Installing the Phone Choosing the Best Location When.choosing.a.location.for.your.new.phone,.here.are.some.important.guidelines.you.should.consider: PLACE YOUR BASE • Microwave ovens • Refrigerators Near an AC outlet and a telephone wall jack. • TVs • TVs • Other electronics • Other electronics In a centrally-located • Direct sunlight •...
Installing the Battery Use.only.the.Uniden.BT-1007.or.BT-1015.rechargeable.battery.pack.supplied.with.your.cordless.telephone. Unpack all handsets, battery packs, and battery covers. (If the battery cover is on the handset, press in on the notch and slide the cover off.) Line up the battery pack connector with the jack inside the handset.
Connecting the AC adapter To the base To.avoid.risk.of.fire.and.shock,.only.use.the.Uniden.PS-0035.AC.adapter.with.the.base. Connect the AC adapter to the AC IN 8V jack on the back of the base. To the DCX150 charging cradle (for multi-handset packs only) Connect the AC adapter to the Use.only.the.Uniden AC IN 8V jack as shown.
Charging the Handset Place the handset in the base cradle with the display facing forward. If you have an accessory handset, place it in the charging cradle with the display facing forward. Make sure that the charge LED illuminates when the handset is seated.
Connecting to the Phone Line Make.sure.that.the.battery.pack.is.fully.charged. Connect the telephone cord to the TEL LINE jack. Do.you.have.DSL.or.any.high-speed.Internet. service.delivered.through.your.phone.line? Try.putting.a.DSL.filter.between.the.base.and. the.wall.jack..Without.a.filter,.telephone-line- based.Internet.services.can.interfere.with. standard.phones. Connect the telephone cord to a telephone wall jack. Telephone cord DSL filter What if Check TEL Line appears on the...
Changing the dial mode Your.phone.can.communicate.with.the.telephone.network.in.two.different.ways:.tone.dialing.or.pulse.dialing..These. days,.most.base.networks.use.a.method.called.tone.dialing,.so.your.phone.comes.programmed.for.tone.dialing..If. your.phone.company.uses.pulse.dialing,.you.will.need.to.change.your.phone’s.dial.mode..If.you.don’t.get.a.dial.tone. or.can’t.connect.to.the.telephone.network,.please.follow.the.steps.below.to.modify.your.phone’s.settings: 1).Press.MENU/SELECT.. 2).Select.the.Global Setup.menu,.and.then.the.Dial Mode.submenu. 3).Scroll. .to.highlight.Pulse. 4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone. If.you.ever.need.to.change.the.dial.mode.back.to.tone.dialing,.follow.the.same.procedure,.but.select.Tone.in.step.3. NOW YOU ARE READY TO USE YOUR PHONE!
Using the Interface Reading the Display In standby Handset ID and banner Number of new Caller ID calls received The.ringer off.icon.indicates.that.the.ringer.is.turned.off. The.voice mail.icon.appears.when.you.have.messages.waiting.in.your.voice.mailbox. The.privacy.icon.appears.when.the.Privacy.Mode.is.turned.on. The.speaker.icon.appears.when.the.speaker.phone.is.in.use. The.T-coil.icon.appears.when.the.T-coil.Mode.is.turned.on. The.mute.icon.appears.while.the.microphone.is.muted. The.battery.icon.indicates.the.handset.battery.status:.full,.medium,.low,.and.empty. During a call Time Call duration...
Using the Four-way Function Key Your.handset.has.a.four-way.function.key.that. allows.you.to.move.the.cursor.on.the.display.and. access.the.most.commonly.used.features.at.the. touch.of.a.button. •.Press.the.left.side.of.the.key.to.open.the. phonebook. •.Press.the.right.side.of.the.key.to.open.the. Caller.ID.list.. •.Press.the.top.of.the.key.to.increase.the.ringer. volume.(while.the.phone.is.in.standby).or. speaker.volume.(while.you.are.on.a.call). •.Press.the.bottom.of.the.key.to.decrease.the. ringer.volume.(while.the.phone.is.in.standby). or.speaker.volume.(while.you.are.on.a.call). Using the Handset Menu •.To.open.the.menu,.press.the.MENU/SELECT.key. •.The.arrow.cursor.on.the.left.side.of.the.line.shows.which.menu.item.is.currently.highlighted..Use. way.function.key.to.move.the.cursor.up.and. •.To.select.the.highlighted.option,.press.MENU/SELECT. •.To.go.back.to.the.previous.screen,.press.left.on.the.four-way.function.key. •.To.exit.the.menu,.press.END. •.If.you.don’t.press.any.keys.for.thirty.seconds,.the.phone.will.time.out.and.exit.the.menu..(When.setting.the.day. and.time,.the.time-out.period.is.extended.to.two.minutes.) •.For.Ans..Setup,.Global Setup.and.Day & Time.menu.options,.make.sure.the.line.is.not.in.use.and.the.handsets. are.within.range.of.the.base. Increase the volume Open the phonebook Four-way Function Key...
Activating Personal Ring You.can.assign.special.ringer.tones.to.anyone.in.your.phonebook..When.your.phone.gets.a.call,.it.looks.up.the. Caller.ID.information.in.your.phonebook..If.you’ve.assigned.a.personal.ringer.to.that.number,.the.phone.uses.it.so. you.know.who.is.calling..To.turn.the.personal.ringing.on.or.off,.follow.these.steps: 1).Press.MENU/SELECT.. 2).Select.the.Handset Setup.menu,.and.then.the.Personal Ring.submenu. 3).Move.the.cursor.to.select.On.or.Off. 4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone. Activating the Key Touch Tone Key.Touch.Tone.is.the.tone.your.keypad.makes.when.keys.are.pressed..You.can.turn.this.tone.on.or.off. 1).Press.MENU/SELECT.. 2).Select.the.Handset Setup.menu,.and.then.the.Key Touch Tone. submenu. 3).Move.the.cursor.to.select.On.or.Off. 4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone. K e y T o u c h T o n e O f f...
Setting Up the Phonebook Each.handset.has.its.own.separate.phonebook.that.holds.up.to.seventy.names.and.numbers..When.a.handset’s. phonebook.is.full,.the.handset.beeps.and.shows.Memory Full.on.the.display..You.cannot.add.any.names.and. numbers.in.that.handset’s.phonebook.until.you.delete.some.of.the.existing.ones. You.can.also.use.the.phonebook.entries.to.store.a.group.of.numbers.(up.to.twenty.digits).that.you.may.need.to.enter. once.your.call.connects..This.is.referred.to.as.chain.dialing..(See.Chain.dialing.from.the.phonebook.on.page.32.) Creating Phonebook Entries To.store.names.and.numbers.in.your.phonebook,.please.follow.these.steps: 1).With.the.phone.in.standby,.press. 2).To.create.a.new.phonebook.entry,.press.MENU/SELECT..Select.the.Create New.menu..Edit Name.appears. 3).Enter the name for this entry (EDIT NAME).. Use.the.keypad.to.enter.a.name.for.this.entry;.the.name.can.contain.up.to.sixteen.characters..(See.Entering. Text.from.Your.Handset.on.page.22.for.instructions.on.entering.text.).If.you.do.not.want.to.enter.a.name.for.this. entry,.your.phone.will.store.this.entry.as.No Name..Press.MENU/SELECT.when.you.are.finished. 4).Enter the number for this entry (EDIT NUMBER). Once.you.have.stored.a.name,.Edit Number.appears.next..Use.the.number. keypad.to.enter.the.phone.number;.the.phone.number.can.contain.up.to.
Storing Caller ID or Redial Numbers in the Phonebook You.can.store.Caller.ID.records.or.redial.numbers.in.the.phonebook.so.you.can.use.them.later..Go.to.the.Caller.ID.or. redial.list.and.select.the.number.you.want.to.store..(If.the.Caller.ID.information.did.not.include.the.number,.then.you. will.not.be.able.to.store.it.) 1).With.the.phone.in.standby,.press. 2).Use. .and. .to.scroll.through.the.Caller.ID.records.or.redial.numbers..When.you.come.to.the.information.you. want.to.store,.press.MENU/SELECT.. Note:..If.you.need.to.add.(or.delete).a.“1”.to.the.beginning.of.the.Caller.ID.phone.number,.press. /ToNE.(see. page.33)..If.you.need.to.add.(or.delete).the.stored.area.code.to.the.Caller.ID.phone.number,.press.#.(see. page.34). 3).Select.Store into PB..Edit Name.appears..If.the.phone.number.is.already.stored.in.memory,.you.will.hear.a. beep,.and.This data is already saved!.appears.in.the.display..The.number.will.not.be.stored. 4).Continue.by.following.the.steps.for.Creating.Phonebook.Entries.on.page.25. Deleting a Single Phonebook Entry 1).With.the.phone.in.standby,.press. 2).Find.the.entry.that.you.want.to.delete.and.press.MENU/SELECT.. 3).Select.Delete..Delete Entry?.appears.in.the.display. 4).Move.the.cursor.to.select.Yes.
Using Your Phone From a cordless handset 1).Pick.up.the.handset.from.the.cradle. 2).Press.TALK/FLASH. 3).Listen.for.the.dial.tone. 4).Dial.the.number. Making a call 1).Pick.up.the.handset.from.the.cradle. 2).Dial.the.number. 3).Press.TALK/FLASH. 1).Pick.up.the.handset..(If.AutoTalk.is.on,.the. phone.will.answer.when.you.pick.up.the. handset.from.the.cradle.) Answering a call 2).Press.TALK/FLASH..(If.Any.Key.Answer.is. on,.you.can.also.press.any.key.on.the.dial. pad.) Hanging up Press.END.or.return.the.handset.to.the.cradle. From a handset speakerphone 1).Pick.up.the.handset.from.the.cradle. 2).Press. 3).Listen.for.the.dial.tone. 4).Dial.the.number. 1).Pick.up.the.handset.from.the.cradle. 2).Dial.the.number.. 3).Press. 1).Pick.up.the.handset..
Making a Call from the Phonebook 1).With.the.phone.in.standby,.press. 2).Find.the.phonebook.entry.you.want.to.call.(see.Finding.a.Phonebook.Entry.on.page.26). 3).Press.TALK/FLASH.or. .to.dial.the.number. Note:. You.can.also.press.TALK/FLASH.or. dial,.and.then.press.MENU/SELECT. Chain dialing from the phonebook If.you.often.have.to.enter.a.series.of.digits.or.a.code.number.during.a.call,.you.can.save.that.code.number.to.a. phonebook.entry..When.your.call.connects,.just.use.the.phonebook.to.transmit.the.saved.code.number..(This.is. referred.to.as.chain.dialing.). 1).Enter.the.code.number.(up.to.twenty.digits).into.the.phonebook.(see.Creating.Phonebook.Entries.on.page.25).. Be.sure.to.enter.the.code.number.into.the.phonebook.exactly.as.you.would.enter.it.during.a.call.. 2).During.a.call,.when.you.hear.the.prompt.that.tells.you.to.enter.the.code.number,.press. 3).Use. .or. .to.select.the.phonebook.entry.that.contains.the.digits.you.want.to.send. 4).Press.MENU/SELECT..The.phone.sends.the.digits.of.the.code.number.exactly.as.you.saved.them.in.the. phonebook.entry. Switching to the Handset Speakerphone During a Call To.switch.a.normal.call.to.the.speakerphone,.press. normal.call,.press. .to.open.the.phonebook. .before.you.open.the.phonebook..Find.the.phone.number.you.want.to.
Using Caller ID, Call Waiting, and Redial Lists If.you.subscribe.to.Caller.ID.service.from.your.phone.company,.your.phone.will.show.you.the.caller’s.phone.number. and.name.(if.available).whenever.a.call.comes.in..If.you.subscribe.to.Caller.ID.on.Call.Waiting,.the.phone.will.also. show.you.the.name.and.the.number.of.any.call.that.comes.in.while.you’re.on.the.line. Using the Caller ID List You.can.store.up.to.thirty.Caller.ID.numbers.in.each.handset..Caller.ID.records. are.stored.from.newest.to.oldest..Once.your.Caller.ID.list.is.full,.the.oldest. record.will.be.automatically.deleted.when.a.new.call.is.received..When.you. have.new.Caller.ID.records.(that.is,.records.you.have.not.reviewed.yet).and.the. phone.is.in.standby,.the.handset.will.display.the.number.of.new.Caller.ID.calls. received..(See.page.20.) To.open.the.Caller.ID.list,.press. Use. .and. to.scroll.through.the.list..(New.records.have.an.asterisk.next.to.the.received.time.) Making a Call from a Caller ID Record 1).With.the.phone.in.standby,.press. 2).Use. .and. .to.find.the.Caller.ID.record.you.want.to.dial. 3).If.you.need.to.add.(or.delete).a.“1”.to.the.beginning.of.the.displayed.phone.number,.press. /ToNE.. 4).Press.TALK/FLASH.or.
Finding a Lost Handset To.locate.a.misplaced.handset,.press.FiND.on.the.base.when.the.phone.is.in.standby..The.handsets.connected.to. the.paging.base.will.beep.for.one.minute,.and.PAGING.appears.on.the.handset.display..To.cancel.paging,.press. FiND.again.or.any.key.on.the.found.handset. Note:.. Handsets.that.are.not.currently.connected.to.this.base.will.not.be.paged. Using Hold, Conference and Transfer Placing a Call on Hold 1).During.a.call,.press.CLEAr/iNT’CoM.to.place.the.caller.on.hold..If.you.leave.a.caller.on.hold.for.more.than.ten. seconds,.the.display.screen.will.read,.Line On Hold. 2).To.return.to.the.party.on.hold,.press.TALK/FLASH.or. Notes:.•.You.can.only.place.a.caller.on.hold.for.five.minutes..Once.five.minutes.has.passed,.that.party’s.line.will.be. disconnected.and.the.phone.will.return.to.standby. •.While.a.call.is.on.hold,.Call.Waiting.and.CID.on.Call. Waiting.do.not.work.. Conferencing If.you.have.more.than.one.handset,.up.to.three.people.can. participate.in.a.conference.call..A.three-way.conference.call. consists.of.an.outside.line.and.two.handsets..You.can.easily. join.a.call.already.in.progress..The.handsets.must.be.currently. connected.to.the.same.base.(see.page.15). 1).Press.TALK/FLASH.or. .to.join.the.call. 2).To.hang.up,.return.the.handset.to.the.cradle.or.press.END.. The.other.party.will.still.be.connected.to.the.call. ..The.phone.will.return.to.the.holding.party. Handset #2 Handset #1 Outside call...
4).To keep this greeting:. To switch to the other greeting:. Press.6.while.the.system.is.playing.the.current.greeting. 5).Each.time.you.press.6,.the.system.switches.between.the.pre-recorded.and.the.personal.greeting..The.last. greeting.you.hear.is.used.as.the.current.greeting. Deleting Your Personal Greeting You.can.delete.your.personal.greeting.from.the.base..You.cannot.delete.the.pre-recorded.greeting. 1).Press. /MUTE..The.system.announces.the.number.of.new.and.old.messages,.then.starts.to.play.the. messages.unless.it.has.no.messages.. 2).Press.5.to.stop.the.announcements.or.message.playback..You.will.hear.intermittent.beeps.indicating.that.the. system.is.in.the.command.waiting.mode. 3).Press.6..The.system.plays.the.current.greeting..Switch.to.your.personal.greeting.if.necessary..(See.the.previous. section.to.switch.the.greeting.) 4).While.the.personal.greeting.is.playing,.press.4. 5).The.system.announces.“Greeting.has.been.deleted,”.and.switches.back.to.the.pre-recorded.greeting. Selecting the Language for Announcements You.can.select.the.language.of.your.answering.system.announcements..The.default.system.language.is.English. 1).Press.MENU/SELECT.. 2).Select.Ans. Setup,.and.then.the.Ans. Language.submenu. 3).Move.the.cursor.to.choose.a.language.. for US models:.. Choose.English.or.Español.(Spanish).
Using the Answering System Turning Your Answering System On and Off From the base 1).With.the.phone.in.standby,.press.. ANSWEr oN/oFF. 2).The.system.announces.“Answering.System. is.on”.and.plays.the.current.greeting. Turning.On 3).The.message counter.LED.displays.the. number.of.messages.stored.in.memory.. If.the.counter.flashes,.then.you.have.new. messages.waiting. 1).With.the.phone.in.standby,.press.. ANSWEr oN/oFF. 2).The.phone.announces.“Answering.System. Turning.Off is.off.” 3).The.message counter.LED.is.no.longer. illuminated. Notes:.•.If.the.answering.system.announces.“No.remaining.time”.when.you.turn.it.on,.the.memory.is.full.(the. message counter.LED.also.shows.FL)..The.answering.system.can’t.record.any.new.messages.until.you. delete.some.of.the.saved.ones. •.If.you.do.not.set.the.clock,.your.messages.may.not.have.the.correct.day.and.time.stamp..To.set.the.clock,. see.page.23. From the handset 1).Press.MENU/SELECT..
Remote Operation from the Handset You.can.operate.your.answering.system.from.the.handset.whenever.the.phone.is.in.standby. /MUTE.to.start.remote.operation. •.Press. •.During.remote.operation,.the.phone.beeps.to.let.you. know.it’s.waiting.for.your.next.command. •.Press.the.number.listed.next.to.the.commands..(see.the. table.for.a.list.of.all.available.commands).. •.Use.the.left.and.right.keys.to.scroll.through.the. commands.(see.the.table.for.a.list.of.all.available. commands),.and.press.MENU/SELECT..You.can.also. press.the.number.listed.next.to.the.commands.instead.of. scrolling.through.them. •.When.you’re.finished,.press.END.or.just.hang.up. •.If.you.don’t.press.any.keys.for.thirty.seconds,.the.phone. will.return.to.standby. Command Use it to 1:Repeat Repeat a message 2:Play Play messages 3:Skip Skip a message 4:Delete Delete a message 5:Stop Stop the current operation 6:SelectGreeting Choose a greeting...
•.To.mute.the.call.screen.and.allow.the.caller. to.continue.leaving.the.message,.press. Turning Off the Message Alert Tone When.all.new.messages.are.played.back,.the.message.alert.tone.will.automatically.deactivate..The.tone.will.not. deactivate.until.all.new.messages.are.played.back..To.quickly.turn.off.the.tone,.press.any.key.on.the.base. Operating the Answering System While You Are Away from Home When.you.are.away.from.home,.you.can.operate.your.answering.system.with.any.touch-tone.telephone. Setting a security code or Personal Identification Number (PIN) To.operate.your.answering.system.when.you.are.away.from.home,.you.will.need.to.enter.a.two-digit.security.code.or. Personal.Identification.Number.(PIN)..The.default.security.code.is.80. 1).Press.MENU/SELECT.. 2).Select.the.Ans. Setup.menu,.and.then.the.Security Code.submenu. 3).Use.the.number.keypad.(0.through.9).to.enter.a.two-digit.security.code.(01-99). 4).Press.MENU/SELECT..You.will.hear.a.confirmation.tone..
Page 51
To.operate.from.a.remote.location,.use.any.touch-tone.telephone,.and.follow.these.steps: 1).Call.your.telephone.number.and.wait.for.the.system.to.answer..If.the.answering.system.is.off,.it.will.answer.after. about.ten.rings.and.sounds.a.series.of.beeps. 2).During.the.greeting.or.the.beeps.(if.answering.system.is.off),.press.0.and.enter.your.security.code/PIN.within. two.seconds. 3).The.answering.system.announces.the.current.time.and.the.number.of.messages.stored.in.memory.. You.hear.“To.play.incoming.messages,.press.zero-two..For.help,.press.one-zero”.followed.by.a.beep. 4).Enter.a.remote.command.from.the.chart.below..You.have.fifteen.seconds.to.enter.the.first.command;.after.the. first.command,.you.have.two.seconds.to.enter.each.command. If you want to Press 0.then.2. The.answering.system.plays.back. Play.incoming. messages.for.four.minutes,.then. messages waits.for.another.command..To. continue.playing.your.messages,. press.0.then.2.again. 0.then.1.(after.the.first.four. Repeat.this.message. seconds.of.this.message) Go.back.to.the. 0.then.1.during.the.first.four. previous.message seconds.of.a.message. Skip.this.message 0.then.3 Delete.this.message 0.then.4 5).When.you.finish,.you.will.hear.intermittent.beeps.indicating.that.the.system.is.in.the.command.waiting.mode.. Enter.another.command.from.the.chart.within.fifteen.seconds. 6).Hang.up.to.exit.the.system..The.answering.system.automatically.returns.to.its.normal.standby.setting. If you want to Stop.the.current.operation.to.
Tuck the excess cord into the open space in the bracket. Route the telephone cord through the hole of the wall-mount bracket. Connect the AC adapter and the telephone cords as shown on pages 8 and 10.
Page 53
Place the mounting slots over the pins on the wall plate. Slide the base down to lock it into place. Removing the wall-mount bracket At the bottom of the base, pinch the two "nose" of the wall-mount bracket as shown, and then slide the bracket away from the base.
Maintenance Specifications Operating temperature AC adapter Battery pack Notes: •.Use.only.the.supplied.AC.adapters. •.Be.sure.to.use.the.proper.adapter.for.the.base.and.any.chargers. •.Do.not.place.the.power.cord.where.it.creates.a.trip.hazard.or.where.it.could.become.chafed.and.create.a.fire.or. electrical.hazard. •.Do.not.place.the.base.in.direct.sunlight.or.subject.it.to.high.temperatures. Battery Information Battery life With.average.use,.your.handset.battery.provides.more.than.ten.hours.of.talk.time.and.approximately.seven.days. of.standby.time..You.can.achieve.optimum.battery.life.and.performance.by.returning.the.handset.to.the.base.or. charging.cradle.after.each.use..When.your.handset.is.left.off.of.the.cradle,.the.battery.will.gradually.discharge.even. if.the.handset.is.not.being.used..The.actual.talk.time.duration.will.be.reduced.in.proportion.to.the.amount.of.time.the. handset.is.off.of.the.cradle. 32°.F.to.122°.F.(0°.C.to.50°.C) Base Part number PS-0035 Input voltage 120V.AC,.60.Hz Output voltage 8V.DC.@.300mA Part number BT-1007 Capacity 500mAh,.2.4V.DC Charging cradle PS-0035 120V.AC,.60.Hz 8V.DC.@.300mA...
5).When.the.base.information.is.deleted,.the.handset.displays.Handset not registered-place handset on base to register. See your Owner’s Manual for help. 6).Re-register.the.handset.to.the.base.(see.Registering.accessory.handsets.on.page.13).. If.the.handset.cannot.contact.the.base,.it.will.display.Out Of Range..Make.sure.the.handset.is.in.range.of.the.base. and.the.base.is.connected.to.power;.you.can.also.reset.the.handset.without.the.base.(see.the.next.section). Resetting the Handset Without the Base If.your.original.base.is.not.available.for.some.reason,.you.can.still.reset.the.handset.and.use.it.with.another.base. 1).Press.and.hold.END.and.#.for.at.least.five.seconds. 2).Move.the.cursor.to.select.Base Unavailable.and.then.press.MENU/SELECT. 3).Select.the.base.which.you.want.to.de-register.from,.and.then.press.MENU/SELECT..Base Unavailable.appears. 4).Move.the.cursor.to.select.Yes,.and.then.press.MENU/SELECT..You.hear.a.confirmation.tone,.and.the.handset. deletes.its.own.base.information.without.contacting.the.base..If.the.handset.was.registered.to.only.one.base,. it.displays.Handset not registered-place handset on base to register. See your Owner’s Manual for help..If.the. handset.is.still.registered.to.another.base,.it.searches.for.the.other.base.and.then.returns.to.standby.
Changing the Line Mode for Multiple Extensions Line.mode.refers.to.the.method.that.telephones.use.to.signal.each.other.that.an.extension.is.in.use..Customer. service.may.recommend.changing.the.line.mode.if.you.have.any.of.the.following.problems: •.Your.phone.keeps.ringing.after.someone.answers.on.an.extension.phone. •.Your.answering.system.doesn’t.stop.recording.when.you.answer.on.an.extension.phone. •.Caller.ID.displays.briefly.and.then.clears. 1).If.you.have.multiple.bases,.select.the.base.that.is.having.problems.(see.page.15). 2).Press.MENU/SELECT.. 3).Select.the.Global Setup.menu,.and.then.the.Set Line Mode.submenu.. 4).If Instructed by Customer Service Press [select].appears..Press.MENU/SELECT. 5).Move.the.cursor.to.select.Type - A,.Type - B,.or.Off. 6).Press.MENU/SELECT..You.will.hear.a.confirmation.tone. Traveling Out of Range When.the.handset.is.in.standby,.the.handset.will.display.Out Of Range. During.a.call,.if.you.move.your.handset.too.far.from.your.base,.noise.may.increase..If.you.pass.the.range.limit.of.the. base,.the.handset.will.beep,.display.Out Of Range,.and.then.go.to.standby..The.base.will.maintain.the.connection. for.thirty.seconds.after.the.handset.goes.out.of.range..If.you.move.the.handset.back.within.range.of.the.base.within.
Liquid Damage Moisture.and.liquid.can.damage.your.cordless.phone. •.If.the.handset.or.base.is.exposed.to.moisture.or.liquid,.but.only.the.exterior.plastic.housing.is.affected,.wipe.off. the.liquid,.and.use.as.normal.. •.If.moisture.or.liquid.has.entered.the.plastic.housing.(i.e..liquid.can.be.heard.in.the.phone.or.liquid.has.entered.the. handset.battery.compartment.or.vent.openings.on.the.base),.follow.the.steps.below..After.following.these.steps,.if. your.cordless.telephone.does.not.work,.please.call.our.Customer.Service.Hotline.(see.the.back.cover.page). Handset 1).Remove.the.battery.cover.and.leave.it.off.for. ventilation. 2).Disconnect.the.battery.pack..Leave.the.battery. cover.off.and.the.battery.pack.disconnected.for.at. least.3.days. 3).Once.the.handset.is.completely.dry,.reconnect.the. battery.pack.and.the.battery.cover. 4).Recharge.the.handset’s.battery.pack.for.15.to.20. hours.before.using.. IMPORTANT:.You.must.unplug.the.telephone.line.while.recharging.the.battery.packs.to.avoid.charge.interruption. CAUTION: DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven.
REMOTE OPERATION CARD Remote access Turn on the answering away from home system remotely 1. Call your phone number from a 1. Call your phone and let it ring touch-tone phone. 10 times until you hear a beep. 2. During the outgoing message, 2.
Page 72
C U T Task Repeat a Message Play Incoming Messages Skip a Message Delete a Message Stop Operation Answering System On Answering System Off Help C U T Task Repeat a Message Play Incoming Messages Skip a Message Delete a Message Stop Operation Answering System On Answering System Off...