Bosch Professional GOP 14,4 Original Instructions Manual page 17

OBJ_BUCH-1808-001.book Page 16 Friday, May 31, 2013 9:29 AM
16 | English
Removing the battery
The battery 5 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 3 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 5, press the battery unlocking button 3
and pull the battery out of the power tool toward the rear. Do
not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
6 indicate the charge condition of the battery 5. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 7 to indicate the charge condition. This is also
possible when the battery 5 is removed.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 7, then the bat-
tery is defective and must be replaced.
Changing the Tool
 Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessoriy can lead to injuries.
Selecting the Application Tool/Accessory
Accessory
HCS wood seg-
ment saw blade*
BIM segment saw
blade*
HCS plunge cut
saw blades,
wood*
BIM plunge cut
saw blades,
metal*
BIM plunge cut
saw blade, wood
and metal*
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
2 609 140 973 | (31.5.13)
Capacity
2/3
1/3
<1/3
Reserve
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/
accessory.
For this, open the SDS lever 8 to the stop (not further) and
remove the application tool.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 11) in such a manner on the tool holder 9 that
the offset faces downward (see illustration on the graphics
page; marking on the application tool/accessory is readable
from above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
Material
the tool holder 9. 12 different positions are possible, each
offset by 30°.
Wooden materials,
plastic
Close SDS lever 8 so that it faces against the housing of the
power tool.
Wooden materials,
 Check the tight seating of the application tool/acces-
plastic, non-ferrous
metals
sory. Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
Wooden materials,
hazard.
plastic, gypsum and
other soft materials
Mounting/Replacing a Sanding Sheet on the Sanding Plate
Metal (e.g. unhard-
The sanding plate 12 is fitted with Velcro backing for quick
ened nails, screws,
and easy fastening of sanding sheets with Velcro adhesion.
smaller profiles),
Before attaching the sanding sheet 13, free the Velcro back-
non-ferrous metals
ing of the sanding plate 12 from any debris by tapping against
Wood, metal, non-
it in order to enable optimum adhesion.
ferrous metals
Position the sanding sheet 13 flush alongside one edge of the
sanding plate 12, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Accessory Material
HM-Riff segment Grouting joints, soft
saw blade* wall tiles, glass-fibre
reinforces plastic
and other abrasive
HM-Riff delta
materials
plate*
Scraper, rigid* Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for Depends on sanding
sanding, series sheet
Delta 93 mm*
Bosch Power Tools