Advertisement
3.2.2 Assembly/Disassembly of cabinet parts and electrical parts
Disassembly procedure
STEP
Fig.
PART NAME
No.
No.
[1]
BOTTOM CASE ASSY
3-2-1
[2]
LOWER CASE ASSY
3-2-2
[3]
UPPER ASSY
3-2-3
[4]
TOP COVER
3-2-4
REAR COVER ASSY
[5]
(Inc.REAR BOARD ASSY
3-2-5
/ZOOM UNIT)
[6]
ZOOM UNIT
3-2-6
[7]
REAR BOARD ASSY
3-2-7
[8]
FRONT ASSY
3-2-8
[9]
MIC
3-2-9
[10]
MAIN BOARD ASSY
3-2-10
[11]
LOWER LINK
3-2-11
[12]
OP BLOCK ASSY
3-2-12
[13]
COVER UPPER
3-2-13
[14]
OPE BOARD ASSY
3-2-14
[15]
MONITOR ASSY
3-2-15
[16]
SPEAKER
3-2-16
NOTE1:
When removing, open the COVER(SD).
NOTE2a:
Pull out the GRIP BELT from the HOOK and leave it re-
leased before removing the HDD COVER ASSY.
NOTE2b:
When attaching the TOP COVER ASSY, insert FRONT
COVER in the space between LOWER CASE and
BKT(G.BELT) first.
NOTE2c:
When removing, remove the COVER JACK(FR).
NOTE3:
When attaching, be careful with the FPC.
NOTE5a:
During the procedure, be careful in handling the FPC.
NOTE5b:
When attaching, be careful with the FPC.
NOTE6:
The ZOOM UNIT is attached with the 3 screws (15-17). Do
not remove it if not needed.
NOTE8:
When attaching, be careful with the WIRE (MIC) and the wir-
ing.
NOTE9:
When attaching, be careful not to break the parts.
NOTE12:
Refer to 3.2.3 Assembly/Disassembly of [12] OP BLOCK
ASSY/CCD BOARD ASSY of OP BLOCK ASSY.
NOTE13:
During the procedure, be careful not to break the parts.
NOTE14a:
During the procedure, be careful with the FPC.
NOTE14b:
During the procedure, be careful with the WIRE (SPK) and the wir-
ing.
POINT
NOTE
3(S1),L1a,2(L1b)
NOTE1
5(S2a),S2b,L2
NOTE2a,b,c
CN3,2(S3),L3a,b,c
NOTE3
L4a,b
-
CN5a,b,3(S5),L5
NOTE5a,b
3(S6)
NOTE6
L7
-
S8,L8a,b,CN8
NOTE8
S9,L9a,b,PLATE(MIC)
NOTE9
CN10a,b,2(S10),L10a,b
-
S11,2(L11)
-
3(S12),FRAME ASSY
NOTE12
2(S13),L13
NOTE13
CN14a,b,2(S14),2(L14a),L14b
NOTE14a,b,c,d,e
2(S15),L15
NOTE15
S16,L16a,b,HOOK,BKT(SPK)
-
NOTE14c:
When removing, be careful in handling the KNOB (SLIDE) as they
may come off.
NOTE14d:
When attaching, make sure that the LEVER of the SW(S407) inter-
locks with the KNOB (SLIDE).
After the attachment, check the normal operation of the
MODE SWITCH.
NOTE14e:
When attaching, open the MONITOR ASSY. If the MONITOR
ASSY is left CLclose during the procedure, the SW (S401) may be
damaged.
NOTE15:
Refer to 3.2.4 Disassembly of [15] MONITOR ASSY of
MONITOR ASSY.
Destination of connectors
CN.
CONNECTOR
No.
CN3
MAIN
CN101
CN5a MAIN
CN104
CN5b MAIN
CN103
CN8
MAIN
CN107
CN10a MAIN
CN105
CN10b MAIN
CN106
CN14a OPE
CN403
CN14b OPE
CN402
PIN
No.
OPE
CN401
30
ZOOM UNIT
-
12
REAR
CN601
30
MIC
-
4
CCD
CN5001
20
OP BLOCK ASSY
-
25
SPEAKER
-
2
MONITOR
CN7601 22/23
(No.YF259<Rev.001>)1-7
Advertisement
