Table of Contents
Advertisement
Inserting the Batteries into the Remote
The remote may have a screw that secures the battery
compartment cover onto the remote control (or this
may be in a separate bag). Remove the screw, if
the cover is screwed on previously. Then remove
the battery compartment cover to reveal the battery
compartment. Insert two size AAA batteries. Make
sure the (+) and (-) signs match (observing correct
polarity). Do not mix old and new batteries. Replace
only with same or equivalent type. Place the cover
back on. Secure the cover again with the screw, if any.
While using the remote control, direct it towards the
front side of the receiver. If the remote control does
not work or the chosen function does not work, the
batteries are most probably exhausted and they
should be replaced as soon as possible. Please use
only the leak proof batteries. It is best to remove the
batteries from the remote unit if you will not be using
the remote control unit for long time.
Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
First Time Installation
When turned on for the first time, the language
selection screen is displayed. Select the desired
language and press OK. In the following steps of
the installation guide, set your preferences using the
directional buttons and OK button.
After the language selection, you will be asked
whether you want to change accessibility settings.
Highlight Yes and press OK to change. Refer
to System Menu Content section for detailed
information on available options.
Set your country preference on the next screen.
Depending on the country selection you may be asked
to set and confirm a PIN at this point. The selected
PIN cannot be 0000. You have to enter it if you are
asked to enter a PIN for any menu operation later.
On next screen you can set your time zone preference.
If you set the Time zone setting option to Manual,
you can set the Time Zone option manually. When
you are done highlight Next and press OK to proceed.
You can set your TV Type, Display Format, and HDMI
Resolution preferences in the next step. Highlight
each option and use the Left or Right directional button
to change the setting. Highlight Next and press OK
to proceed.
On next screen you can set broadcast type/s to be
searched, set your encrypted channel searching
preferences. Additionally you can set a broadcast
type as your favourite one. Priority will be given to the
selected broadcast type during the search process
and the channels of it will be listed on the top of the
channel list. When finished, highlight Next and press
OK to continue.
About Selecting Broadcast Type
To turn a search option for a broadcast type highlight
it and press OK. The checkbox next to the selected
option will be checked. To turn the search option off
clear the checkbox by pressing OK after moving the
focus on the desired broadcast type option.
Digital Aerial: If the D. Aerial broadcast search option
is turned on, the box will search for digital terrestrial
broadcasts.
After the initial settings are completed the set-top
box will start to search for available broadcasts of the
selected broadcast type/s.
While the search continues current scan results will
be displayed at the bottom of the screen. After all the
available stations are stored, the Channels menu will
be displayed. You can edit the channel list according
to your preferences using the Edit and Filter tab
options or press the Menu button to quit and watch
TV channels. Refer to the Channel List section for
more information.
While the search continues a message may appear,
asking whether you want to sort channels according
to the LCN (*). Select Yes and press OK to confirm.
(*) LCN is the Logical Channel Number system that organises
available broadcasts in accordance with a recognisable
channel number sequence (if available).
Note: Do not turn off the box while initialising first time
installation. Note that, some options may not be available
depending on the country selection.
Using Main Menu
When the Menu button is pressed, the main menu
will appear on the screen. You can navigate through
the menu items using the directional buttons on the
remote. To select an item or see the sub-menu options
of the highlighted menu press the OK button. When
you highlight a menu option some of the sub-menu
items of this menu may appear on the upper side of
the menu bar for quick access. To use a quick access
item highlight it, press OK and set as desired using
the Left/Right directional buttons. When finished press
the OK or Back/Return button to exit.
Press the Exit button to close the main menu.
1. Home
When main menu is opened the Home menu bar will
be highlighted. The content of the Home menu can
be customised by adding options from other menus.
Just highlight an option and press the Down direction
button on the remote. If you see the Add to Home
option you can add it to the Home menu. Same way
you can delete or change the position of any item in
the Home menu. Press the Down direction button
and select the Delete or Move option and press OK.
In order to move a menu item use the Right and Left
English - 8 -
Advertisement
Table of Contents
