General Safety Instructions For Power Tools - Craftsman 113.225909 Owner's Manual

FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER
If within one year from the date of purchase th s Craftsman Belt and Disc Sander fails due to a defect in
material or workmanship, Sears will repair it, free of charge.
WARRANTY sERVICE IS AVAILABLE BY S MPLY CONTACTING THE NEAREST SEARS STORE
OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
SEARS. ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684
general safety instructions power tools
1. KNOW YOUR POWER TOOL
mask if cutting operation is dustv, and ear protectors
Read and understand the owner's manual and labels (plugs or muffs) during extended periods of operation.
affixed to the tool. Learn its application and limitations as
well as the specific potential hazards peculiar to this tool.
13. SECU RE WORK
2. GROUND ALL TOOLS
Th_s foot Is equIPbe(1 with an approved 3.conductor
cord and a 3-prong grounamg type plug tp fit the proper
groundmg type receptacle Th_ _reen conductor n the
cord _s tha grounding wire. Never connect the green w_re
_o a hve termmal.
3. KEEP GUARDS IN PLACE
- m working order, and in proper aolustment and align
ment
4. REMOVE ADJUSTING KEYS AND WRENCHES
Form habit of ¢heckmg to see tnat keys ana adlustmg
wrenches are removed from tool before turning _t pn
5. KEEP WORK AREACLEAN
C_uttereo areas and benches mwte acc_dems FtOol
must not be Slippery due tO wax or SaWdUSt
6. AVOID DANGEROUS ENVIRONMENT
Use clamps or a v_se to hold WOrK When Dractlcal It s
safer than uslng your 13and. frees both hands to operate
tool.
14. DON'T OVERREACH
Keep ProPer foottng and balance at all bmes
15. MAINTAIN TOOLS WITH CARE
Kee_) tools snaro and clean for best and safest perform
ance. Follow nstruct_ons for ubrlcat_ng ano changing
accessor les.
16. DISCONNECT TOOLS
before servicing, when changing accessories SUCh as
blades. P_ts. cutters etc
17. AVOID ACCIDENTAL STARTING
Make sure swdch s m "OFF" position before pluggmg
Ln
18. USE RECOMMENDED ACCESSORIES
Don't LISP Dower tOOlS in damp or wet locations or ex
Consult tbeowner's manua for recommended accessories.
(_se them to raln, Keep work area well hghted Provlde
d(lequate surrounding work space Follow the nslrucPons that accompany the accessories.
7. KEEP CHILDREN AWAY
All visitors should be keot a safed_stance from work area
8. MAKE WORKSHOP CHILD-PROOF
w_tn {_adlpcks rnastel swltche_ or r)V remownq starter
I<eVS
The use of mproDer accessories may cause hazards.
19. NEVER STAND ON TOOL
Serious ]nlury could OCCUI _f the tool _s tipper or tf the
cuttmg tool _s accidentally contacteP
Do not store materials 3bove or near the tool such mat
it s necessar, to stand on the tool to reach them
9. DON'T FORCE TOOL 20.
It wdl do the IOb bt, tter ana safer at the rate to{ which
• was des_qneo
10. USE RIGHT TOOL
_OCt't foFce too ol dttaci_mPnt to (30 a 1o13 r'[ was not
ties gnea for
11. WEAR PROPER APPAREL
Do not weal loose cIothlnh gloves, rleckttes or _ewelrv
brags. _.,rlstwatcnesl to get caugn[ in movlng parts
NONSLIP footwear s iecommended Weal protective
21.
nalr covering to contain long halt. Roll long Sleeves
above the elbow
CHECK DAMAGED PARTS
Before furmer use of the tool a guard or other _)art thai
_s Clamaged should be carefully checked to ensure that LI
will operate properly and perform its intended
function
Check for alignment of mPvmg Darts bJndmg of mowng
baits, breakage of _arts, mountmg, and any other con
dd_ons that may affect ts operation. A guaro Ol othe_
oa_I that is damage(] should De properly repaired Ol
replaced
DIRECTION OF FEED
Feed work mto a blade or cutter aga nst the ChrPCtion Of
rotation of the blade or cutter only
12. USE SAFETY GOGGLES (Head Protection) 22. NEVER LEAVE TOOL RUNN NG
Wear safety goggles (must comply with ANSI Z87,1) at all UN ATTENDED
times. Everyday eyeglasses only have impact resistant Turn power off _)on't leave too_ unt_l t comps _o a
lenses, mey are NOT safety glasses. Also use face or dust coml)lete stop