Troubleshooting - Metabo BS 1800 L Plus Original Instructions Manual

soft tool shank, retightening may be required after a
short drilling period.
Cleaning: from time to time, hold the machine
vertically with the chuck facing downwards and
turn the sleeve fully in the direction "GRIP, ZU"
and then turn fully in the direction
"AUF, RELEASE". The dust collected falls from
the keyless chuck.
7.8 Unscrewing the chuck
Employ the same procedure when attaching the
chuck, except in reverse order.
7.9 Chuck with quick change system (with
BS 18 L Quick)
To remove: push the interlock ring forward (a),
advance and pull off the chuck forwards (b).
To fit: push the interlock ring forward and move the
chuck as far as the limit stop on the drill spindle.
7.10 Fitting the belt hook (equipment-
specific) / bit depot (equipment-specific)
Fig. J
Fit the belt hook (7) as shown.
Fit the bit depot (6) as shown.

8. Troubleshooting

8.1 The machine's multifunctional
monitoring system
If the machine switches off automatically, the
machine electronics have activated automatic
protection mode. A warning signal sounds
(continuous beeping). The beeping stops after a
maximum of 30 seconds or when the trigger switch
(13) is released.
In spite of this protective function, overloading
is still possible with certain applications and
can result in damage to the machine.
Causes and remedies:
1. Battery pack almost empty
electronics protect the battery pack against
damage through total discharge).
If one LED (10) is flashing, the battery pack is
almost flat. If necessary, press the button (9) and
check the LEDs (10) to see the charge level. If
the battery pack is almost flat, it must be
recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
Note: if the battery pack feels very warm, the
pack will cool more quickly in an "AIR COOLED"
charger.
Note: the machine will cool more quickly if you
operate it at idling speed.
3. Metabo safety shutdown: the machine has
SHUT DOWN by itself. If the speed suddenly
drops (for example, if the machine suddenly
seizes or kickback occurs), the machine
switches off. Switch off the machine at the
trigger switch (13). Switch it on again and
Fig. H
Fig. I
Fig. A, B (The
continue to work as normal. Try to prevent the
machine from seizing.
9. Accessories
Only use original Metabo battery packs and Metabo
accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fitting the angle drilling attachment
For a complete range of accessories, see
www.metabo.com or the catalogue.
10. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Protect the environment, and do not dispose
of power tools and battery packs with house-
hold waste. Observe national regulations on
separated collection and recycling of disused
machines, packaging and accessories.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).
12. Technical Data
Fig. L. We reserve the right to make technical
improvements.
U = Voltage of battery pack
n = No-load speed
0
Tightening torque for screwing:
M = Soft screwing application (wood)
1
M = Hard screwing applications (metal)
3
M = Adjustable torque
4
Max. drill diameter:
D = in steel
1 max
D = in softwood
2 max
D = in masonry
3 max
s = Max. impact rate
m = Weight (with the smallest battery pack)
G = Spindle thread
ENGLISH en
Fig. K.
13