Table of Contents
Advertisement
z
0
(J1
(J1
<.O
OJ
' ......
_.. 18
•
•
I
HOW TO PERFORM SET-UP MENU
ADJUSTMENTS
(cont'd.)
WHITE BALANCE ADJUSTMENT
You can set (adjust) the white balance of the screen.
This function (WHITE BALANCE) is set in the <SET-UP MENU>
screen.
1 While pressing the
SELECT
I;.]
button, press
the VOLUME/ENTER
l1i:J
button.
The <SET-UP MENU> screen
appears.
2 Press the SELECT
Ell
button to select the
•ITT•
[WHITE BALANCE] item.
The selection
mark( ► )
moves to
the [WHITE BALANCE] item,
3 Press the VOLUME/
ENTER
r:tl:]1(Q]
buttons.
• The present color temperature
status is displayed to the right of
<WHITE BALANCE>: HIGH or
LOW,
• The present color temperature
status is the same as in the
[COLOR TEMP.] ~em on the
<FUNCTION SELECT> screen
available from the <MAIN MENU>
screen.
4 Press the SELECT
Ell
button to select
=•
the desired adjustment
item.
The selection
mark( ► )
moves to
the adjustment item.
<SET-UP MENU> screen
<SET-UP MENU> screen
<WHITE BALANCE> screen
<WHITE BALANCE> screen
5 Perform adjustment with the VOLUME/
ENTER i:tl]11J!)
buttons.
• You can set (adjust) WHITE BALANCE to HIGH or LOW.
Items
BLUE DRIVE
RED DRIVE
Contents
Adjusts the blue drive leveL
CD ,, ,
Decreases the blue drive leveL
c:!:J ...
Increases the blue drive level.
Adjusts the red drive leveL
[fil
... Decreases the red drive level.
c:J ...
Increases the red drive level.
GREEN CUT OFF Sets the green cutoff point.
CTI] ,, ,
Decreases the green cutoff
point.
c::tJ ...
Increases the green cutoff
point
BLUE CUT OFF
Sets the blue cutoff point
CJ . , ,
Decreases the blue cutoff point.
CJ ,, .
Increases the blue cutoff point
RED CUT OFF
Sets the red cutoff point
G:J ,,.
Decreases the red cutoff point
CJ , ..
Increases the red cutoff point.
• BLUE DRIVE
• adjusts the blue drive
• RED DRIVE
: adjusts the red drive
• GREEN CUT OFF : adjusts the green cutoff
• BLUE CUT OFF
: adjusts the blue cutoff
• RED CUT OFF
: adjusts the red cutoff
• There is a total range of 256 for each item. "MIN" is displayed for the
minimum level,
and
"MAX" for the maximum level. Each item's
factory-set value is listed as "000 (STANDARD)", and
the
available
range up(+) or down(-) varies (although there are always 256
values total, including "MIN", "ODO" and "MAX").
Therefore, the values for "MtW and "MAX" vary for each item.
•
•
■
SELECTING [ +-Sub menu] IN PROCEDURE 4
You can also adjust items in procedure 5 with only the
selected item displayed. Use this if the full menu screen
makes rt difficult to observe the monitor image.
G)Select the ( +-sub menu] Item in procedure 4.
Q)Pressthe VOLUME/
□
ENTER
CTlJ
button.
The <sub menu> screen appears.
(A single item is displayed at a
time.)
•
"", ,·~
.•:•
@Press the SELECT~ button to
select the desired Item.
©Perform adjustment with the
VOLUME/ENTER
CTtJtD!]
buttons.
<SUb menu> screen
■
RESETTING ITEMS TO THEIR FACTORY-SET (INITIAL)
VALUES
You can reset the <WHITE BALANCE> ~ems to their
factory-set (initial) values.
G)Select the (reset] Item
in
procedure 4.
Q)Press the VOLUME/ENTER CT2]
[;_;]
button.
The <reset> screen appears.
@Perform adjustment with the
,,_ ..
~.~s'';~:~·i
~:;
VOLUME/ENTER
ctl
button
or the MENU
t;;!
button.
<r8SEII> screen
VOLUME/ENTERIJI)
button ... Values are reset.
MENU button
1:1 ...
Reset is aborted
-
(values are unchanged).
* The screen from procedure 4 reappears.
6 After adjustment is complete, press the
MENU
IQ)
button twice to exit the menu
screen~•
( Notes: }
• The menu screen automatically disappears when no
operation is pertormed after about 30 seconds.
• When a prompt appears in the menu screen, it does not
disappear until the operation requested is performed.
• Items that cannot be set or adjusted in the current input
mode (INPUT SELECT) are not displayed.
•
RESETTING ALL MENU ITEMS TO
THEIR FACTORY-SET (INITIAL)
VALUES
You can
reset
all the hems In the
<MAIN
MENU> screen and
<SET~UP MENU> screen to their factory-set (initial) values.
This
function (all
reset) is set
in
the
<SET-UP
MENU>
screen.
1 While pressing the
SELECT
C3
button, press
the VOLUM,E/ENTER
0:0
button.
The <SET-UP MENU> screen
appears.
2 Press the SELECT
CJ
button to select the """
[& all reset] item.
The selection
mark( ► )
moves to
the [
&
all reset] item,
3 Press the VOLUME/
ENTER
G!J
button.
The <all reset> screen appears.
<SET-UP MENU> screen
<SET-UP MENU> screen
<all reset> screen
4 Perform adjustment with the VOLUME/
ENTER
G!J
button or the MENU
[J
button.
VOLUME/ENTER
Cl]
button ... All the ite~; are reset to
their factory-set (initial)
values.
MENU~button
... All-reset is aborted
(values are unchanged).
• The screen from procedure 2 (the <SET-UP MENU> screen)
reappears.
5 After adjustment is complete, press the
MENU
g
button to exit the menu screen.
( Notes: }
• All the menu items are reset. If there are items you do not
want to reset, cancel <all reset>.
• The menu screen automatically disappears when no
operation is performed after about 30 seconds.
• When a prompt appears in the menu screen, it does not
disappear until the operation requested is performed.
19
0
-I
<
N
0
0
0
(/)
C
Advertisement
Chapters
Table of Contents
