Yamaha DX9 Operating Manual page 13

EDIT MODE
• EDIT MODE .... Creating Voices
Th e EDIT mode can be used to edit pre-programmed
voices or to create entirely new voices. Press the IE D IT
I
COMPARE I function key to enter the EDIT mode.
Edit Mode Parameter
LFO
4 WAVE SPEED DELAY
14
/s
11
7
IC
MODE
SAVE /VERIFY LOAD
PORTA MENTO
CASSETTE
KEYBOARD SCALING
DETUNE/
SYNC RATE LEVEL RATE LEVEL
114
1115 1 1 16
11
17
IE
EG BIA S RANGE PITCH AMPLITUDE EG BIAS
BREATH CONTROL
Setting and modifying parameters is carried out using the
DATA ENTRY contro ls just as in the FUNCTIO N mode.
A small dot will appear next to the voice number in the
display if any data is modified . Th e original voice can be
recalled at any time while editing by pressing the
I EDIT /COM PARE
I
key again. The voice number will
flash indicating that you are heari ng the original voice.
T o continue editing press the I EDIT /COM PARE
I
button
again.
Now for an exp lan ation of the DX9's functions and opera-
tion.
• The indicators display for EDIT mode
The number of the al- Display the current
gorithm which is being state of the operators
. used for that particui:Lr from OP1 through OP4
Voice preset voice begining at the left
number
~
RLG 1 1111 OP 1
~
F CORPSE= 1.00
The dot will appear
when any data has
been modified .
Displays each
parameter
• OPERATOR ON-OFF / EG COPY
OPERATOR ON-OFF / EG COPY
The operator selected
will be displa'{1!d only
for the parameters that
can modified
In the ED IT mode these keys permit turning any of the
operators on or off, and copying the EG data of any
operator to any other operator (EG COPY).
<
12>
OPERATOR ON-OFF:
Pressing keys
W
corresponding operator
"0" in the appropriate
through
m
will result in the
being turned OFF, indicated by a
location on the display panel (the
group of four 1 's and/or O's corresponds to operators 1
through 4). Press the key again to turn the operato r back
on-indicated by a "1" on the display.
1 : Signifies that the operator is activated
\
0 : Signifies that the
/ operator is disabled
~
~LG 4 1100
OP2
R~TE SC~LING
=
0
EG COPY :
• No sound will be produced
if the carrier operators
have all been disabled .
Thi s function co pys the EG data from one operator to
another. While holding the selector
I
STORE
I
key, press
the number of the operator from w hi ch you want to
co py EG data .
While pressing
STORE
L~koy
EG COPY
The display panel when the
Store key has been pressed.
EG COPV
fr·or·l
OP2
to
OF'?
press the key for the operator
number that you wish to copy.
fr-ol"l
OP2
to
OP 1
This signifies that the
EG data of 0 P2 are
being copied to OP1 .
• ALGORITHM/ FEEDBACK
Pressing this key alternately sw itches to A LGORITHM
and FEEDBAC K.
ALGORITHM
/ FEEDBACK
/s
ALGORITHM:
Thi s key permits se lection of one of the 8 algorithms.
Press the DATA ENTRY
[ill
key to increment (advance)
the number of the se lected algorithm, and t he
[J]
key
to decrement the algorithm number. Th e slide co ntrol
can be used for lager variations.
This value will change.
/_
r::~:-:-L=-6 -1. ----=-1-=-H-=-cJ
(=-·1 - - - - - - ,
RLGORITHM SELECT