Test Mode - Roland HandSonic 10 Service Notes

Mar. 2006
When the receiving is completed, the message of "Updating: 1/8"
appears and the writing of the receiving data begins.
The [KIT] LED is turned off.
The [EFFECT] LED is turned on.
After writing data for one file is completed, the message of "Updating: ok
1/8" appears.
The [EFFECT] LED is turned off.
The LED corresponding to block (file) is turned on.
[1 (CONGA)] Block 1
[2 (TABLA)] Block 2
[3 (STEEL DRUM)] Block 3
[4 (DRUMS)] Block 4
[5 (SFX)] Block 5
[TUNING] Block 6
Block 7
[MUFFLING]
[EFFECT] Block 8
After writing data for one file is completed, HPD-10 will be on stand-by
waiting for next data and shows message "Waiting: 2/8."
4.
Play back the second SMF file.
5.
Repeat the step 3 and 4 to complete the all update procedures of eight
files.
If the all data is received and checksum is right, the message of
"Completed! v*.**" will appear. And the version will appear in the right
side of the LCD display.
Error messages
• LED corresponding to the block in which any errors occur on system
updating blinks.
[1 (CONGA)] Block 1
[2 (TABLA)] Block 2
[3 (STEEL DRUM)] Block 3
[4 (DRUMS)] Block 4
[5 (SFX)] Block 5
[TUNING] Block 6
[MUFFLING] Block 7
Block 8
[EFFECT]
• Block Checksum Error
"Error!: Blocksum"
Checksum of the block into which data received is wrong.
• Flash Memory Erase Error
"Error!: Erase"
A mistake is made on erasing flash memory.
• Flash Memory Write Error
"Error!: Write"
A mistake is made on writing flash memory.
• Total Checksum Error
"Error!: TotalSum"
Checksums of the data in all block are wrong.
6.
Turn off and on the power of HPD-10, carry out the test mode procedure.
Recovering of a mistake for system
updating
Turn off the power of HPD-10, and carry out the updating procedure.
14

Test Mode

Items Required
• PD-8 x 2
• FS-5U x 2
• drum stick
• MIDI cable
• PCS-31
• stereo cable
• headphones
• monitor speaker x 2
• oscillator or audio equipment (portable CD player, etc.)
Contents of the User Memory are need to be deleted after Test Mode. Make a
backup of User Data with bulkdump function before updating.
Entering Test Mode
While holding down [EFFECT], [3 (STEEDRUM)] and [EDIT] at the same time,
turn on the power switch. Hold down [EFFECT], [3 (STEELDRUM)] and
[EDIT] until the following message appears in the LCD display.
HPD-10 Service
Press [ ], and next press [ ]. Then you've entered the test mode.
* If you press the wrong switches or press them in wrong order, you cannot enter
the test mode. Then return back to the first step.
Exiting Test Mode
You can exit from any section of Test Mode by turning off the power; however,
you have to carry out the Factory Reset after finishing Test Mode procedure.
Test Items
(1) Version [1. Version]
(2) Device Test [2. Device]
(3) MIDI Test [3. MIDI]
(4) Foot Switch Test [4. Foot Switch]
(5) Ext Trigger Test [5. Ext Trigger]
(6) Sound Test [6. Sound]
(7) Switch/LED Test [7. Switch & LED]
(8) Encoder/LCD Test [8. Encoder & LCD]
(9) Pad Pressure Test [9. Pad Pressure]
(10) Pad Velocity Test [10. Pad Velocity]
(11) D-Beam Test [11. D-Beam]
(12) Factory Reset [12. Factory Reset]
Skipping
• Skip to the next test item:
• Skip to the previous test item:
• Re-do the current test item:
• Re-do the current NG test item:
HPD-10
[SHIFT] + [+] or [SHIFT] + [ ]
[SHIFT] + [-] or [SHIFT] + [ ]
[SHIFT] + [ ]
[SHIFT] + [ ]