Maintenance - Craftsman CMCF600 Instruction Manual

nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start-up. This is
normal and does not indicate a problem.
Lock-On Button (Fig. A)
To lock the switch in the ON position for continuous
operation, depress the trigger switch
lock-on button 9 . The tool will continue to run. To turn the
tool off, from a locked on condition, squeeze and release the
trigger once. Before using the tool (each time), be sure that
the locking button release mechanism is working freely.

CAUTION: Be sure to release the locking mechanism
before removing the battery from the tool. Failure to do
so will cause the tool to start immediately the next time
the battery is installed. Damage or injury could result.
Worklight (Fig. A)
The worklight 10 is activated when the trigger switch
depressed, and will automatically turn off 20 seconds after
the trigger switch is released. If the trigger switch remains
depressed, the worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Screwdriving (Fig. A)
For best results, hold the screwgun with the hand directly in
line with the fastener and press the variable speed trigger
switch with the last one or two fingers of the hand. This
reduces the chance of the screw slipping from the drive
accessory when pressure is applied.
To drive the fastener, place it on the bit, press the variable
speed trigger switch and push the fastener into the
workpiece with a smooth, continuous motion. When the
fastener is seated, the clutch will disengage automatically.
1. Install bit tip in bit holder.
2. Adjust depth locator
3. Check for correct rotation, start screwgun and place
screw on bit.
4. Contact work surface, applying forward pressure to drive
screw until depth locator contacts the work surface.
Screwgun will ratchet automatically, disengaging bit
from screw.
5. This depth sensitive screwgun is suitable for driving
drywall screws.
For this Depth Sensitive Clutch Please
Remember:
• The bit will not turn until pressure is applied to the unit.
Push to engage.
• Trigger switch will not depress unless tool is in either
forward or reverse position.
7 and push up the
1 .

MAINTENANCE


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Nose Cone Maintenance (Fig. A)
If the nose cone
contaminated with drywall dust.
1. Remove nose cone from tool.
2. Rinse thoroughly with warm water while rotating both
screw depth adjustment collar
Never use oil or solvents.
3. Dry the nose cone completely before reattaching to tool.
7 is
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN. Call 1‑888‑331‑4569.
VersaTrack™ (Fig. I)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.

WARNING: To reduce the risk of serious personal
injury, do not use a damaged VersaTrack™ hang hook
or VersaTrack™ Trackwall. A damaged VersaTrack™
hang hook or VersaTrack™ Trackwall will not support
the weight of the tool.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the VersaTrack™ hang
hook is securely tightened.
4 becomes hard to turn it may be
2 and locking collar
English
3 .
9