Related Manuals for TRENDnet TV-IP201P
Summary of Contents for TRENDnet TV-IP201P
- Page 1 Quick Installation Guide TV-IP201P...
-
Page 2: Table Of Contents
Table of Contents Table of Contents English ... 1. Before You Start 2. Hardware Installation ... 3. Configure the Internet Camera ... 4. Power over Ethernet (PoE) Installation ... Troubleshooting ... Version 06.08.2007... -
Page 3: English
Power + Data (PoE) Power over Ethernet Power Jack 16-Port 10/100Mbps Fast Ethernet Switch (TE100-S16) Power Data Package Contents TV-IP201P Quick Installation Guide Utility CD-ROM Metal Stand AC Power Adapter (5V, 2.5A) PoE Internet Camera Server with Audio (TV-IP201P) Internet Router/Modem... -
Page 4: Hardware Installation
2. Hardware Installation 1. Mount the Internet Camera to the metal stand. 2. Connect a RJ-45 network cable from a Switch/Router to the LAN port of the Internet Camera. 3. Connect the AC Power Adapter to the Internet Camera and then to a power outlet. -
Page 5: Configure The Internet Camera
3. Configure the Internet Camera Note: Since the Internet Camera's default IP address is 192.168.0.30, make sure no other network devices are assigned an IP address of 192.168.0.30 1. Insert the Utility CD-ROM into your CD-ROM drive and then click Setup Wizard. - Page 6 5. Click Yes. 6. Enter the Admin ID and Password, and then click OK. By default: User Name: admin Password: admin 7. If your network is on a different subnet, an IP address in your network's subnet will automatically be generated. If this IP address is not used by another device in your network, click OK.
- Page 7 8. Enter the Admin ID and Password, and then click OK. By default: Admin ID: admin Password: admin If you like to change the Admin ID and password, click Change, enter the New ID and the New Password and confirm the New ID and News Password.
- Page 8 Admin ID: admin Password: admin Your installation is now complete. Note: For detailed information regarding the TV-IP201P configuration and advanced settings, please refer to the Troubleshooting section, User’s Guide on the Utility CD-ROM, or TRENDnet’s website at http://www.trendnet.com. To ensure the highest level of customer service and support, please take a moment to...
-
Page 9: Power Over Ethernet (Poe) Installation
4. Power over Ethernet (PoE) Installation Using the TV-IP201P with a PoE switch 1. Connect a RJ-45 cable from the Power over Ethernet Switch to the LAN port of the Internet Camera Server. 2. Verify that the LEDs are on. - Page 10 Using the TV-IP201P with an Injector (TPE-101I) 1. Connect the Power Cord to the Injector. Then connect the Power Cord to an outlet. 2. Connect a CAT-5 cable from a switch to the TPE-101I's Data In port. 3. Connect a CAT-5 cable from the...
-
Page 11: Troubleshooting
First, make sure that you are using a browser that supports Active X or Java. Second, make sure that Active X or Java is installed and enabled. The TV-IP201P does not power on when I plug the device into a Power over Ethernet switch or splitter. What should I do? First, verify that the PoE device supports IEEE 802.3af protocol. - Page 12 Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation.
- Page 13 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 Copyright ©2007. All Rights Reserved. TRENDnet.