Table of Contents
Advertisement
% 'DPSHU $GMXVWPHQW
The tension on the Dauntless FlexBurn's damper is adjustable
to compensate for compression of the gasket that seals the
GDPSHU WR WKH XSSHU ¿UHEDFN 7R DGMXVW WKH GDPSHU
1. Remove the griddle. Loosen the lock nut at the center of
the damper, Figure 3.3.
2. Turn the pressure screw approximately one half turn
clockwise with an Allen wrench provided with your stove.
3. Tighten the lock nut. Prevent the pressure screw from
WXUQLQJ DV \RX WLJKWHQ WKH QXW 5HWHVW WKH GDPSHU
Adjusting Screw
)LJXUH $GMXVW WKH GDPSHU ZLWK WKH $OOHQ ZUHQFK
7LJKWHQ WKH 'DPSHU +DQGOH DV 1HHGHG
A handle on the left side of the stove controls the damper.
The handle attaches to the damper rod with a set screw.
Periodically check the set screw and tighten as necessary.
& 'RRU /DWFK $GMXVWPHQW
The front door of the stove should close securely to prevent
accidental opening and should close tightly to prevent air
IURP OHDNLQJ LQWR WKH ¿UH FKDPEHU 7KH GRRU KDQGOH ZLOO EH
positioned vertically when the door is closed.
2YHU D SHULRG RI WLPH WKH JDVNHW DURXQG WKH GRRU ZLOO
compress and the latch may need adjustment. To adjust the
handle, follow this procedure:
5HPRYH DQG UHWDLQ WKH ORFN QXW ZLWK D ZUHQFK )LJXUH
3.4.
/RRVHQ WKH VHW VFUHZ ZLWK D $OOHQ ZUHQFK
3. Rotate the pawl 180°. Replace the lock nut. Tighten the
set screw, Figure 3.4.
$GGLWLRQDO DGMXVWPHQW FDQ EH PDGH E\ UHPRYLQJ WKH ÀDW
ZDVKHU 2U DQ\ FRPELQDWLRQ RI ZDVKHU UHPRYDO DQGRU
pawl rotation.
Test the door seal. Close the door on a dollar bill and attempt
WR SXOO LW IUHH ,I WKH ELOO LV IUHHG ZLWK OLWWOH UHVLVWDQFH WKH
gasket isn't snug enough at that spot. Continue to make
small adjustments until the setting is right.
,I DGGLWLRQDO DGMXVWLQJ RI WKH ODWFK GRHV QRW HQDEOH WKH GRRU
WR VHDO VX FLHQWO\ LQ RQH DUHD WU\ DGMXVWLQJ WKH JDVNHW LQ WKDW
area. Pack more cement or a smaller diameter gasket into the
channel beneath the gasket so the main gasket is raised and
PDNHV FRQWDFW ZLWK WKH GRRU IUDPH ,I WKLV SURFHGXUH GRHVQ¶W
VROYH WKH SUREOHP UHSODFH WKH JDVNHW ,QVWUXFWLRQV IRU JDVNHW
replacement are given later in this section.
16
(as Needed)
Lock Nut
Damper
Vermont Castings • Dauntless FlexBurn Owner's Manual_R17 • 2020 - ___ • 09/23
Roller
Lock Nut
Set Screw
Flat Washer
)LJXUH 5RWDWH SDZO DQGRU UHPRYH ÀDW ZDVKHU WR DGMXVW ODWFK
' *DVNHW 5HSODFHPHQW
Your Dauntless FlexBurn
make a tight seal between some parts. With use, particularly
on moving parts, gaskets can become brittle and compressed
DQG FDQ EHJLQ WR ORVH WKHLU H HFWLYHQHVV 7KHVH ZLOO QHHG
periodic replacement.
The sizes of replaceable gasket are listed below, along with
their applications.
*DVNHW 'LDPHWHU$QG WKH 3DUWV LW 6HDOV
7KH JULGGOH WR WKH VWRYH WRS ZLUH UHLQIRUFHG JDVNHW
7KH GDPSHU WR WKH GDPSHU IUDPH
7KH IURQW GRRUV WR WKH VWRYH IURQW DQG WKH GRRUV WR
each other.
7KH DVK GRRU WR WKH IURQW RI WKH ERWWRP SDQHO
7KH RXWHU JODVV SDQHV WR WKH GRRU
,I \RX QHHG WR FKDQJH D JDVNHW ¿UVW REWDLQ DQ DSSURSULDWH
replacement from your Vermont Castings' Authorized Dealer.
:DLW XQWLO WKH ¿UH LV RXW DQG WKH VWRYH KDV FRROHG %H VXUH WR
follow the standard safety procedure for working with dusty
materials: wear safety goggles and a dust mask.
The procedure for replacing gaskets is the same, regardless
of the gasket location. Follow these steps:
1. Remove the existing gasket by grasping an end and pulling
¿UPO\ )LJXUH
)LJXUH 5HPRYH JDVNHW WKHQ FOHDQ FKDQQHO ZLWK ZLUH EUXVK
Shoulder Screw
+DQGOH 6WXE
(as needed)
®
XVHV ¿EHUJODVV URSH JDVNHWV WR
3-90-586000C
Advertisement
Table of Contents
