Table of Contents
Advertisement
2
Select Replace Data.
3
Select a data type.
4
Select the data to display.
Customizing the Gauges
You can change the layout of the gauge pages, how the gauges
pages are displayed, and the data in each gauge.
1
Open a gauge page.
2
Select Menu > Edit Gauge Pages.
3
Select an option:
• To change the data shown in a gauge, select the gauge.
• To change the layout of the gauges on the page, select
Change Layout.
• To add a page to this set of gauge pages, select Add
Page.
• To change the order of this page in the set of gauge
pages, select Move Page Left or Move Page Right.
• To restore this page to the original view, select Restore
Default View.
Customizing Engine Gauge and Fuel Gauge Limits
You can configure the upper and lower limits and the range of
desired standard operation of a gauge.
NOTE: Not all options are available for all gauges.
1
From an applicable gauges screen, select Menu >
Installation > Set Gauge Limits.
2
Select a gauge to customize.
3
Select an option:
• To set the minimum value of the standard operating
range, select Rated Min..
• To set the maximum value of the standard operating
range, select Rated Max..
• To set the lower limit of the gauge lower than the rated
minimum, select Scale Min..
• To set the upper limit of the gauge higher than the rated
maximum, select Scale Max..
4
Select the limit value.
5
Repeat steps 4 and 5 to set additional gauge limits.
Selecting the Number of Engines Shown in Gauges
You can show information for up to four engines.
1
From the engine gauges screen, select Menu > Installation
> Engine Selection > Num. Engines.
2
Select an option:
• Select the number of engines.
• Select Auto Configure to automatically detect the number
of engines.
Customizing the Engines Shown in Gauges
Before you can customize how the engines are shown in the
gauges, you must manually select the number of engines
(Selecting the Number of Engines Shown in Gauges, page
1
From the engine gauges screen, select Menu > Installation
> Engine Selection > Num. Engines.
2
Select First Engine.
3
Select the engine to display in the first gauge.
4
Repeat for the remaining engine bars.
Enabling Status Alarms for Engine Gauges
You can enable the chartplotter to display engine status alarms.
From the engine gauges screen, select Menu > Installation
> Status Alarms > On.
46
When an engine alarms is triggered, a gauge status alarm
message appears and the gauge may become red depending
on the type of alarm.
Enabling Some Engine Gauge Status Alarms
1
From the engine gauges screen, select Menu > Installation
> Status Alarms > Custom.
2
Select one or more engine gauge alarms to turn on or off.
Yamaha Engine Gauges
Select A/V, Gauges, Controls > YAMAHA to view the Yamaha
engine gauges. This screen varies based on the engine network
and throttle controller.
Data fields
Hold to replace the data.
Current time
Hold to view trip data.
Press to set the joystick button Set Point functions (Helm Master
Tank level information
Hold a tank to view detailed tank level sensor information.
GPS signal strength
Select to set the Fish Point high RPM limit (Helm Master).
Select to set the trolling speed (Command Link Plus
Data fields
Hold to replace the data.
Shift position
Tachometer and trim angle
Hold to change the background.
Engine information
Hold to replace the data and change the gauge appearance.
Engine Condition Icons
Orange icons indicate engine conditions.
Yamaha security system is on.
Engines are under synchronization control.
Engines are warming up.
Engine Alert Icons
Red icons indicate engine abnormalities.
Consult your Yamaha dealer if the problem cannot be located
and corrected.
46).
Low cooling water pressure.
Low oil pressure.
Stop the engine. Check the engine oil level, and add more oil if
necessary.
Do not continue to run the engine if this indicator is on. Serious
engine damage will occur.
®
).
NOTICE
NOTICE
Gauges and Graphs
®
).
Advertisement
Table of Contents
