Advertisement
REMOTE CONTROL OPERATION
The accessory Remote Control Unit 1s used to control the amplifier from a convenient distance.
(1)
Inserting the Dry Celt Batteries
Notes on Battery Usage
1, Remove the battery cover on the Remote Control Unit.
@
RC-176 uses the size REP (AA) dry cell batteries.
®@
The batteries will need to be replaced approximately once a year.
This will depend upon how often the Remote Control Unit is used.
©
If, inJess than a year from the time new batteries were inserted, the
Remote Control Unit fails to operate the Amplifier from a near-by
Position, it is time to replace the batteries.
©
Insert the batteries properly, following the polarity diagram inside
the battery compartment.
@
Batteries are prone to damage and leakage. Therefore:
@
Do not mix new batteries with used ones.
2. Insert two dry cell batteries as shown in the diagram on the bat-
@
Do not mix different types of batteries
tery supply unit
®@
Co not jumper opposite poles of the batteries, expose then to
heat, break them open, nor expose them to open fire.
©
Ifthe batteries have leaked, remove any traces of battery flurd from
the battery compartment wiping thoroughly with a dry cloth. Then
insert new batteries
(2)
Directions for use
®
Operate the Remote Control Unit while pointing it towards the Re-
mote Control Sensor on the Amplifier as shown in the diagram on
the left.
©
The Remote Controi Unit can be used at distances up to about 8 me-
ters in a straight line from the amplifier. This distance will decrease
if there are obstructions blocking the infra-red light transmission or
if the Remote Control Unit is not directed straight at the amplifier
Note on operation
©
Oo not press the operating buttons on the Amptifier and the Remote Control Unit at the same time. This will cause misoperation,
© Operation of the Remote Control Unit will become less effective or erratic if the infrared Remote Control Sensor on the Amplifier is exposed to
strong light or if there are obstructions between the Remote Controi Unit and the sensor.
@
Incase you operate a VCA, TV or other components by remote conto!, do not operate buttons on two different remote control units at the same
time. This wilt cause misoperation.
Remote control section
Full-system Remote Control Unit
12
Remote Control Unit RC-176 supplied with the PMA-925R/725R
© (POWER) sutton
This button can be used to turn on and off the power of the ampli-
fier.
However, the power for the amplifier turned on and off if itis in
the power standby mode and the power cord is plugged in
Bic
get cy har
This button will not function if there is a power failure, if
CoO mal
a
the power cord is not plugged in, or when using an aud.o
KEW
FED
PLAY
timer,
@ = MUTING button
ee
Lol
SI It
-
¥
Pressing this switch will activate the muting condition and no
Seca
Signals will be output to the speakers.
Tare
JaPEy
aux
Other buttons
Other buttons are exclusively for the PMA-925R/725R.
and
function in the same way as the corresponding buttons on the
set.
£0
POND
DENON
REMONE CONTRO, UNIT ACITE
» PLAY
PLAY button
<q PLAY (REY)
PLAY (REV) button
@ stop
STOP button
dq
REW
REWIND button
FF >>
FF button
Reter to the operating
instructions of your
it PAUSE
DENON tape deck
&/B W-DECK
A/B DECK
SELECT burton
D> PLAY
PLAY button
@ STOP
STOP button
Revere ieee
PRESET ¢ buttons
ere
ue
Press this button to move up or down among the preset
Forward Track
Station numbers.
Search button
Refer to the
operating
instructions
'of your DENON
CO player
PAUSE button
RANDON
DISC SKIP
WW PAUSE
«
CAUTION:
©
Only the MUTE/STANDBY LED @ lights when in the power stand-by mode.
13
a
PO
I
I
Fe
el
es
wuseZ/Uuseec-
Advertisement
