Advertisement
Quick Links
INSTALLATION, CARE & USE MANUAL
SOFT SIDES
EZWS-EDFPBM117K
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an "electrolysis" effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain fittings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building's plumbing circuits.
EDFPBM117WS
Fountains with FLEXI-GUARD
™
and EZH
2
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
EDFPBM117WS-F
O
Bottle Filler
®
LZWS-EDFPBM117K
Page 1
™
0000001029 (Rev. E - 06/16)
Advertisement
Related Manuals for Elkay SOFT SIDES EDFPBM117WS
Summary of Contents for Elkay SOFT SIDES EDFPBM117WS
- Page 1 EDFPBM117WS EDFPBM117WS-F INSTALLATION, CARE & USE MANUAL SOFT SIDES Fountains with FLEXI-GUARD ™ ™ and EZH Bottle Filler ® EZWS-EDFPBM117K LZWS-EDFPBM117K INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
- Page 2 EDFPBM117WS EDFPBM117WS-F Fig. 1 0000001029 (Rev. E - 06/16) Page 2...
-
Page 3: Required Tools And Materials
EDFPBM117WS EDFPBM117WS-F TO BUBBLER TO BUBBLER REQUIRED TOOLS AND MATERIALS These tables show special tools and/or additional materials (not provided) which are necessary to complete installation of these units: Special Tools Description Quantity Item NONE Additional Materials Not Included Quantity Item Description TO BOTTLE... - Page 4 EDFPBM117WS EDFPBM117WS-F 27, 28, 29, 30, 31 8. Install reset switch for bottle filler (Fig 5). Connect the switch wire to the extension wire on the back of the bottle filler. Wrap up the excess cord. 9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap. Trap on the bottle filler side must be 1-1/2”...
- Page 5 EDFPBM117WS EDFPBM117WS-F Basin Locknut FLEXI-GUARD BUBBLER DETAIL ® NOTE: When installing replacement bubbler and pedestal, tighten locknut only to hold parts snug in position. Do Not overtighten. Figure 6 - Bubbler Details 3/8” Water Inlet WATERSENTRY PLUS FILTER PARTS LIST ®...
- Page 6 EDFPBM117WS EDFPBM117WS-F See Fig. 6 See Fig. 6 Figure 8 - Fountain Body Assembly Figure 9 - Push Button Assembly 0000001029 (Rev. E - 06/16) Page 6...
- Page 7 EDFPBM117WS EDFPBM117WS-F BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE Continued from below: 1) To verify the software program of the control board the unit will 2) When the display changes to “SETTINGS”, depress the button again. need to be shut down and restarted.
- Page 8 EDFPBM117WS EDFPBM117WS-F MAIN PANEL DRAIN MOUNTING FILTER (OPTIONAL) LOCATION FRAME MOUNTING FRAME Fig. 10 0000001029 (Rev. E - 06/16) Page 8...
-
Page 9: Parts List
Note: Screw the locknut hand tight to seal Figure 12 REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 Page 9 0000001029 (Rev. E - 06/16)