Table Of Contents - Trane CVRD Installation Instructions Manual

Table of Contents

General Information
. . . . . . . . . . . . . . . . . . . . . . . 5
About This Manual
Unit Model Number
Other Required Manuals
Required Tools
. . . . . . . . . . . . . . . . . . . . . . . . . 5
Field-Provided Material
Model Number Descriptions
Getting Started
. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Nameplate
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Symbio 800 AdaptiView Display Upgrade Kit
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Running the IPC Bus . . . . . . . . . . . . . . . . . . 9
Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Check the Configuration and Set-Points in the
DynaView Display . . . . . . . . . . . . . . . . . . . 11
Save the DynaView Configuration and Set-
Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remove the Existing Control Panel Door
Install New Control Panel Door and Symbio 800
Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Choosing Display Arm Mounting Location
Alternative mounting location: . . . . . . . . . . 14
Mounting Display Arm
Adjusting the Tracer AdaptiView Display
Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Install Power Supplies and Hardware
Install 1A2 Power Supply-CH530 If Not Already
Present . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Install 1A2 Power Supply - CH531 Prebuilt Pan-
els . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Install Quad Relay Output LLID-CH530 If Using
Chiller Control Sequence 1 . . . . . . . . . . . . 17
Install Communication Cable Between 1A1 and
1A2 Power Supplies . . . . . . . . . . . . . . . . . . 17
Connect Input Power Wiring to 1A2 Power Sup-
ply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Routing New Wire Into and Out of the Control
Panel Enclosure . . . . . . . . . . . . . . . . . . . . . 18
Wiring Connections to the Display and Symbio
800 Controller . . . . . . . . . . . . . . . . . . . . . . . 18
Solid State Oil Heater Relay Installation
Mounting Location . . . . . . . . . . . . . . . . . . . 21
4
. . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . 7
. . . 12
. . . . . . . . . . . . . . . . . . 14
. . . . . 16
. . . 21
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .22
Install Options
LON Option Installation . . . . . . . . . . . . . . . .23
Communication Option . . . . . . . . . . . . . . . .23
Communication Device Mounting . . . . . . . .24
Water Flow Measurement Options . . . . . . .25
Energy Meter Option Installation . . . . . . . . .26
Expansion Module Option . . . . . . . . . . . . . .27
Before Restoring System Power . . . . . . . . .28
Restoring System Power . . . . . . . . . . . . . . .28
Programming
Programming the Symbio 800 AdaptiView
Start-Up
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Wiring Diagrams
. . 13
. . . . . . . . . . . . . . . . . . . . . . . . .23
. . . . . . . . . . . . . . . . . . . . . . . . . . . .29
. . . . . . . . . . . . . . . . . . . . . . . . .33
. .29
SO-SVN037A-EN