Table of Contents
Advertisement
Operating Instructions
Troubleshooting (continued)
Video
„
„
Symptom
No pictures are displayed or
the pictures are disturbed
The picture is flipped
vertically
Multiple color bands (color
bars) are displayed
The menu screen is displayed
It is difficult to view the menu
screens
No auto focusing
The subject is not brought
into focus
during zooming when the
manual setting is used for the
focus
Focusing is not possible in
night mode
1080/29.97PsF images appear
jerky
1080/25PsF images appear
jerky
64
Cause and solution
• Has the unit been connected properly to the other connected devices?
• If the system is configured in such a way that the picture is also
switched when the unit to be operated is selected, has the correct unit
been selected?
• Has the image signal setting been selected correctly?
• Are external sync signals that are supported by the video signal
format which has been set being input?
• Has the stand-alone (Desktop) installation setting been selected
correctly?
• Switch to the camera picture.
• Exit the camera menu.
• Depending on the HDMI monitor you are using, you may experience
one or more of the symptoms described below.
• The resolution of the characters in the camera menu displays changes as
the background image changes.
• Depending on the edge enhancement setting established for the monitor,
white lines appear in front of the black shadows of the camera menus.
• Depending on the edge enhancement setting established for the monitor,
the background colors may be superimposed onto the white parts of the
camera menus.
• Is the focus set to manual?
→ Auto focusing is initiated as soon as the focus is set to auto.
• In some situations, it may be hard to focus at the auto setting.
→ In cases like this, select the manual setting, and focus manually.
• Was the focus adjusted at the Tele end?
→ First adjust the focus at the Tele end where the focusing accuracy is
higher, and then proceed with the zooming.
• Under some operating conditions, it may be hard to bring subjects
into focus.
→ In such cases, use the focus at the auto setting.
• Are you shooting with visible light?
→ The focus position is different due to the difference in refractive index
between visible light and infrared light. Wavelengths near 850 nm are
assumed for infrared light in night mode on this unit.
Perform manual adjustment if necessary.
• This is normal operation.
→ In the PsF (Progressive segmented Frame) format, an identical image
is captured to fields 1 and 2 in order to output the same image as
progressive. Therefore, the image will appear slightly jerky.
• This is normal operation.
→ In the PsF (Progressive segmented Frame) format, an identical image
is captured to fields 1 and 2 in order to output the same image as
progressive. Therefore, the image will appear slightly jerky.
Reference pages
pages 18 to 21
Operating Instructions (PDF)
→ "Selecting the units"
Operating Instructions (PDF)
→ "Camera menu items"
→ "System screen"
→ "Format"
Operating Instructions (PDF)
→ "Web screen configurations"
→ "Basic screen [Basic]"
→ "System screen [System]"
→ "Format"
page 48
Operating Instructions (PDF)
→ "Camera menu items"
→ "Pan/Tilt screen"
→ "Install Position"
Operating Instructions (PDF)
→ "Web screen configurations"
→ "Basic screen [Basic]"
→ "System screen [System]"
→ "Pan/Tilt"
→ "Install Position"
Operating Instructions (PDF)
→ "What to do when encountering
problems in the basic shooting operations"
Operating Instructions (PDF)
→ "Basic setup operations"
– – –
Operating Instructions (PDF)
→ "What to do when encountering
problems in the basic shooting operations"
Operating Instructions (PDF)
→ "Manual shooting"
→ "Manually adjusting the focus"
– – –
Operating Instructions (PDF)
→ "What to do when encountering
problems in the basic shooting operations"
Operating Instructions (PDF)
→ "Manual shooting"
→ "Manually adjusting the focus"
– – –
– – –
Advertisement
Table of Contents
