Audio Dubbing (Gr-D93/73 Only); Insert Editing (Gr-D93/73 Only) - JVC GR-D93 Instructions Manual

I Audio Dubbing ( GR-D93/73only)
The audio track can be customized only when recorded
in the t2-bit and SP modes. (_:_pg. 26)
• Use the provided remote control
Stereo Microphone -
STOP
REW
STOP
Speaker
1 Play back the tape to locate the point where editing
will start, then press PAUSE (11).
2 While holding A. DUB (=) on the remote control,
press PAUSE (11). The "1I@" and "MIC" indicators
appear.
3 Press PLAY (1_), then begin "narrating". Speak into
the microphone.
• To pause dubbing, press PAUSE (11).
4 TO end Audio Dubbing, press PAUSE (11), then STOP
(m).
To hear the dubbed sound during playback
Set 'NARRATION" to "ON" or 'MIX". (_J- pg. 25, 28)
NOTES:
• Sound is not heard frol'n the speaker during Audio Dubbfeg.
• When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
• If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
• If feedback or howling occurs during TV playback, move the
camcorder's microphone away from the TV, or turn down
the TV's volume.
• If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective from
the point where 16-bit recording began.
• During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in t 6*bit audio
or a blank portion, Audio Dubbing stops.
• To perform Audio Dubbing while watching on the television,
make connections. (_ pg. 17)
• To perform Audio Dubbing with a video unit connected to
the camcorder's AV connector, first set "S/AV INPUT" to
"ON" in VIDEO Menu. (::_ pg. 25, 28)
The "AUX _ indication appears instead of "MIC".
EDITING EN
37
I InsertEditing (GR-D93/73only)
You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
• Use the provided remote control.
NOTES:
• Before performing the folfewfeg steps, make sure that
'q-IME CODE" is set to "ON". (:_ pg. 25, 28)
• Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
• To perform Insert Editing while watching in the television,
make connections. (_ pg. 17)
1 Play back the tape, locate the Edit-Out point and
press PAUSE (11). Confirm the time code at this point.
(_:- pg. 13)
2 Press REW (.<1<) until the Edit-In point is located,
then press PAUSE (11).
3 Press and hold INSERT (O) on the remote control,
then press PAUSE (11). The '!10" indicator and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
4 Press START/STOP to begin editing.
• Confirm the insert at the time code you checked in step 1.
• TO pause editing, press START/STOP. Press it again to
resume editing.
TO end Insert Editing, press START/STOP, then
STOP (11).
NOTES:
• Program AE with special effects (_: pg. 30) can be used to
spice up the scenes being edited during Insert Editing.
• During Insert Editing, the date and time information
changes.
• If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure you
only edit recorded areas. _,
• During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops. (_-_' p g. 43)