<I "?<< $1@5 BE= 97EB5 $1@9>7 514 ?=@?>5>DC$8B5149>7 917B1=
?G5B 514 56D #945 &95G NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 9...
Page 144
2. Lower taping head is loaded and 97EB5 $1@5 ?149>7$8B5149>7 threaded in same manner as upper head. NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 10...
Page 145
Excess tape can be cut with a scissors at applying roller. 97EB5 $1@5 ?149>7$8B5149>7 97EB5 $1@5 ?149>7$8B5149>7 NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 11...
Page 146
Silicone. Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 12...
Page 147
Insert a 4mm hex key wrench into this socket after removing one screw to hold the shaft for removal of the second screw. See 97EB5 NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 13...
Page 148
- Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 14...
Page 149
- Never attempt to work on the taping 97EB5 >5
'1I $5>C9?> "?<<5B head or load tape while the box drive system is running (Adjustments continued on next page.) NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 15...
Page 150
- Never attempt to work on the taping cuto blades under orange blade guards. head or load tape while the box drive The blades are extremely sharp. system is running NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 16...
Page 151
Make sure one-way bearing is contacting the taping head frame below the surface of the tension roller. If not, press bearing further into roller or replace roller. NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 17...
Page 152
Reposition tape drum Tape not centered on box seam Centering guides not centered Adjust centering guides Box aps not of equal length Check box speci cations NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 18...
Page 153
Roller – Buffi ng 78-8113-7030-9 Spring – Torsion "5@<135=5>D 1BDC 1>4 #5BF935 Refer to the rst page of this instruction manual "5@<135=5>D 1BDC 1>4 #5BF935 >6?B=1D9?> NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 19...
Page 154
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 20...
Page 155
Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to con rm item availability. NA - ENG 3M-Matic ™...
Page 156
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 22...
Page 157
™ AccuGlide 3 - 3” $1@5 514 33E<945 9>38 97EB5 97EB5 %@@5B 97EB5 ?G5B 97EB5 97EB5 97EB5 %@@5B 97EB5 97EB5 ?G5B NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 23...
Page 158
™ AccuGlide 3 - 3” Figure 10932 – Upper Head NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 24...
Page 162
AccuGlide ™ 3 - 3” Figure 10926 – Upper Head NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 28...
Page 163
™ AccuGlide 3 - 3” Figure 10926 – Upper Head Ref. No. 3M Part No. Description 10926-1 78-8137-3300-9 Buffi ng Arm – Sub Assembly 10926-2 78-8137-3301-7 Buffi ng Arm – Sub Assembly 10926-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon...
Page 164
™ AccuGlide 3 - 3” Figure 10930 – Upper and Lower Heads NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 30...
Page 165
™ AccuGlide 3 - 3” Figure 10930 – Upper and Lower Heads Ref. No. 3M Part No. Description 10930-1 78-8137-3302-5 Link – R/H Assembly 10930-3 78-8137-3314-0 Shaft – Pivot, Buffi ng 10930-4 78-8017-9082-1 Bearing – Special 30 mm 10930-5 78-8017-9106-8 Screw –...
Page 166
™ AccuGlide 3 - 3” Figure 10928 – Upper and Lower Heads NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 32...
Page 172
AccuGlide ™ 3 - 3” Figure 10927 – Lower Head NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 38...
Page 173
™ AccuGlide 3 - 3” Figure 10927 – Lower Head Ref. No. 3M Part No. Description 10927-1 78-8137-3300-9 Buffi ng Arm – Sub Assembly 10927-2 78-8137-3301-7 Buffi ng Arm – Sub Assembly 10927-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon...
Page 174
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 40...
Page 175
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 41...
Page 176
NA - ENG 3M-Matic ™ Accuglide 3 - 3 Inch Taping Head April 2017 Page 42...