Page 1: Table Of Contents
Electrical connection Positioning Preliminary operations We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance’s aesthetic and functional qualities. For further information on the product: www.smeg.com PRECAUTIONS General safety instructions appliance and smother the...
Page 2 are constantly supervised. APPLIANCE. • Keep children under the age of • Installation and servicing should 8 away from the appliance be carried out by qualified when it is in use. personnel in accordance with • Cleaning and maintenance current standards. must not be carried out by •...
Page 3 oven cavity. interfere with the hot air circulation inside the oven cavity. • Do not use the open door to rest pans or trays on the internal glass pane. • Never use the oven door to • Do not use steam jets to clean lever the appliance into place the appliance.
Page 4: For This Appliance
installed on a pedestal. • Disconnect the appliance after • Position the appliance into the the installation, through an cabinet cut-out with the help of accessible plug or switch in a second person. case of fixed connection. • To prevent any possible •...
Page 5: Appliance Purpose
Appliance purpose Disposal This appliance conforms to the WEEE This appliance is intended for European directive (2012/19/EU) and cooking food in the home must be disposed of separately from environment. Every other use is other waste at the end of its service life. The appliance does not contain substances in considered inappropriate.
Page 6: To Save Energy
These data are present in the "Product How to read the user manual information sheet" that can be downloaded This user manual uses the following reading from the website at the page dedicated to the conventions: product in question. To save energy Warning/Caution •...
Page 7: Description
DESCRIPTION General Description 1 Control panel 2 Seal 3 Light bulb 4 Light bulb (on some models only) 5 Door 6 Fan Frame shelf 91477A235/B DESCRIPTION - 9...
Page 8: Control Panel
Control panel 1 Function knob and racks at different heights. The insertion heights are indicated from the bottom upwards. This knob can be used to: • turn the appliance on and off; Cooling fan • select a function. Turn the Function knob to the position 0 to immediately complete any cooking operation.
Page 9: Accessories
• The interior lighting remains switched off Rack during the execution of the special functions and the cleaning functions (depending on the models). • When the door is opened, excluding the function, the lighting in the oven Used for supporting containers with food during cavity is switched on.
Page 10: Digital Programmer
the oven cavity. Showroom indicator light Defrost indicator light Temperature indicator light First use If the time is not set, the oven will not switch on. When using the appliance for the first time or Gently insert racks and trays into the oven until they come to a stop.
Page 11 cooking duration, cooking end time... The display shows flashing 2. Within 3 seconds turn the temperature knob When the door is opened, the function to change the temperature in progress is interrupted. The function resumes automatically 3. Press the temperature knob to set the when the door is closed.
Page 12 Programmed cooking for the set start time. Programmed cooking is the function which allows a cooking operation to be started at a set time and then ended after a specific length of time set by the user. For safety reasons, it is not possible to set the end of cooking time by itself The minutes required for preheating are without setting the cooking duration.
Page 13 FAN ASSISTED light flashes. Intense and uniform cooking. Ideal for biscuits, cakes and cooking on more than one level. CIRCULAIRE The heat is distributed quickly and uniformly. Suitable for all dishes, ideal for cooking on multiple levels without mixing smells or flavours. You can also set a minute minder timer also when cooking is in progress.
Page 14: Cooking Advice
through: At the end of the cooking time, put Cooking (and preheating) times are a toothpick into the highest point of the longer with the ECO function and may dessert. If the dough does not stick to the depend on the amount of food in the toothpick, the dessert is cooked.
Page 15: Mini Guide To Accessories
(from on cooking suggestions, we recommend visiting 1 minute to 13 hours). the dedicated page on the www.smeg.com 3. Wait 3 seconds. website, which can be reached using the QR The indicator light stops flashing and the code on the leaflet supplied with the product.
Page 16: Special Functions
3. Wait 3 seconds to exit the minute minder 5. Wait 3 seconds or press the temperature function. knob to start the function. Special functions 1. Turn the function knob until the following text is displayed. At the end, the flashing wording displayed and a buzzer will sound that can be deactivated by opening the door and/or pressing/turning any of the two knobs.
Page 17 5. At the end, turn the function knob to position function. 0 to exit the function. Sabbath mode This function results in the appliance operating in a particular way: • Cooking can proceed for max. 73 hours, it is not possible to set any cooking duration. 6.
Page 18: Settings
that can be deactivated by opening the door 2. Turn the temperature knob to select the and/or pressing/turning any of the two knobs. current time. To continue with the cooking of other pizzas, after deactivating the buzzer: • press the function knob again to start the function •...
Page 19 Control lock (children safety) Showroom (for showrooms only) This mode allows the appliance to lock This mode allows the appliance to the controls automatically after one deactivate all heating elements, while minute of normal operation without any keeping the control panel active. intervention from the user.
Page 20: Cleaning And Maintenance
3. Turn the temperature knob to activate the 4. Press the temperature knob to confirm. keep warm function. To use the appliance normally, set this function to OFF. CLEANING AND MAINTENANCE Cleaning the appliance 1. Open the door completely and insert two pins into the holes on the hinges indicated in the figure.
Page 21 4. Lower the door and once it is in place unit consists of two panes. remove the pins from the holes in the hinges. Cleaning the door glazing The glass in the door should always be kept thoroughly clean. Use absorbent kitchen roll. In case of stubborn dirt, wash with a damp sponge and an ordinary detergent.
Page 22: Cleaning The Oven Cavity
9. Reinsert the intermediate glass unit and • The rack/tray support frames. reposition the inner glass. In the event you are using specific cleaning products, we recommend running the oven at maximum temperature for 15-20 minutes in order to eliminate any residue. Drying Cooking food generates moisture inside the appliance.
Page 23 cavity (you can help yourself with a tool, 1. Slide the rear part of the frame into the e.g. a coin). housing under the pin B located at the bottom of the side wall. 2. Carefully pull the frame towards the inside of the oven cavity to unhook it from front 2.
Page 24: Special Cleaning Functions
Special cleaning functions Vapor Clean cycle setting 1. Turn the function knob until the following text If the internal temperature is greater appears on the display. than the one required, the function will be stopped immediately and the following message appears on the display: 2.
Page 25: Pyrolytic (On Some Models Only)
by opening the door or pressing/turning We recommend removing the door in one of the two knobs. order to make the manual cleaning of the parts that are difficult to reach easier. Pyrolytic (on some models only) See General safety instructions. 7.
Page 26 (factory set to 2 hours). During the Pyrolytic cycle the fans produce a more intense level of noise due to a greater rotation speed. This is an absolutely normal operation, intended to provide more effective heat dispersal. At the end of the pyrolytic cycle, the fans will continue to operate for long enough to avoid overheating 3.
Page 27: Extraordinary Maintenance
4. Slide out and remove the light bulb. Extraordinary maintenance Seal maintenance tips The seal should be soft and elastic. • To keep the seal clean, use a non-abrasive sponge and wash with lukewarm water. Replacing the internal light bulb Power voltage Danger of electrocution •...
Page 28: Positioning
Fixed connection Positioning Fit the power line with an all-pole circuit breaker with a contact separation distance sufficient to See General safety instructions. provide complete disconnection in category III overvoltage conditions, pursuant to installation Position of the power cable regulations. For the Australian/New Zealand market: The circuit breaker incorporated in the fixed connection must comply with AS/NZS 3000.
Page 29 Appliance overall dimensions (mm) 91477A235/B INSTALLATION - 31...
Page 30 Mounting into a column (mm) Make sure that the cabinet top/rear section has an opening approx. 35-40 mm deep. 32 - INSTALLATION 91477A235/B...
Page 31 Mounting under worktops (mm) If the appliance is to be built-in under a worktop, a wooden bar has to be installed order to use the seal that is glued to the back of the front panel to prevent water or other liquids leaking in. A min.
Page 32 A min. 603 mm B 560 - 568 mm C 583 - 585 mm D 9 - 11 mm E min. 5 mm F 121 - 1105 mm G min. 560 mm H min. 594 mm co Cutout for power cord (min. 6 cm jb Electrical connection box wb Wooden bar (recommended) Mounting under worktops (mm) (pyrolytic...
Page 33 When using a wooden separator, a wooden bar has to be installed under the worktop in order to use the seal that is glued to the back of the front panel to prevent water or other liquids leaking in. 91477A235/B INSTALLATION - 35...

Smeg SOPA6301TN Manual

Quick Links

PRECAUTIONS

General safety instructions

Related Manuals for Smeg SOPA6301TN

Summary of Contents for Smeg SOPA6301TN

Table of Contents