Replacing the filter
For instructions on how to replace the filter, see the section
"Replacing the filter" (page 18).
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the P button to enter the menu;
2. Turn the selection dial (fig. 8) until "Adjust time" is
displayed;
3. Press the
button (fig. 2).
4. Turn the selection dial (fig. 8) to change the hours;
5. Press the
button to confirm;
6. Turn the selection dial (fig. 8) to change the minutes;
7. Press the
button to confirm.
This sets the time. Press the
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note:
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the P button to enter the menu;
2. Turn the selection dial (fig. 8) until "Auto-start" is
displayed;
3. Press the
button. "Enable?" is displayed;
4. Press the
button to confirm;
5. Turn the selection dial to choose the hours;
6. Press the
button to confirm;
7. Turn the selection dial (fig. 8) to change the minutes;
8. Press the
button to confirm;
9. Then press the
Once the time has been confirmed, activation of auto-start is
indicated by the
symbol displayed alongside the time
and under "Auto-start" in the menu.
To disable the function:
1. Select auto-start from the menu;
2. Press the
button. "Disable?" is displayed;
3. Press the
button to confirm.
The
symbol is no longer displayed.
Auto-Off
The time can be changed so that the appliance switches off
after 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the P button to enter the menu;
2. Turn the selection dial (fig. 8) until "Auto-off" is
displayed;
3. Press the
button;
button to exit the menu.
button to exit the menu.
4. Turn the selection dial (fig. 8) until the required operating
time (15 or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the
button to confirm;
6. Then press the
Auto-off is programmed.
Energy saving
Use this function to enable or disable energy saving.
When enabled, the function reduces energy consumption in
compliance with European regulations.
When energy saving mode is active, an asterisk appears under
"Energy saving" in the menu.
To enable or disable energy saving, proceed as follows:
1. Press the P button to enter the menu;
2. Turn the selection dial (fig. 8) until "Energy saving" is
displayed;
3. Press the
"Enable?" if the function has already been disabled);
4. Press the
button to disable energy saving mode;
5. Then press the
When the function is active, if the machine is not used for some
time, "Energy saving" is displayed.
Please note!
•
When in energy saving mode, a few seconds elapse
before the first coffee, cappuccino or milk based coffee is
delivered as the appliance must heat up again.
•
To prepare any drink, press any button to exit energy
saving, then press the button corresponding to the drink
you want to make.
•
If the milk container is inserted, "Energy saving" is not
activated.
Setting the temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
1. Press the P button to enter the menu;
2. Turn the selection dial (fig. 8) until "Set temperature" is
displayed;
3. Press the
button;
4. Turn the selection dial until the required temperature
(●=low; ●●●●=high) is displayed;
5. Press the
button to confirm;
6. Then press the
Setting water hardness
For instructions on setting water hardness, see page 17.
10
button to exit the menu.
button. "Disable?" is displayed (or
button to exit the menu.
button to exit the menu.