Table of Contents
Advertisement
KV-25DXR
RM-727/APM-X3U
1-4. OPERATION
Preparation
Make sure the following are properly set.
• On-screen "VIDEO 1 2 or 3" "EXT-A" or "RGB" * in-
dicators and the RdB or VIDEO lamp should be off.
(Press TV/VIDEO button or RGB button as many
times as necessary until they go out.)
• AUTO STEREO selector should be set to ON
(depressed).
Depending on the channel to be viewed, check the
following and change as necessary.
• CABLE ON/OFF button
For VHF and UHF channels, set to OFF n.
For cable TV channels, set to ON
=·
• On-screen "AUX"* indicator
(Press ANT/AUX button to change as necessary.)
For VHF, UHF and regular cable TV channels:
The indicator should be off.
For pay cable TV channels:
The indicator should be displayed.
*The displays, "VIDEO", "EXT-A", "RGB" or "AUX" indicate
that signals fed in through the VIDEO 1/3 INPUT jacks,
VIDEO 2 IN AV uniconnector, the external audio jacks, the
RGB MULTI INPUT connector or through the AUX terminals
are being received.
1 Press POWER to turn on the TV.
The channel number will be displayed on the screen
and the SLEEP lamp will light up for several seconds.
2 Select channels in one of the following two ways.
• Press the numeral(s) of the channel and then
press ENTER.
Ex. To select channel 6, press 6 and then ENTER.
To select channel 125, press 1, 2, 5 and then
ENTER.
If you pressed a wrong numeral, wait for a few
seconds and it will disappear. Then try again.
• Press CHANNEL "+" for higher-numbered chan-
nels and "-"
for lower-numbered channels. Preset
channels will appear in sequence. (For presetting
desired channels, see page 9.)
The channel display will remain on the screen for a
few seconds. To keep the display on the screen,
press DISPLAY.
3 Adjust the volume and picture to your preference, if
necessary.
Press VOLUME "+" to increase volume, or "-"
to
decrease it.
Press PICTURE "+" to increase picture contrast, or
"-" to decrease it.
To mute the sound immediately, press MUTING. The
"MUTING" display will appear and remain on the
screen. Press it again to restore the sound to its
previously-set level or press VOLUME"+".
To turn off the set, press POWER again.
To have the set turn off automatically after one hour,
press SLEEP. The "SLEEP" display will appear on the
screen a few seconds and the SLEEP lamp on the TV
will remain lit for one hour.
To cancel the sleep timer, press SLEEP again so that
the "SLEEP" display turns off, or turn off the TV.
LISTENING TO MULTICHANNEL TV SOUND(MTS)
BROADCASTS
In the years to come, an increasing number of pro-
grams will be broadcast in stereo. Called Multichan-
nel TV Sound or MTS, the new technology will greatly
enhance TV viewing by bringing you programs with
high fidelity stereo sound. MTS also provides for an
extra channel called the Second Audio Program or
SAP which broadcasters can use to transmit a se-
cond language for bilingual transmissions or some
other sound track.
To receive a stereo program
Normally set the AUTO STEREO selector to ON (de-
pressed). In this position, the STEREO lamp on the TV
will light up whenever a stereo broadcast is received.
To listen to the stereo sound, select the MAIN mode
with the MTS button so that the on-screen MAIN in-
dicator appears. The stereo sound will be heard from
the left and right speakers.
Every push on the MTS button changes the indicator
below the channel number as follows:
MAIN----SAP----BOTH
When there is a SAP (Second Audio Program) broadcast
Select the SAP mode so that the SAP indicator is
displayed and only the SAP sound is heard from both
speakers.
To listen to both MAIN and SAP broadcasts
Select the BOTH mode so that the BOTH indicator is
displayed. The MAIN and SAP sounds come out from
the left and right speakers respectively.
The MAIN sound becomes monaural(mixed) even if it is
a stereo broadcast, as the sound comes only from the
left speaker.
Notes
• The selected mode will be retained even after the
power is once turned off.
• There may be cases of stereo broadcasts where ex-
cessive "noise" will be heard due to a weak incoming
signal. By switching the AUTO STEREO selector to
OFF and returning to a monaural mode, the noise
should be eliminated.
• When the SAP mode is selected and there is no SAP
broadcast, no sound is heard from the speakers. (If
the BOTH mode is selected, the sound is heard only
from the left speaker.)
• SAP broadcasts are always transmitted
with the
MAIN broadcast.
-8-
Advertisement
Table of Contents
