Maintenance And Storage - IVT AC-24L Instruction Manual

Adjusting the pressure
Pressure reducer (21)
The pressure reducer (21) allows adjusting outlet air
pressure in the connection nipple (3) of the controlled
pressure pipeline, depending on consumption.
Set required working pressure, - pressure value should
be read on pressure gauge (5):
∙ to decrease pressure: turn the pressure reducer
handle (4) counterclockwise.
∙
to increase pressure: turn the pressure reducer
handle (4) clockwise.
[F3]
NOTE: the machine design provides the adjustment of
compressed air output pressure only in the nipple (3) of
the controlled pressure pipeline. Output pressure in the
pipe connector (7) is equal to receiver (2) pressure value;
pressure value should be read on pressure gauge (8).

MAINTENANCE AND STORAGE

Before any work on the device itself,
pull the mains plug.
∙ Always keep the tool and the ventilation slots (if present)
cleaned. Regular cleaning and maintenance of the appliance
will ensure efficiency and prolong the life of your tool.
∙ If the tool should fail despite the rigorous
manufacturing and testing procedures, the repair should
be carried out by an authorized IVT customer service.
∙ Keep all nuts, bolts, and screws tight, to be sure the
tool is in safe working condition.
∙ Replace worn or damaged parts for safety.
∙
Use only original spare parts. Parts not produced
by manufacturer may cause poor fit and possible injury.
∙ Store the tool in a dry room out of reach of kids and
away from any flammable material.
∙ Never wet the device or spray water on it!
CAUTION!
procedure, the machine should be
obligatory disconnected, power cable
should be taken out from the socket and
receiver (2) pressure should be released
(pull the ring of safety valve (11)).
Cleaning the machine
Exterior surfaces of the device should be cleaned after
operation with a soft brush and cloth.
Do not use caustic substances or solvents for cleaning
the machine.
Prior to starting any
Changing the oil
Regularly check the condition of the oil (every 6 months).
It is necessary to change the oil after the first 30 hours
of machine operation.
[F4]
1. Place the machine on a flat surface.
2. Place container for draining waste oil under the
drain hole.
3. Screw out the oil drain plug (27) and wait until
waste oil stops leaking from the drain hole.
4. Screw in the oil drain plug (27), fill up the oil tank
with new oil.
ATTENTION! Dispose of the waste oil
environmentally safe by taking it to a
proper collecting point!
Air filter (17) maintenance
Regularly examine filtering element (23) of the air
filter (17) (its clogging depends on various ambient
conditions). Clean (or replace) the air filter as often as
required, but no rarer than after 100 operating hours. A
clogged air filter reduces compressor's efficiency and
leads to the wearing of the compressor.
ATTENTION! Do not twist the filtering
element (23), otherwise it may be
damaged.
1. Place the machine on the flat surface.
2. Unscrew the fixing bolt (if present).
3. Grip with fingers the cover (22) and remove it.
4. Take out the filtering element (23).
5. Cleanse the filtering element (23) in alcohol or solvent.
6. Remove residual alcohol or solvent properly.
7. Set the filtering element (23) into the cover (22).
8. Place the cover (22) into its location and press it until
plastic pawls are latched. Or tighten the fixing bolt (if present).
[F5]
Condensate draining
Periodically, as well as after stopping operating (if
operation lasts more than one hour) drain condensate
from the receiver (2). This prevents from forming
corrosion inside the receiver (2).
1. Place the machine on a flat surface.
2. Place a container for condensate draining under
the machine, under the slide valve (19).
3. Unscrew and remove the slide valve (19) and wait
until condensate is completely drained and water drops
stop falling from the slide valve (19).
4. Tighten the slide valve (19).
[F6]
11
Instruction manual
EN