Table of Contents
Advertisement
Available languages
Available languages
Plunge Cutting
WARNING: Hold saw firmly with both hands for all
cutting operations.
WARNING: Inspect work area for hidden electrical
wiring, gas pipes or water pipes before making blind
or plunge cuts. Failure to do so may result in electrical
shock, fire, explosion, or property damage.
Sanding
WARNING: Fire hazard. When working on metal
surfaces, do not use a vacuum cleaner because sparks
are generated. Wear safety glasses and a dust mask.
Due to the danger of fire, do not use your sander to
sand magnesium surfaces. Do not use for wet sanding.
nOTE: Do not rest fingers on platen during use. Move it in
long sweeping strokes across the surface, letting it do the
work. Light pressure is all that is required for sanding.
Helpful Hints
•
Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
•
Do not start sanding without having the sandpaper
attached to sanding platen.
•
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and fine grit for the
finishing surfaces. If necessary, first make a test run on
scrap material.
•
Excessive force will reduce the working efficiency and
cause motor overload. Replacing the accessory regularly
will maintain optimum working efficiency.
•
Do not allow the sandpaper to wear away, it will damage
the sanding pad.
•
If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for
2–3 minutes to cool the motor. Avoid prolonged usage
at very low speeds. Always keep the blade sharp.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1‑888‑331‑4569.
VersaTrack™ (Fig. K)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: To reduce the risk of serious personal
injury, do not use a damaged VersaTrack™ hang hook
or VersaTrack™ Trackwall. A damaged VersaTrack™
hang hook or VersaTrack™ Trackwall will not support
the weight of the tool.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the VersaTrack™ hang
hook is securely tightened.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
VersaTrack™ Trackwall using the hang hook.
WARNING: The Versatrack™ integral hang hook is not
a belt hook.
WARNING: Ensure that the tool weight does not
exceed the maximum rated weight of 20 lb (9 kg) for
the selected VersaTrack™ hook.
WARNING: When hanging objects on a VersaTrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: When attaching the VersaTrack™ hang
hook, use only the screw that is provided. Be sure to
securely tighten the screw. VersaTrack™ accessories
mount compatible tools securely to the VersaTrack™
Trackwall system.
1. Turn the tool off, remove the battery pack
and accessories.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
the VersaTrack™ Trackwall.
2. Attach the hang hook
a. Place the VersaTrack™ hang hook onto the mounting
location
at the base of the tool.
19
b. Use a screwdriver to secure the hang hook with the
provided screw
12
for this.
11
on the tool.
. Do not use any other screw
English
11
Advertisement
Table of Contents
