en Descaling
Use the function selector to set the cleaning
1.
functions .
a The
symbol and the cleaning functions appear in
the display. The first cleaning function is highlighted.
Press the or button repeatedly until the
2.
symbol is highlighted.
Use the temperature selector to set the cleaning set-
3.
ting.
Cleaning set-
Cleaning
ting
level
1
Low
2
Medium
3
High
Select a higher cleaning setting if the cooking com-
partment is particularly dirty or has not been
cleaned for a while.
The duration cannot be changed.
a After a few seconds, the cleaning function starts and
the duration counts down.
18 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
The frequency with which the appliance must be de-
scaled depends on the hardness of the water used.
The
symbol reminds you to run the descaling pro-
gramme.
There are four steps in the descaling programme. For
hygiene reasons, the descaling programme must be
run through completely so that the appliance can be
ready for operation again. Descaling takes around 90–
110 minutes in total:
Display
Step
First step: Descaling
Approx. 65 min
Second step: Rinse cycle
Approx. 9 min
Third step: Rinse cycle
Approx. 9 min
Fourth step: Rinse cycle
Approx. 9 min
18.1 First step ( )
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
Only use the liquid descaler recommended by us
▶
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
Remove descaling solution immediately with water.
▶
Note: Do not pour more than 150 ml of liquid into the
water tank throughout the descaling process.
26
Duration in hours
Approx. 1:15
Approx. 1:30
Approx. 2:00
a For your safety, the appliance door locks once a
certain temperature is reached in the cooking com-
partment. appears on the display.
a When the cleaning function ends, a signal tone
sounds and the duration is at zero on the display.
Switch off the appliance.
4.
When the appliance has cooled down sufficiently,
the appliance door is unlocked and goes out.
Prepare the appliance for use. → Page 26
5.
17.3 Preparing the appliance for use
following the cleaning function
Allow the appliance to cool down.
1.
Wipe off any ash that has been left behind in the
2.
cooking compartment and around the appliance
door with a damp cloth.
Remove white residues with lemon juice.
3.
Note: White residues on the enamel surfaces may
be caused by heavy soiling. These food residues
are harmless. The deposits do not compromise the
functionality of the appliance.
Attach the shelf supports.
4.
→ "Shelf supports", Page 27
Mixing a descaling solution:
1.
– 50 ml liquid descaler
– 100 ml water
Pour the descaling solution into the water tank and
2.
insert the water tank.
Use the function selector to set the cleaning
3.
functions .
a The
symbol and the cleaning functions appear in
the display. The first cleaning function is highlighted.
4.
Press the or button repeatedly until the
symbol is highlighted.
Turn the temperature selector.
5.
appears in the display. Descaling starts after a
a
few seconds.
a At the end of the descaling programme, ap-
pears in the display.
Remove the water tank and clean thoroughly with
6.
water.
18.2 Second step ( )
Fill the water tank with 150 ml water and insert it.
1.
a At the end of the rinse cycle, appears in the dis-
play.
Remove the water tank and clean thoroughly with
2.
water.
18.3 Third step ( )
Fill the water tank with 150 ml water and insert it.
1.
a At the end of the rinse cycle, appears in the dis-
play.
2.
Remove the water tank and clean thoroughly with
water.