Related Manuals for HAMPTON BAY Minuet III AG806C-EB
Summary of Contents for HAMPTON BAY Minuet III AG806C-EB
- Page 1 Model: AG806C-EB 122 888 120 V~ 60 Hz 110 W Read and follow all the instructions before using this product. Minuet III Ceiling Fan Owner’s Manual Minuet III Ventilador de Techo de 91,4 Manual del Propietario...
- Page 2 Minuet III by Hampton Bay ®...
- Page 3 VENTILADOR DE TECHO/CEILING FAN Marca/Brand: Hampton Bay Modelo/Model: 122888 120 V~ 60 Hz 110 W Consumo de energía por unidad de tiempo en operación (Energy Consumption): 98.52 Wh Importador/Importer: SERVICIOS HOME DEPOT, S. DE R.L. DE C.V. Ricardo Margain 605, Santa Engracia, San Pedro Garza García, Nuevo León, C.P.
-
Page 4: Table Of Contents
36” (91,4 cm) Minuet III Ceiling Fan by Hampton Bay Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Date Purchased Table of Contents Store Purchased Safety Rules ....1 122-888 Model No. -
Page 5: Safety Rules
Safety Rules - Read and Save These Instructions To reduce the risk of electric shock, insure electricity has been turned off After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning. upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding All wiring must be in accordance with the National Electrical Code conductor on one side of the outlet box and ungrounded conductor on the... -
Page 6: Unpacking Your Fan
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: Set of blades (6) Set of blade arms (6) Blade Attachment Hardware (19 Screws with fiber Washers) Canopy assembly Light fixture Ball/downrod assembly Glass shade Electrical Hardware (3 Plastic Wire Nuts) Coupling cover... -
Page 7: Installing Your Fan
Installing Your Fan Provide Strong Support Tools Required Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Ceiling Outlet Box Mounting Plate Mounting Options Figure 3 Outlet Box Note: You may need a longer downrod to If there isn't an existing UL listed mounting box,... - Page 8 Hanging the Fan Motor Wires Remove the Pin in Locked Canopy Ring Positioon Ball/Downrod REMEMBER to turn off the power. Follow the Assembly steps below to hang your fan properly. Ceiling Canopy NOTE: This ceiling fan is supplied with two types Canopy Ring of hanging assemblies;...
- Page 9 NOTE: If a longer downrod is needed, take out Motor Remove the decorative canopy bottom cover the screw located in the hanger ball, lower the from the canopy by turning the canopy bottom Collar Screw and Lock Washer cover counterclockwise (Figure 8). (3 of 6 Places) hanger ball and remove the pin, remove all 3 pieces from the downrod and assemble them onto...
- Page 10 Installing Fan to NOM Listed Outlet Box the Electrical Box WARNING 120V Wires TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE Groove FOR FAN SUPPORT AND USE THE MOUNTING Ceiling Mounting SCREWS PROVIDED WITH THE OUTLET BOX.
- Page 11 Making the Electrical Connect the fan motor black wire to the supply SUPPLY CIRCUIT black (hot) wire using a wire nut. (Figure 13) Connections Connect the blue wire for light kit to the black Ground REMEMBER to disconnect the power. household supply wire.
- Page 12 Finishing the Fan Close-to-Ceiling Mounting Installation Outlet Box Remove the fan from the tab on the hanger bracket. Secure the canopy to the hanger bracket Standard Ceiling Mounting with four screws included with your fan. (Fig. 15) Hanger Raise up canopy ring and line up the 4 tabs with Screws WARNING Bracket...
- Page 13 Attaching the Fan Blades NOTE MOTOR IS SHIPPED WITH RUBBER PACKING Motor MOUNTS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE RUBBER PACKING MOUNTS FROM MOTOR ASSEMBLY DISCARD PRIOR ATTACHING BLADE ARMS. (FIG. 16) Attach blades to blade arms using three screws Rubber packing mounts with fiber washers (Fig.
- Page 14 Blade Balancing All blades are grouped by weight during assembly. Because natural woods vary in density, the fan may wobble even though the blades are weight Touching Ceiling matched. The following procedure should correct most fan wobble. Check after each step. Verify that all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts).
-
Page 15: Installing The Light Kit
Installing the Light Kit Fan without Light Kit (Optional) CAUTION Restore power and your light kit is ready for BEFORE STARTING INSTALLATION, DISCO- Disassemble the switch housing cover from the operation. NECT THE POWER BY TURNING OFF THE light kit, you can keep the light kit for future CIRCUIT BREAKER OR REMOVING THE FUSE use. -
Page 16: Operating Your Fan
Operating Your Fan WARNING Warm weather - (Counter-Clockwise direction) A downward air flow creates a cooling effect as LOCKING SLOTS OF CEILING CANOPY ARE PROVIDED ONLY AS AN AID TO MOUNTING. shown in Figure 22. This allows you to set your air DO NOT LEAVE FAN ASSEMBLY UNATTENDED conditioner on a higher setting without affecting UNTIL ALL FOUR CANOPY SCREWS ARE... -
Page 17: Care Of Your Fan
Care of Your Fan Troubleshooting Here are some suggestions to help you maintain PROBLEM SOLUTION your fan. Because of the fan's natural movement, some Fan will not start Check main and branch circuit fuses or breakers. connections may become loose. Check the Check line wire connections to the fan and switch wire support connections, brackets, and blade connections in the switch housing. -
Page 18: Specifications
Specifications FAN SIZE SPEED VOLTS AMPS WATTS N.W. G.W. C.M. 0.17 9.90 30.03 6.55 kg 7.38 kg 36” MED. 0.039' 0.27 25.16 53.36 (14.41 lbs.) (16.28 lbs.) HIGH 0.33 39.13 67.15 These are approximate measures. They do not include Amps and Wattage used by the light kit . Importer: SERVICIOS HOME DEPOT, S.