DT-V24L1D DT-V24L1 DT-V20L1D DT-V20L1 MULTI FORMAT LCD MONITOR The illustration of the monitor is of DT-V24L1D. INSTRUCTIONS Table of Contents Safety Precautions ... 2 IMPORTANT SAFEGUARDS ... 2 Maintenance ... 3 Installation ... 4 Using the monitor on the stand ... 4 Installing the monitor in the rack ...
U.S.A. only FCC NOTICE CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
European Union. national legislation. (Business users) If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take-back of the product. [Other Countries outside the European Union] If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.
Installation CAUTION • Do not rest your arm on the monitor or lean against the monitor. • Do not hold the LCD panel when installing the monitor. • Make sure to install the monitor securely to prevent the monitor from falling over, which causes damage to the monitor or injury. 7 Using the monitor on the stand You can place the monitor in the following two ways when using the monitor on the supplied stand.
Screw holes (See page 18 for the specifications of the screw holes.) 7 Installing the monitor in the rack Use a JVC’s RACK MOUNT ADAPTER (RK-C20L1; not supplied). CAUTION • Detach the stand first. • Ask your dealer to install.
☞ “Menu Operations” on page 7 SAFETY MARKER button/lamp Activates/deactivates the settings of “ASPECT SELECT,” “R-ASPECT SELECT,” “SAFETY AUDIO (DT-V24L1D and DT-V20L1D only). MARKER” and “R-SAFETY MARKER” in “AREA ☞ “Audio Channel Selection” on page 7 MARKER” (☞ 10 page).
Page 7
CRC error indication* ☞ “CRC ERROR” in “INFORMATION” on page 13 • A red square is displayed when an error occurs. * DT-V24L1D and DT-V20L1D only If you press INPUT SELECT button of the current input, the information below ( displayed in large letters for about three seconds.
• Select the signal type in “DVI INPUT SEL.” corresponding to the type of the input signal (☞ page 10). *Using the audio level meter (DT-V24L1D and DT-V20L1D only) You can check the conditions of the current EMBEDDED AUDIO signals in the audio level meter. The setting for the level meter is selected in “LEVEL METER SETTING”...
1920 1080 67.5 For DT-V20L1D and DT-V20L1: When No. 8, 9 or 11 signal is input, thin lines will become obscured because their signal resolution is higher than the screen resolution. Specification of DVI-D (HDCP) terminal Connect it to DVI-D output terminal on a personal computer.
Menu Configuration —MAIN MENU For the operation procedure, see page 7. Operation guide Shows the buttons for each operation. NOTE • The menu automatically disappears in about 30 seconds after the last menu operation. • Some items may not appear on the menu depending on the input or the input signal. These items are not available. Technical information Setting of “MARKER SELECT”...
Page 11
Item NO SYNC ACTION DELAY TIME SYNC INPUT SEL.* QUICK SWITCHING OVER LEVEL REFERENCE LEVEL DT-V24L1D and DT-V20L1D only Memorized for each input. Yellow Green To do Select the contents and displaying position of “sub menu.” Select the color system.
Menu Configuration —SET-UP MENU For the operation procedure, see page 7. Operation guide Shows the buttons for each operation. NOTE • The menu automatically disappears in about 30 seconds after the last menu operation. • Some items may not appear on the menu depending on the input or the input signal.
Page 13
• “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset. • After performing “all reset,” the monitor is turned off then turned on automatically. button to reverse the order. DT-V24L1D and DT-V20L1D only Memorized for each input. To do...
COMP./RGB Changes the input to “COMPO./ RGB.” DT-V24L1D and DT-V20L1D only Must be controlled with the TRIGGER system. Selects which functions in “AREA MARKER” are activated, “R-” items or non-“R-” items (☞ page 10). Displays the information shown when INPUT SELECT button of the current input is pressed (☞ “About the Status Display” on...
“ ** ” is monitor’s ID. Normally, set to “00.” Enter the appropriate data to “xx”. These commands are available for only DT-V24L1D and DT-V20L1D. Displays the information shown when INPUT SELECT button of the current input is pressed (☞ “About the Status Display” on page 7).
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solves the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action No power supply •...
AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder) Notice on transportation This monitor is precision equipment and needs dedicated packing material for transportation. Never use any packing material supplied from sources other than JVC or JVC-authorized dealers. Options (not supplied) RACK MOUNT ADAPTER (DT-V20L1D and DT-V20L1 only):...
51 (2 243 (9 <Rear view> VESA mounting holes (Size: M4, depth: 10 mm) The illustrations of the monitor are of DT-V24L1D. <Rear view> VESA mounting holes (Size: M4, depth: 10 mm) The illustrations of the monitor are of DT-V20L1D.