Audio Dubbing (Gr-D93/73 Only); Insert Editing (Gr-D93/73 Only) - JVC GR-D33 Instructions Manual

Audio Dubbing (GR-D93/73 only)

The audio track can be customized only when recorded
in the 12-bit and SP modes. (
Use the provided remote control.
REW
INSERT
T
STOP
W
1
Play back the tape to locate the point where editing
will start, then press PAUSE (9).
2
While holding A. DUB (D) on the remote control,
press PAUSE (9). The "9D" and "MIC" indicators
appear.
3
Press PLAY (U), then begin "narrating". Speak into
the microphone.
To pause dubbing, press PAUSE (9).
4
To end Audio Dubbing, press PAUSE (9), then STOP
(8).
To hear the dubbed sound during playback
Set "NARRATION" to "ON" or "MIX". (
NOTES:
Sound is not heard from the speaker during Audio Dubbing.
When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
If feedback or howling occurs during TV playback, move the
camcorder's microphone away from the TV, or turn down
the TV's volume.
If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective from
the point where 16-bit recording began.
During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops.
To perform Audio Dubbing while watching on the television,
make connections. ( pg. 17)
To perform Audio Dubbing with a video unit connected to
the camcorder's AV connector, first set "S/AV INPUT" to
"ON" in VIDEO Menu. (
The "AUX" indication appears instead of "MIC".
pg. 26)
Stereo Microphone
PAUSE
START/
STOP
PLAY
A.DUB
Speaker
pg. 25, 28)
pg. 25, 28)

Insert Editing (GR-D93/73 only)

You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
Use the provided remote control.
NOTES:
Before performing the following steps, make sure that
"TIME CODE" is set to "ON". (
Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
To perform Insert Editing while watching in the television,
make connections. ( pg. 17)
1
Play back the tape, locate the Edit-Out point and
press PAUSE (9). Confirm the time code at this point.
( pg. 13)
2
Press REW ( ) until the Edit-In point is located,
3
then press PAUSE (9).
3
Press and hold INSERT (I) on the remote control,
then press PAUSE (9). The "9I" indicator and the Time
Code (min.:sec.) appear and the camcorder enters
Insert-Pause mode.
4
Press START/STOP to begin editing.
Confirm the insert at the time code you checked in step 1.
To pause editing, press START/STOP. Press it again to
resume editing.
5
To end Insert Editing, press START/STOP, then
STOP (8).
NOTES:
Program AE with special effects (
spice up the scenes being edited during Insert Editing.
During Insert Editing, the date and time information
changes.
If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure you
only edit recorded areas.
During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops. ( pg. 43)
EDITING
37
EN
pg. 25, 28)
pg. 30) can be used to