Related Manuals for Kohler K-12205-H Series
Summary of Contents for Kohler K-12205-H Series
- Page 1 Freewill Barrier Free Multi-Piece Bath Whirlpools: K-12205-H* K-12206-H* E1999 Kohler Co. 116014-2-...
-
Page 2: Important Safety Instructions
Use this unit only for its intended use as denoted in this above the normal body temperature of 98.6 F. The manual. DO NOT use attachments not recommended symptoms of hyperthermia include an increase in the by the Kohler Co. internal body temperature,... -
Page 3: Table Of Contents
Follow the sections that pertain Kohler Co. reserves the right to make changes in to your particular installation. This will help you avoid product characteristics, packaging, or availability at any costly mistakes. -
Page 4: Roughing-In: K-12205-H*, K-12206-H
60” side entrance. 36” Ë Ë Ë Ë 4” 60” Represents clear floor space for 48” 19” 23-1/2” 4” x 60” side entrance. 48” 2-7/8” 3/4” C L SPOUT 60” 3” 1-1/2” O. D. Kohler Co., Kohler, WI 116014-2-... -
Page 5: Product Notices
WARNING: Risk of electrical shock. Disconnect performance and safe operation of the whirlpool. power before servicing. Kohler Co. shall not be liable under its warranty or WARNING: Risk of injury or property damage. otherwise for personal injury or damage caused by Please read all instructions thoroughly before any such unauthorized modification. -
Page 6: Installation Requirements
Remove the old wall material, and remove any old floor of the framing. covering from the area. Remove any old plumbing that does not conform to roughing-in requirements. Kohler Co., Kohler, WI 116014-2-... -
Page 7: Site Requirements
To ensure ADA compliance, position the module exactly as shown in the roughing-in diagram on Page 4. If the user will have care giver assistance, we recommend that you employ a front entrance. Kohler Co., Kohler, WI 116014-2-... -
Page 8: Plumbing Access Considerations
When fire wall is specified, it should be in place before you install the unit. If unit is to be installed adjacent to a vertical duct or chase, fire-rated gypsum drywall should surround the unit. Kohler Co., Kohler, WI 116014-2-... -
Page 9: Stud Pocket Preparation
Carefully move the sections to the installation area, Block setting them again on a prepared, level surface, (this is a two-man job). Washer It is helpful to have all seam surfaces accessible for the following steps. Kohler Co., Kohler, WI 116014-2-... -
Page 10: Join And Seal Module Sections
Clear silicone sealant is a superior product to Masking Tape ensure against leaks. Use of acrylic or other caulks is not recommended. Sealant may set up quickly. Proceed to the next steps immediately. Bottom Section Kohler Co., Kohler, WI 116014-2-... -
Page 11: Bolt Tightening Sequence
B. PROTECT WHIRLPOOL UNIT Position a drop cloth or similar material in the bottom of the unit. Be careful not to scratch the surface of the product. Kohler Co., Kohler, WI 116014-2-... -
Page 12: Install Whirlpool
Attach the unit to the 2x2 brace and toe plate previously installed around the recess rough opening. Use #6 large-head galvanized nails or #8 x 1” sheet metal screws across the top and bottom, and up both sides. Kohler Co., Kohler, WI 116014-2-... -
Page 13: Pump Banding Strap Cut
B. PUMP BANDING STRAP CUT Shipping Bracket (leave attached NOTICE: This step is necessary to make your to bath) Kohler whirlpool operate more quietly. Pump Banding Straps Use tin snips to cut the two banding straps. These banding straps secure pump whirlpool-mounted shipping bracket. -
Page 14: Electrical Connections
Wire grounding adapter. Bonding (Earthing) Lug* Your Kohler whirlpool bath is equipped with a cord and plug. All wiring of the pump and control has been completed at the factory. A licensed electrician must Pump install a GFCI-protected, 120 V, 20 A, grounded outlet. -
Page 15: Complete Finish Wall
Grab bars can also be installed directly to the module, providing the proper fastening device is selected to securely attach the bar to the unit. Manufacturer’s suggestions concerning grab bar installation must be carefully followed. Kohler Co., Kohler, WI 116014-2-... -
Page 16: Install Shower Rod
Position the shower rod so the shower curtain hangs inside the bath. E. SHOWER DOOR INSTALLATION Shower doors for this unit are available from the Kohler Co. Contact your dealer for more information on shower door availability and installation. When shower doors are to be installed on this bath... -
Page 17: Operating Sequence
Insert the Flexjet into the housing, and lightly push and rotate the Flexjet until it snaps into position. Do not force the Flexjet. O-Ring (Must NOTE: When installed correctly, the Flexjet should turn Be Lubricated) smoothly both clockwise and counterclockwise. Kohler Co., Kohler, WI 116014-2-... -
Page 18: Troubleshoot Whirlpool System
B. TROUBLESHOOT WHIRLPOOL SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1. - Page 19 Kohler Co., Kohler, WI 116014-2-...
- Page 20 116014-2- Kohler Co., Kohler, WI...