Troubleshooting - JVC GR-D93 Instructions Manual

Advanced f eatures
II[_I [oI_l_lEIZeZ_ll[e]l_411] I_l:.lll.]._ll[_tl I
• FOCUSis set to the Manual mode.
"+ Set Focus to the Auto mode. (;-+" pg. 31 )
• The tens is dirty or covered with condensation.
-+'Clean the Iens and check the focus again. (_ pg. 48)
• The recording was done in a dark place, or the co.mat
was low.
• The Squeeze mode (SQUEEZE) is selected.
4 Disengage the Squeeze (SQUEEZE) mode. (_:_" pg. 25, 26)
I|_riTIPJll_"[_Ei0'_l'l_II[oi¢];,i,.ll_141qti_[
• The light source or the subject does not include white. Or
there are various different light sources behind the subject.
-+Find a white subject and compose your shot so that it atso
appears in the frame. (;.z' pg+ !8, 31)
• The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
-+Disengage the Sepia (SEPIA) and Monotone
(MONOTONE). (,.z' pg+ 25, 31)
IblI+411.p.[+*[+41 _l[r41_ i i_111[ __iEiPJ_ I p.ll f_ll { e i eI+* r;. i I
• Shooting was performed under backlit conditions.
-+Press BACKUGHT. (_¢ pg. 33)
_i]i'_IL_ { i i t "4.* i ri'_ i I [ -.i t I [+411 zi i ITI_,_4 _ I i,_; t i ii 11 ] i Ii +41,,r4 p4 r+4_ i_
• The subject is too bright.
-+ Set '1@] _ to "SPOTUGHT". (_¢ pg. 31 )
• The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
-+Disengage the Sepia (SEPIA) or Monotone (MONOTONE)
mode before setting White Balance. (_-_' p g+ 3t)
• The Power Switch is set to ,,Imp.
-+ Set the Power Switch to '_]". (_-+' p g. 8)
III iFJ t+| R T_[i+_l?J _'31FJ _ t+:+4 _ m :+4.__ [+]_
• The Sepia (SEPIA) or Monotone (MONOTONE) mode is
activated.
-+Disengage the Sepia (SEPIA) and Monotone
(MONOTONE). (,.z' pg+ 25, 31)
• The Power Switch is set to ,,Imp.
-+ Set the Power Switch to '_]". (_-+' p g. 8)
TROUBLESHOOTING, EN
41
Otherproblems
• The temperature of the battery is extremely high/low.
• Charging is difficult in places subject to extremely high/low
temperatures.
-+To protect the battery, it is recommended to charge it in
places with a temperature of 10°C to 35°C (E0°F to 95°F).
(_-_' p g+ 45)
• The date/time is not set.
"_ Set the date/time. (:_ pg+ 8)
• The built+in clock battery has run out and the previously set
date/time has been erased.
-+Consult your nearest JVC dealer for replacement.
ili_+.ll+._ izli¢]_l.tlilt
• The camcorder is not getting power, or some other
malfunction exists.
-+Turn the camcorder's power off and on again. (_ pg+ 8)
• The Power Switch is set to "1_"+
-+ Set the Power Switch to '_]'. (_¢ pg. 8)
-- (GR-D93/73 only) --
• Files stored in the memory card are protected.
-+Remove protection from the files stored in the memory
card _nd delete them. (,,z' pg. 22)
• This is not a malfunction.
-+By recording with "DIS" activated (_++ pg. 25, 26) this can
be avoided.
• The OV cable was plugged/unplugged with power turned
on.
-+Turn the camcorder's power off and on again, then operate
it.
IIi I i -.! 1 +.p;. i I1¢111 _ i"['_.11 IIl_ll JI t I 111111i'_r'_l_ll I-"L'_
{ | I 1+.I li i p. [l [+.I {_T_ _-I _ [P.I | i_ i]I i i {+.l I.'+ I Zt_ i_11 h111_iI_I [l|r+_!
• When shooting inthe dark, the unit becomes highly
sensitive to light when "GAIN UP" is set to "AUTO".
-+ If you want the lighting to Iook more natural, set "GAIN U P"
to "AG C" or "OFF". (_ pg. 25, 26)
• The light used to illuminate the LCD monitor causes it to
become hot.
-'_Close the LCD monitor to turn it off or set the Power Switch
to "OFF", and let the unit cool down.