Related Manuals for Asus AAEON UPX-EDGE-TGL01
Summary of Contents for Asus AAEON UPX-EDGE-TGL01
- Page 1 UP Xtreme i11 EDGE Maker Board System UPX-EDGE-TGL01 User’s Manual 1 Edition Last Updated: November 4, 2021...
- Page 2 Copyright Notice This document is copyrighted, 2021. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
- Page 3 Acknowledgements All other product names or trademarks are properties of their respective owners. Microsoft Windows and Windows 10 are registered trademarks of Microsoft ⚫ Corp. Intel® and Celeron® are registered trademarks of Intel Corporation ⚫ Intel Core™ is a registered trademark of Intel Corporation ⚫...
- Page 4 Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UP Xtreme i11 EDGE System If any of these items are missing or damaged, please contact your distributor or sales representative immediately. Preface...
- Page 5 About this Document This User’s Manual contains all the essential information, such as detailed descriptions, and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings and definitions, and driver installation instructions (if any) to facilitate users in setting up their product Users may refer to the product page at AAEON.com for the latest version of this document.
- Page 6 Safety Precautions Please read the following safety instructions carefully. It is advised to keep a printed copy of this manual in an easy to access location for reference. All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
- Page 7 If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
- Page 8 FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
- Page 9 China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON System QO4-381 Rev.A0 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联 多溴二苯 苯(PBB) 醚(PBDE) (Pb) (Hg) (Cd) (Cr(VI)) 印刷电路板 × ○ ○ ○ ○ ○ 及其电子组件 外部信号 × ○ ○ ○ ○ ○ 连接器及线材 外壳 ○...
- Page 10 China RoHS Requirement (EN) Hazardous and Toxic Materials List AAEON System QO4-381 Rev.A0 Hazardous or Toxic Materials or Elements Component Name PCB and Components Wires & Connectors for Ext.Connections Chassis CPU & RAM HDD Drive LCD Module Optical Drive Touch Control Module Battery This form is prepared in compliance with the provisions of SJ/T 11364.
-
Page 11: Table Of Contents
Table of Contents Chapter 1 - Product Specifications ..................1 Specifications ........................2 Chapter 2 – Hardware Information ..................4 Dimensions ........................5 Jumpers and Connectors ....................7 List of Jumpers and Connectors ................. 10 2.3.1 Power Button (SW1) .................... 11 2.3.2 RTC (CN1) ...................... - Page 12 2.3.23 Audio Jack (CN33) ..................... 30 2.3.24 Fan Connector (J1) ..................... 30 2.3.25 AT/ATX Mode Jumper (JP1) ................31 2.3.26 GPIO Terminal Block..................32 Chapter 3 – Software Installation ..................33 Linux Setup ........................34 Windows Drivers Installation ..................34 Dummy Driver Installation ..................
-
Page 13: Chapter 1 - Product Specifications
Chapter 1 Chapter 1 - Product Specifications... -
Page 14: Specifications
Specifications System 11th Gen Intel® Core™ Processor SoC Core i7-1185GRE Core i5-1145GRE Core i3-1115GRE Celeron® 6305E Memory DDR4 SO-DIMM Slot x 2 (up to 64GB 3200MHz) Graphics Intel® Iris® Xe Graphics Storage SATA Connector (with Power) x 1 M.2 2280 M-Key NVMe (PCIe [x2]) Ethernet Intel®... - Page 15 Ethernet Intel® i225IT x 1 Intel® i219 (with vPro) x 1 COM Ports RS232/422/485 x 2 Environment and Dimensions Power Supply 12V (AT & ATX) Dimensions 124 mm x 152 mm x 66.5mm Gross Weight 2.3 kg Operating Temperature 32°F ~ 140°F (0°C ~ 60°C) Operating Humidity 0% ~ 90% relative humidity, non-condensing Certification...
-
Page 16: Chapter 2 - Hardware Information
Chapter 2 – Hardware Information Chapter 2... -
Page 17: Dimensions
Dimensions System Dimensions GPIO LAN 1G HDMI WiFi/BT USB3.2 USB3.2 WiFi/BT LAN 2.5G USB2.0 COM 3 USB4.0 WiFi/BT COM4 Chapter 2 – Hardware Information... - Page 18 Board Dimensions Chapter 2 – Hardware Information...
-
Page 19: Jumpers And Connectors
Jumpers and Connectors UPX-EDGE-TGL01 System: Chapter 2 – Hardware Information... - Page 20 Board Top: Chapter 2 – Hardware Information...
- Page 21 Board Bottom: Chapter 2 – Hardware Information...
-
Page 22: List Of Jumpers And Connectors
List of Jumpers and Connectors Please refer to the table below for all of the board’s jumpers and connectors that you can configure for your application Label Function Power Button HDMI/DP Dual Port eDP Connector SATA Connector USB Type A Dual Port USB Type A Dual Port CN10 USB Type C... -
Page 23: Power Button (Sw1)
Label Function Terminal Block GPIO 2.3.1 Power Button (SW1) Signal Signal PWR_SW# PWR_SW# SW1_LED_P SW1_LED_N 2.3.2 RTC (CN1) Signal RTC_VCC Chapter 2 – Hardware Information... -
Page 24: Hdmi/ Dp Dual Port (Cn2)
2.3.3 HDMI/ DP Dual Port (CN2) Signal Signal DP_TXP0 DP_TXN0 DP_TXP1 DP_TXN1 DP_TXP2 DP_TXN2 DP_CLK+ DP_CLK- CONFIG1 CONFIG2 DP_AUX_P DP_AUX_N DP_HPD 3.3V HDMI_TXP0 HDMI_TXN0 HDMI_TXP1 HDMI_TXN1 HDMI_TXP2 HDMI_TXN2 HDMI_CLK+ HDMI_CLK- HDMI_CEC DDC_CLK DDC_DATA HDMI_HPD Chapter 2 – Hardware Information... -
Page 25: Edp (Cn3)
2.3.4 eDP (CN3) Signal Signal +VDD_3V3 +VDD_3V3 EDP_TXN2 EDP_TXP2 EDP_TXN1 EDP_TXP1 EDP_TXN0 EDP_TXP0 EDP_TXN3 EDP_TXP3 EDP_AUXN EDP_AUXP BKLT_CTRL BKLT_EN EDP_HPD +12V +12V +12V +12V Chapter 2 – Hardware Information... -
Page 26: Sata Connector (Cn4)
2.3.5 SATA Connector (CN4) Signal Signal SATA_TXP0_C SATA_TXN0 SATA_RXN0 SATA_RXP0 2.3.6 USB Type A Dual Port (CN8) Signal Signal USB2_D1- USB2_D1+ USB3_RX1- USB3_RX1+ USB3_TX1- USB3_TX1+ USB2_D2- USB2_D2+ Chapter 2 – Hardware Information... -
Page 27: Usb Type A Dual Port (Cn9)
2.3.7 USB Type A Dual Port (CN9) Signal Signal USB2_D3- USB2_D3+ USB3_RX3- USB3_RX3+ USB3_TX3- USB3_TX3+ USB2_D4- USB2_D4+ USB3_RX4- USB3_RX4+ USB3_TX4- USB3_TX4+ Chapter 2 – Hardware Information... -
Page 28: Usb Type C (Cn10)
2.3.8 USB Type C (CN10) Signal Signal SSTXP1 SSTXN1 SBU1 SSRXN2 SSRXP2 SSTXP2 SSTXN2 SBU2 SSRXN1 SSRXP1 Chapter 2 – Hardware Information... -
Page 29: Usb 2.0/Uart 1X10P Wafer (Cn11)
2.3.9 USB 2.0/UART 1x10P Wafer (CN11) Signal Signal USB2_D5- USB2_D5+ USB2_D6- USB2_D6+ UART_RX UART_TX 2.3.10 M.2 2230 E Key Slot (CN12) Signal Signal +3.3V USB2_D10+ +3.3V USB2_D10- CNV_WR_LANE1_DN CNV_RF_RST# CNV_WR_LANE1_DP CNV_CLKREQ_R CNV_WR_LANE0_DN Chapter 2 – Hardware Information... - Page 30 Signal Signal CNV_WR_LANE0_DP CNV_WR_CLK_DN CNV_RGI_RSP_R CNV_WR_CLK_DP CNV_RGI_DT CNV_RGI_RSP PCIE9_TXP CNV_BRI_DT PCIE9_TXN PCIE9_RXP PCIE9_RXN PCIE5_CLKP PCIE9_CLKN SUS_CLK WIFI_RST# PCIE_CLKREQ# BT_EN PCIE_WAKE# WIFI_EN CNV_WT_LANE1_DN CNV_WT_LANE1_DP CNV_WT_LANE0_DN CNV_WT_LANE0_DP Chapter 2 – Hardware Information...
-
Page 31: 2280 M Key Slot (Cn13)
Signal Signal CNV_WT_CLK_DN +3.3V CNV_WT_CLK_DP +3.3V 2.3.11 M.2 2280 M Key Slot (CN13) Signal Signal +3.3V +3.3V +3.3V +3.3V +3.3V +3.3V PCIE1_RXN PCIE1_RXP Chapter 2 – Hardware Information... - Page 32 Signal Signal PCIE1_TXN PCIE1_TXP SSD_DEV_SLP SMB_CLK_1V8 PCIE0_RXN SMB_DATA_1V8 PCIE0_RXP PCIE0_TXN PCIE0_TXP PLT_RST# PCIE_CLKREQ# PCIE3_CLKN PCIE_WAKE# PCIE3_CLKP +3.3V +3.3V +3.3V Chapter 2 – Hardware Information...
-
Page 33: 3052 B Key Slot (Cn14)
2.3.12 M.2 3052 B Key Slot (CN14) Signal Signal +3.3V +3.3V FULL_CARD_POWER_OFF# USB2_D8+ W_DISABLE#1 USB2_D8- USB3_RX- UIM_RST USB3_RX+ UIM_CLK UIM_DAT USB3_PX- UIM_PWR USB3_PX+ PCIE10_RXN Chapter 2 – Hardware Information... - Page 34 Signal Signal PCIE10_RXP PCIE10_TXN PCIE10_TXP PLT_RST#(3.3V) PCIE_CLKREQ# PCIE4_CLKN PCIE_WAKE# PCIE4_CLKP PLT_RST#(1.8V) +3.3V +3.3V +3.3V Chapter 2 – Hardware Information...
-
Page 35: Lan Dual Port (Cn15)
2.3.13 LAN Dual Port (CN15) Signal Signal LAN1_MDI0+ LAN1_MDI0- LAN1_MDI1+ LAN1_MDI1- LAN1_MDI2+ LAN1_MDI2- LAN1_MDI3+ LAN1_MDI3- R10A LAN1_ACTLED- LAN1_ACTLED+ LAN1_LINK1000# LAN1_LINK100# LAN2_MDI0+ LAN2_MDI0- LAN2_MDI1+ LAN2_MDI1- LAN2_MDI2+ LAN2_MDI2- LAN2_MDI3+ LAN2_MDI3- R10B LAN2_ACTLED- LAN2_ACTLED+ LAN2_LINK1000# LAN2_LINK100# Chapter 2 – Hardware Information... -
Page 36: Pci Express Slot (Cn18)
2.3.14 PCI Express Slot (CN18) Signal Signal +12V +12V +3.3V +3.3V PLT_RST# PCIE0_CLKP PCIE0_CLKN PCIE4_P0_RXP PCIE4_P0_RXN PCIE4_P1_RXP PCIE4_P1_RXN PCIE4_P2_RXP PCIE4_P2_RXN PCIE4_P3_RXP PCIE4_P3_RXN +12V +12V +12V SMB_CLK SMB_DATA +3.3V +V3.3A PCIE_WAKE# Chapter 2 – Hardware Information... -
Page 37: 40-Pin Hat Connector (Cn19)
Signal Signal PCIE4_P0_TXP PCIE4_P0_TXN PCIE4_P1_TXP PCIE4_P1_TXN PCIE4_P2_TXP PCIE4_P2_TXN PCIE4_P3_TXP PCIE4_P3_TXN 2.3.15 40-Pin HAT Connector (CN19) Note: PWM function (Pin 32, 33) only supported with UP Framework SDK. UPX-TGL only has one PWM controller, and cannot output two different frequencies for PWM0 and PWM1. -
Page 38: Cpld And Bios Update (Cn20)
Signal Signal GPIO6 GPIO19 +3.3V GPIO20 SPI_MOSI/ GPIO7 SPI_MISO/ GPIO8 GPIO21 SPI_CLK/ GPIO9 SPI_CS0/ GPIO22 SPI_CS1/ GPIO23 I2C0_DAT/ GPIO10 I2C0_CLK/ GPIO24 GPIO11 GPIO12 PWM0/ GPIO25 PWM1/ GPIO13 I2S_SYNC/ GPIO14 GPIO26 GPIO15 I2S_SDI/ GPIO27 I2S_SDO/ GPIO28 2.3.16 CPLD and BIOS Update (CN20) Signal Signal JTAG_TCK... -
Page 39: Dc Jack (Cn21)
2.3.17 DC Jack (CN21) Signal DC_IN 2.3.18 Front Panel (CN22) Signal Signal RESET POWER S/W +3.3V Chapter 2 – Hardware Information... -
Page 40: Dc Terminal Block (Cn23)
2.3.19 DC Terminal Block (CN23) Signal DC_IN 2.3.20 COM3, COM4 RS232/ 422/ 485 (CN28/CN29) Signal Signal DCD/ RS422TX-/ S485- RX/ RS422TX+/ RS485+ TX/ RS422RX+ DTR/ RS422RX- Chapter 2 – Hardware Information... -
Page 41: Atx Power (Cn31)
2.3.21 ATX Power (CN31) Signal Signal 12V OUT 12V OUT 2.3.22 SATA Power (CN32) Signal Chapter 2 – Hardware Information... -
Page 42: Audio Jack (Cn33)
2.3.23 Audio Jack (CN33) Signal Signal MIC_LR LOUT_R AUDIO-JD LOUT_L 2.3.24 Fan Connector (J1) Signal Signal TACH Chapter 2 – Hardware Information... -
Page 43: At/Atx Mode Jumper (Jp1)
2.3.25 AT/ATX Mode Jumper (JP1) Signal ATX_MODE PWRBTN AT_MODE ATX Mode (Default) AT Mode Chapter 2 – Hardware Information... -
Page 44: Gpio Terminal Block
2.3.26 GPIO Terminal Block Signal Signal PIN1 (3.3V) PIN2 (5V) PIN3 (I2C_SDA) PIN5 (I2C_SCL) PIN6 (GND) PIN9 (GND) PIN12 (GPIO) PIN13 (GPIO) PIN15 (GPIO) PIN16 (GPIO) PIN18 (GPIO) PIN19 (GPIO) PIN21 (GPIO) PIN22 (GPIO) PIN32 (PWM0) PIN33 (PWM1) Note: PWM function (PIN32, PIN33) only supported with UP Framework SDK Chapter 2 –... -
Page 45: Chapter 3 - Software Installation
Chapter 3 Chapter 3 – Software Installation... -
Page 46: Linux Setup
Linux Setup UP Xtreme I11 EDGE supports Linux operating systems (see Chapter 1 for specifications). For instructions on how to install a Linux OS onto your UP Xtreme I11 EDGE, you can find several guides and tutorials in the wiki section of the UP Board website at https://up-board.org for both installing supported distributions as well as... -
Page 47: Dummy Driver Installation
Dummy Driver Installation The following instructions detail how to install the dummy driver for UPX-EDGE-TGL01. Step 1 – Open Device Manager in Windows by searching for the app in the Start Menu. Chapter 3 – Software Installation... - Page 48 Step 2 – Under “Other devices” look for Intel High Definition Audio. Right click on the device and select “Update driver”. Step 3 – Select “Browse my computer for drivers” Chapter 3 – Software Installation...
- Page 49 Step 4 – Click “Browse…” and select the folder where you saved the dummy driver software. Chapter 3 – Software Installation...
- Page 50 Step 5 – Repeat for Unknown device Chapter 3 – Software Installation...
-
Page 51: Appendix A - Up Framework Sdk Installation
Appendix A Appendix A – UP Framework SDK Installation... -
Page 52: Introduction
Introduction This section provides instructions for the installation of the UP Framework SDK. Instructions are provided for Windows 10 and Windows IoT Core. You can download the latest version of UP Framework SDK from the UP community: https://downloads.up-community.org/download/up-sdk-for-windows-10-and-windows-iot/ Installation for Windows 10 Step 1 Locate the downloaded file UpFrameworkSetup.msi and run the installer. - Page 53 Step 2 Select the installation folder. Default destination path is C:\Program Files(x86)\AAEON\ You may also choose to install the UP Framework SDK for all users or only the current user. Press “Next” to continue installation. Step 3 Press “Next” to confirm the installation. Step 4 Press “Close”...
- Page 54 Appendix A – UP Framework SDK Installation...
-
Page 55: Installation For Windows Iot Core
Installation for Windows IoT Core Before you begin, make sure you have downloaded and installed the latest version of the Windows IoT Core image from the UP community. Installation requires using a connected PC with the UP Framework SDK software downloaded and saved. - Page 56 Step 2 Download the UP Framework SDK to your PC and unzip the files. Open PowerShell as an Administrator. Enter the command RemoteInstallation.ps1 to install the UP Framework SDK. Enter the IP address of the UP IoT Core device when prompted. Appendix A –...
-
Page 57: Appendix B - Cables And Connectors
Appendix B Appendix B – Cables and Connectors... -
Page 58: Cables And Connectors
Cables and Connectors This table provides detailed information about the cables and connectors used by the UP Xtreme I11 EDGE (UPX-EDGE-TGL01). If you have any questions about the configuration of your board, please contact your AAEON sales representative. Mating Mating Cable Label Connector PN Description... - Page 59 Mating Mating Cable Label Connector PN Description Cable PN Description DC Power Jack.3P (DC CN21 165250320K 12V) Wafer Box.6P. Front CN22 1655906033 Panel (Power on + Reset) COM Port.9P.COM Wafer Box.10P. COM Cable to CN28 1655901000 170X000255 port VGA.210mm.FLYINGW AY.FWAA-1375. COM Port.9P.COM Wafer Box.10P.