Table of Contents
Advertisement
AX-E78BK
AX-E79TN
Safety Precautions
. The design of this product contains special hardware
and many circuits and components
specially for safety purposes.
For continued protection, no changes should be made to the
original design unless authorized in writing by the manufacturer.
Replacement parts must
be identical
to those
used
in the
original
circuits.
Services
should
be performed
by
qualified personnel only.
). Alterations
of. the design or circuitry of the product should
not be made.
Any design
alterations of the product should not be made.
Any design alterations or additions will
void the manufacturer's warranty and will further relieve the manufacture of responsibility
for personal injury or property damage resulting therefrom.
. Many
electrical
and
mechanical parts
in the
products
have
special
safety-related
characteristics.
These characteristics are often not evident from visual inspection nor can
the protection afforded by them necessarily be obtained by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified
in the Parts List of Service Manual.
Electrical
components
having such features are identified by shading on the schematics and by ( A\) on the Parts
List in the Service Manual.
The use of a substitute repalcement which does not have the
same safety characteristics as the recommended
replacement parts shown in the Parts List of
Service Manual may create shock, fire, or other hazards.
. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and
the like to be separated from live parts, high temperature parts, moving parts and/or sharp
edges for the prevention of electric shock and fire hazard.
When
service is required, the
original lead routing and dress should be observed, and it should be confirmed that they
have been returned to normal, after re-assembling.
. Leakage currnet check (Electrical shock hazard testing)
- After re-assembling the product, always perform an isolation check on the exposed metal
parts of the product (antenna terminals, knobs, metal cabinet, screw heads, headphone jack,
contorl shafts, etc.) to be sure the product is safe to operate without danger of electrical
shock.
Do not use a line isolation transformer during this check.
@ Plug the AC line cord directly into the AC outlet.
Using a "Leakage Current Tester",
measure the leakage current from each exposed metal parts of the cabinet, particularly
any exposed
metal
part having a return path to the chassis, to a known
good earth
ground.
Any leakage current must not exceed 0.5mA AC (r.m.s.).
.
e@ Alternate check method
Plug the AC line cord directly into the AC outlet.
Use an AC voltmeter
having,
1,000
ohms per volt or more
sensitivity in the following
manner.
Connect a 1,500Q
10 W
resistor paralleled by a 0.15 uF AC-type capacitor between
an exposed metal part and a
known good earth ground.
Measure
the
AC
voltage
across
the
resistor
(Having 1000
with the AC voltmeter.
ohms/volts,
Move the resistor connection to each exposed
or more sensitivity.)
metal part, particularly any exposed metal part
having
a
return
path
to
the
chassis,
and
meausre
the AC
voltage
across the resistor.
Now,
reverse
the
plug
in the AC
outlet
and
repeat
each
measurement.
Any
voltage
measured
must
not
exceed
0.75 V AC
(r.m.s.).
This corresponds to 0.5 mA AC (r.m.s.).
Place this
probe on
each exposed
15002
10W
metal
part.
Good earth ground
Warning
1. This equipment has been designed and manufactured to meet international safety standards.
2. It is the legal responsibility of the repairer to ensure that these safety standards are
maintained.
3. Repairs must be made in accordance with the relevant safety standards.
4. It is essential that safety critical components are replaced by approved parts.
5. If mains voltage selector is provided, check setting for local voltage.
1-2 (No.20423)
Advertisement
Table of Contents
