Preparation For Use; Clock Set Up - Sanyo VWM-950 Instruction Manual

3. Preparation for Use

Turn On the Unit for the First Time
1
1
Turn on the TV and
set it to channel 3.
• If channel 3 is already occu-
pied for broadcasting, see "RF Output
Channel" section.
2
2
Remote Control TV Screen
POWER
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
or
3
3
CH 01
AUTO SET UP
Do you connect the cable of the cable box or
the satellite box to the unit's ANT-IN jack?
Yes
Y es
Y es
Press [MENU] to
exit.
• Refer to "Hints for Cable Box or
Satellite Box" section on page 1.
No
No No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memorized
in this unit by using [CHANNEL ].
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections. Then,
press [F.FWD g g ] once again.
Hint
Hint
• Repeat these steps only if either there was
a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by using
the Number buttons on the remote
control.
Notes for using the Number
buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number. (For
example: 117, press [1], [1], [7])
• You must precede single-digit
channel numbers with a zero (For
example: 02, 03, 04 and so on).
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
2) Press [PLAY B B ] or [C C STOP] to select
"CHANNEL SET UP", then press
[F.FWD g g ].
3) Press [PLAY B B ] or [C C STOP] to select
"AUTO SET UP", then press
[F.FWD g g ]. After scanning, the tuner stops
on the lowest memorized channel.
To Change the On-Screen Language
1) Press [MENU] until the main menu appears.
2) Press [PLAY B B ] or [C C STOP] to select
"LANGUAGE SELECT", then press
[F.FWD g g ].
3) Press [PLAY B B ] or [C C STOP] to select
"ENGLISH" , "FRANCAIS" or "ESPAÑOL",
then press [C.RESET/EXIT].
Hint Hint
• If you accidentally select Spanish or French
and need English: Press [MENU] and
choose SELEC. IDIOMA, or SELECTION
LANGUE. Press [F.FWD g g ] and select
ENGLISH. Finally, press [C.RESET/EXIT].
Need help? Call
1-800-813-3435
To Add/Delete Channels
1
1
MENU
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
or
2
2
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
or
3
3
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
or
Select the channel to be
added or deleted.
4
4
MANUAL SET UP
CHANNEL 30 (CATV)
or DELETE
Select "ADD" or "DELETE".
5 5
To exit the C.RESET
EXIT
menu
- 3 -

Clock Set Up

1
1
MENU
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
• If the clock is not set, the
or
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
2
2
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
or
– – : – – – –
Select the current month.
3 3
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 – – – –
or HOUR MINUTE AM/PM
– – : – – – –
Select the current day.
4
4
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 2 0 0 5
or HOUR MINUTE AM/PM
– – : – – – –
Select the current year.
5
5
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
or
0 5 : – – – –
Select the current hour.
6
6
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
or
0 5 : 4 0 – –
Select the current minute.
7
7
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
or
0 5 : 4 0 P M AM
B PM
Select "AM" or "PM".
8 8
To exit the CLOCK SET
screen
Hint
Hint
h h
• To go back one step, press [ REW]
(during the steps 2) to 7)).
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
EN