Table of Contents
Advertisement
6. Preparation begins. An image of the selected drink appears
on the display, together with a progress bar which gradual-
ly fills as preparation progresses.
Important! Making LONG coffee
Halfway through preparation, the message "ADD PRE-GROUND
COFFEE, MAXIMUM ONE MEASURE" is displayed. Add one level
measure of pre-ground coffee and press "
Please note!
If "Energy Saving" mode is active, you may have to wait a few
seconds before the first coffee is delivered.
10. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES
Please note!
•
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid (D2) and hot water con-
nection nozzle (A9) as described in sections "10.4 Cleaning
the milk container after every use", "16.10 Cleaning the
milk container" and "16.11 Cleaning the hot water/steam
connection nozzle".
10.1 Filling and attaching the milk container
1. Remove the lid (D2) (fig. 14);
2. Fill the milk container (D3) with a sufficient quantity of
milk, not exceeding the MAX level marked on the handle
(fig. 15). Each mark on the side of the container corre-
sponds to about 100 ml of milk;
Please note!
•
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
•
If "Energy Saving" mode is enabled, you may have to wait a
few seconds before the drink is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 16);
4. Place the lid back on the milk container;
5. If present, extract the hot water/steam spout (C6) by press-
ing the release button (C7) (fig. 17);
6. Attach the milk container (D) to the connection nozzle (A9)
(fig. 18) and push as far as it will go. The machine emits a
beep (if the beep function is enabled);
7. Place a sufficiently large cup under the coffee spouts (A8)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 19).
8. Follow the instructions below for each function.
10.2
Turn the froth adjustment dial (D1) to adjust the amount of froth
:
on the milk delivered while making cappuccinos and milk-based
coffees.
Dial
OK" .
position
10.3
1. Fill the milk container (D) and attach it as described above.
2. Select the required drink:
3. A message on the display (B) instructs you to turn the froth
4. After a few seconds, preparation begins automatically and
•
•
•
15
Adjusting the amount of froth
Description
Recommended for...
NO FROTH
HOT MILK (not frothed)
CAFFELATTE
MIN. FROTH
LATTE MACCHIATO / FLAT
WHITE
MAX. FROTH
CAPPUCCINO/ CAPPUCCI-
NO+ / CAPPUCCINO MIX/
ESPRESSO MACCHIATO /HOT
MILK (frothed)
Making cappuccinos and milk-
based coffees automatically
• CAPPUCCINO
• LATTE MACCHIATO
• CAFFELATTE
• LATTE CALDO
• CAPPUCCINO+
• ESPRESSO MACCHIATO
• FLAT WHITE
• CAPPUCCINO MIX
adjustment dial (D1) according to the froth required by the
original recipe. Turn the dial on the milk container lid (D2)
and confirm the selection by pressing "
an image of the selected drink appears on the display, to-
gether with a progress bar which gradually fills as prepara-
tion progresses.
Please note: general indications when preparing all
milk-based drinks
"
ESC": press to interrupt preparation completely and
go back to the homepage.
"
STOP": press to interrupt milk or coffee delivery and
move on to the next delivery to complete the drink.
At the end of delivery, to increase the quantity of coffee in
the cup, press "
EXTRA".
OK".
Advertisement
Table of Contents
Troubleshooting
