Table of Contents
Advertisement
3M™ Aura™ Particulate Respirators 9300+ Series
Storage and Transportation
3M™ Aura™ Particulate Respirators 9300+ Series have a
shelf life of 5 years from date of manufacture. End of shelf life
is marked on the product packaging and upon the product.
Before initial use, always check that the product is within the
stated shelf life (use by date).
Product should be stored in clean, dry conditions within
the temperature range: – 20°C to + 25°C with a maximum
relative humidity of <80%. When storing or transporting the
respirator, remove bend in noseclip, align top and bottom
panels together before pushing the top panel flat. Store
respirator in original packaging provided.
Warnings and Limitations
Always be sure that the complete product is:
•
Suitable for the application;
•
Fitted correctly;
•
Worn during all periods of exposure;
•
Replaced when necessary.
•
Proper selection, training, use and appropriate
maintenance are essential in order for the product to help
protect the wearer from certain airborne contaminants.
•
Failure to follow all instructions on the use of these
respiratory protection products and/or failure to
properly wear the complete product during all periods
of exposure may adversely affect the wearer's health,
lead to severe or life threatening illness or permanent
disability.
•
For suitability and proper use follow local regulations and
refer to all information supplied. For more information
contact a safety professional/3M representative.
•
Before use, the wearer must be trained in use of the
complete product in accordance with applicable Health
and Safety standards/guidance.
•
These products do not contain components made from
natural rubber latex.
•
These product do not protect against gases/vapours
such as glutaraldehyde.
•
Do not use in atmospheres containing less than 19.5%
oxygen. (3M definition. Individual countries may apply
their own limits on oxygen deficiency. Seek advice if in
doubt).
•
Do not use for respiratory protection against atmospheric
contaminants/concentrations which are unknown or
immediately dangerous to life and health (IDLH).
•
Do not use with beards or other facial hair that may
inhibit contact between the face and the product thus
preventing a good seal.
•
Leave the contaminated area immediately if:
a. Breathing becomes difficult.
b. Dizziness or other distress occurs.
c. The respirator becomes damaged
d. You taste or smell contaminants, or an irritation occurs
•
Discard and replace the respirator if it becomes
contaminated with blood or other infectious material,
damaged, breathing resistance becomes excessive or at
the end of a shift.
•
Do not alter, modify, clean or repair this respirator.
•
In case of intended use in explosive atmospheres,
contact 3M.
•
Before initial use, always check that the product is within
the stated shelf life.
Fitting Instructions
Before fitting device, ensure hands are clean. All respirator
components should be inspected for damage prior to each
use.
1.
With reverse side up, separate top and bottom panels to
form a cup shape. Bend slighty at centre of the noseclip.
2.
Ensure both panels are fully unfolded.
3.
Cup respirator in one hand with open side towards face.
Take both straps in other hand. Hold respirator under
chin, with nosepiece up, and pull straps over head.
4.
Locate the upper strap across the crown of the head
and the lower strap below the ears. Straps must not be
twisted. Adjust top and bottom panels for a comfortable
fit, ensuring panels are not folded in.
5.
Using both hands, mould nose clip to the shape of the
lower part of the nose to ensure a close fit and good seal.
Pinching the nose clip using only one hand may result in
less effective respirator performance.
6.
The seal of the respirator on the face should be fit-
checked before entering the workplace.
Seal Check
1.
Cover the front of the respirator with both hands being
careful not to disturb the fit of the respirator.
2.
(a) UNVALVED respirator - EXHALE sharply;
(b) VALVED respirator - INHALE sharply;
3.
If air leaks around the nose, re-adjust the nose clip to
eliminate leakage. Repeat the above seal check.
4.
If air leaks at the respirator edges, work the straps back
along the sides of the head to eliminate leakage. Repeat
the above seal check.
If you CANNOT achieve a proper seal DO NOT enter the
hazardous area. See your supervisor.
Users should be fit tested in accordance with national
requirements.
For information regarding fit testing procedures, please
contact 3M.
Advertisement
Table of Contents
