Maintenance; Troubleshooting - THOMSON ROC1128SAM Manual

2. Then press and release the target key on
the remote control you want learned.
3. If the LED flashes 3 times and then remain
on, the command has been learned
successfully.
4. Repeat these steps to learn other key
functions.
5. Press the [MUTE] and [VOL-] buttons to
save all learnt functions and to exit the
learning mode.
Note
While replacing the batteries, the remote control
will keep the functions of the learned keys.
6.4 CLEARING OF LEARNED KEYS
6.4.1 CLEARING OF ONE LEARNED KEY
1. Press and hold [MUTE] and [VOL+] keys
for 5 seconds until the LED will be lit.
2. Enter the code [9] [8] [1], the LED will
flash 2 times and then remain on.
3. Press and release the desired key at the
replacement remote control which you
want to clear the learned command. If the
LED flashes 3 times, the learned command
has been cleared successfully.
6.4.2 CLEARING OF ALL LEARNED KEYS
1. Press and hold [MUTE] and [VOL+] keys for
5 seconds until the LED will be lit.
1. Enter the code [9] [8] [2], the LED will flash
2 times and then remain on.
2. Press and release the [OK] key at the
replacement remote control. If the LED
flashes 3 times, all commands have been
cleared successfully.
7. SIMPLE Mode
This remote control is equipped with an SIMPLE
Mode. Thus you could reduce the functionality of
the remote control to its basic functions. It avoids
that the TV Settings are changed by mistake.
During the SIMPLE Mode you still could use
following keys:
POWER TV ON / OFF
VOL Change your TV's volume
TV Mute
CH Channel up/down
0-9 Numeric keys 0 – 9 to enter channel
numbers
TTX/MIX Teletext ON / OFF / MIX
Use to select a variety of on screen
options
GUIDE Show the Electronic Program Guide
(if supported by the TV)
Input signal source / Indicator LED
5
5
Turn off the menu of the selected
product
TV Switch to signal source TV
7.1 Enter SIMPLE Mode
1. Press and hold [MUTE] and [VOL+] keys for
5 seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash
two times and then remain on.
3. Press and release the [OK] key, if LED flash
3 times, you have entered the SIMPLE
Mode successfully
7.2 Exit SIMPLE Mode
1. Press and hold [MUTE] and [VOL+]
for 5 seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash
two times and then remain on.
3. Press and release the [EXIT] key, if LED
flash 3 times, you have exit the SIMPLE
Mode.
Note
While the SIMPLE Mode is activated only
the keys mentioned in chapter 7. will work.
If one of these keys is pressed the LED will
be lit until the key is released. If one key is
pressed during the normal mode, the LED
will flash.

8. Maintenance

• Do not mix new and used batteries for
powering the Universal Remote Control, as
old batteries tend to leak and may cause
power drain.
• Do not use corrosive or abrasive cleansers on
your Universal Remote Control.
• Keep the Universal Remote Control dust free
by wiping it with a soft, dry cloth.

9. Troubleshooting

Q. My Universal Remote Control does not
work at all!
A. Check your TV. If the TV main switch is
turned off, your Remote cannot operate
your TV.
A. Check whether your batteries are inserted
properly and are in the correct +/- position.
A. If the batteries are low, replace the
batteries.
Q. My TV responds only to some of the
commands.
A. Try other codes until most keys work
properly.
Q. Some keys of the Remote Control do not
work anymore?
A. Maybe the SIMPLE Mode had been
activated. Deactivate the SIMPLE Mode as
explained in chapter 7.2.
4
5
5